Journal of Failure Analysis and Prevention

, Volume 17, Issue 3, pp 496–504 | Cite as

Transient Thermal Stress Analysis of BOF Hood Failure

Technical Article---Peer-Reviewed
  • 140 Downloads

Abstract

The failure of BOF hood tube is a common industrial problem that has received little attention in literature. The major mode of failure as observed by most of the industries is thermal fatigue failure. Earlier people have studied the thermal stress profile in hood system considering constant water temperature. However, in reality there are fluctuations in water temperature due to cyclic thermal load caused by BOF gas. Present study reveals that the water temperature fluctuation is having significant impact in causing thermal fatigue failure. The change in water velocity and tube thickness has negligible effect in thermal fatigue failure compared to that observed for water temperature fluctuation. However, tube material of construction is also having significant impact on its failure.

Keywords

BOF hood Thermal stress Modeling Yield stress 

References

  1. 1.
    T. Ondrey, Improvements made to USS Edgar Thomson BOF hood system, in AISE Conference on Prolonging BOF Hood Life (Nashville, Tennessee, 1998)Google Scholar
  2. 2.
    M.L. Wei, Survey of BOF hoods in North America. Iron Steel Eng. 75(4), 25–30 (1998)Google Scholar
  3. 3.
    M.L. Wei, International Survey of BOF hoods, in Conference Proceedings of BOF Hoods for the 21st Century (Nashville, Tennessee, 2000)Google Scholar
  4. 4.
    R.E. Hargraave, D.J. Kotwica, Common failure mechanisms in BOF hoods. Iron Steel Eng. 73(11), 22–28 (1996)Google Scholar
  5. 5.
    I.V. Samarasekera, Mathematical modeling of thermal stresses in basic oxygen furnace hood tubes. Met. Trans. B 16(2), 247–261 (1985)CrossRefGoogle Scholar
  6. 6.
    S.K. Saha, D.J. Radakovic, T.A. Walden, Life extension of BOF lower hood at U. S. Steel Canada’s Lake Erie Works via engineering and design changes, in AISTech Proceedings (Pittsburgh, 2013), pp. 929–938Google Scholar
  7. 7.
    J.F. Mcgurn, Composite tubes in black liquor recovery boilers: an update. Pulp Pap. Canada 94, 12 (1993)Google Scholar
  8. 8.
    H.C. Hottel, Radiant Heat Transmission, 3rd edn, Chap. 4, Heat Transmission (McGraw-Hall Book Company, New York, 1964)Google Scholar
  9. 9.
    G.A. Stemetzki, M.M. Kuta, C. Shepard, BOF hood life cycle cost improvement program. Iron Steel Technol. 1(1), 54–67 (2004)Google Scholar
  10. 10.
    L.C. Boyd Jr., V.K. Sikka, Aluminum bronze alloys to improve the system life of basic oxygen and electric arc furnace hoods, roofs and side vents. Final Report, U. S. Department of Energy (DOE) Information Bridge, 2006, p. 22Google Scholar
  11. 11.
    J.T.P. Castro, R.D. Vieira, A.C.N. Vidal, A.C.O. Miranda, J.L.F. Freire, M.A. Meggiolaro, A case study on corrosion-thermal fatigue damage, R. Marquês de S. Vicente, Rio de Janeiro, Brazil, unpublished literature, 2005Google Scholar
  12. 12.
    J.D. Zupanovich, Oxidation and Degradation Products of Common Oxygen Scavengers. Report (Chem Tech Inc., USA, 2002)Google Scholar
  13. 13.
    P.K. Das, A.K. Gupta, N. Nirmalkar, R.P. Chhabra, Effect of confinement on forced convection from a heated sphere in Bingham plastic fluids. Korea Austrailia Rheol. J. 27(2), 75–94 (2015)CrossRefGoogle Scholar

Copyright information

© ASM International 2017

Authors and Affiliations

  1. 1.Research and Development DivisionTata SteelJamshedpurIndia

Personalised recommendations