Skip to main content
SpringerLink
Log in

Low-Pressure Cold Spraying of Copper–Graphite Solid Lubricating Coatings on Aluminum Alloy 7075-T651

  • Peer Reviewed
  • Published:
Journal of Thermal Spray Technology Aims and scope Submit manuscript

Abstract

Although aluminum alloy 7075-T651 is widely used in the automobile and aircraft manufacturing industries, its durability must often be increased by improving the surface properties of components to better resist wear and oxidation. We propose herein the deposition of copper–graphite solid lubricating coating on aluminum alloy 7075-T651 by using the low-pressure cold-spraying technique. The microstructure, deposition efficiency, mechanical properties, and dry sliding wear behavior of the copper–graphite coatings were investigated. The results showed that addition of Cu-coated graphite particles could decrease the plastic deformation of adjacent copper particles in the coatings. The deposition efficiency, hardness, and bonding strength of the copper–graphite coatings decreased (by 49%, 21%, and 70%, respectively) with an increase in the Cu-coated graphite content in the feedstock from 0 to 20 wt.%. The copper–graphite coating with Cu-coated graphite content of 20 wt.% showed the lowest friction coefficient (about 0.15) and wear rate (6.00 × 10−5 mm3/N m). Compared with aluminum alloy 7075-T651, the friction coefficient and wear rate were decreased by 57% and 78%, respectively, which can mainly be ascribed to the formation of a low-shear-strength graphite-rich solid lubricating film on the worn surface. When the Cu-coated graphite content exceeded 10 wt.%, the dominant wear mechanism changed to mild abrasive wear, in contrast to the oxidative wear of the pure copper coating.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. T. Dursun and C. Soutis, Recent Developments in Advanced Aircraft Aluminium Alloys, Mater. Des., 2014, 56, p 862-871

    Article  CAS  Google Scholar 

  2. J.C. Williams and E.A. Starke, Progress in Structural Materials for Aerospace Systems, Acta Mater., 2003, 51(19), p 5775-5799

    Article  CAS  Google Scholar 

  3. J. Peng, X. Jin, Z. Xu, J. Zhang, Z. Cai, Z. Luo, and M. Zhu, Study on the Damage Evolution of Torsional Fretting Fatigue in 7075 Aluminum Alloy, Wear, 2018, 402-403, p 160-168

    Article  CAS  Google Scholar 

  4. J. Sudagar, K. Venkateswarlu, and J. Lian, Dry Sliding Wear Properties of 7075-T6 Aluminum Alloy Coated with Ni-P(h) in Different Pretreatment Conditions, J. Mater. Eng. Perform., 2009, 19(6), p 810-818

    Article  CAS  Google Scholar 

  5. E. Zalnezhad, A.A.D. Sarhan, and M. Hamdi, Optimizing the PVD TiN Thin Film Coating’s Parameters on Aerospace Al7075-T6 Alloy for Higher Coating Hardness and Adhesion with Better Tribological Properties of the Coating Surface, Int. J. Adv. Manuf. Technol., 2012, 64(1-4), p 281-290

    Article  Google Scholar 

  6. M.A. Ezazi, M.M. Quazi, E. Zalnezhad, and A.A.D. Sarhan, Enhancing the Tribo-mechanical Properties of Aerospace Al7075-T6 by Magnetron Sputtered Ti/TiN, Cr/CrN & TiCr/TiCrN Thin Film Ceramic Coatings, Ceram. Int., 2014, 40(10), p 15603-15615

    Article  CAS  Google Scholar 

  7. M. Couto, S. Dosta, M. Torrell, J. Fernández, and J.M. Guilemany, Cold Spray Deposition of WC-17 and 12Co Cermets on to Aluminum, Surf. Coat. Technol., 2013, 235, p 54-61

    Article  CAS  Google Scholar 

  8. A. Lekatou, D. Sioulas, A.E. Karantzalis, and D. Grimanelis, A Comparative Study on the Microstructure and Surface Property Evaluation of Coatings Produced from Nanostructured and Conventional WC-Co Powders HVOF Sprayed on Al7075, Surf. Coat. Technol., 2015, 276, p 539-556

    Article  CAS  Google Scholar 

  9. Ł. Kaczmarek, B. Adamczyk-Cieślak, J. Mizera, M. Stegliński, K. Kyzioł, D. Miedzińska, Ł. Kołodziejczyk, W. Szymański, and M. Kozanecki, Influence of Chemical Composition of Ti/TiC/a-C: H Coatings Deposited on 7075 Aluminum Alloy on Their Selected Mechanical Properties, Surf. Coat. Technol., 2015, 261, p 304-310

    Article  CAS  Google Scholar 

  10. I. Sudhakar, V. Madhu, G. Madhusudhan Reddy, K. Srinivasa Rao, Enhancement of Wear and Ballistic Resistance of Armour Grade AA7075 Aluminium Alloy Using Friction Stir Processing, Defence Technology, 2015, 11(1), p 10-17

    Article  Google Scholar 

  11. A. Baradeswaran, A. Elaya Perumal, Effect of Graphite on Tribological and Mechanical Properties of AA7075 Composites, Tribol. Trans., 2014, 58(1), p 1-6

    Article  CAS  Google Scholar 

  12. H. Assadi, H. Kreye, F. Gärtner, and T. Klassen, Cold Spraying—A Materials Perspective, Acta Mater., 2016, 116, p 382-407

    Article  CAS  Google Scholar 

  13. V. Champagne and D. Helfritch, The Unique Abilities of Cold Spray Deposition, Int. Mater. Rev., 2016, 61(7), p 437-455

    Article  CAS  Google Scholar 

  14. N. Ata, N. Ohtake, and H. Akasaka, Polyethylene-Carbon Nanotube Composite Film Deposited by Cold Spray Technique, J. Therm. Spray Technol., 2017, 26(7), p 1541-1547

    Article  CAS  Google Scholar 

  15. S.L. Fu, C.X. Li, Y.K. Wei, X.T. Luo, G.J. Yang, C.J. Li, and J.L. Li, Novel Method of Aluminum to Copper Bonding by Cold Spray, J. Therm. Spray Technol., 2018, 27(4), p 624-640

    Article  CAS  Google Scholar 

  16. H. Koivuluoto, A. Coleman, K. Murray, M. Kearns, and P. Vuoristo, High Pressure Cold Sprayed (HPCS) and Low Pressure Cold Sprayed (LPCS) Coatings Prepared from OFHC Cu Feedstock: Overview from Powder Characteristics to Coating Properties, J. Therm. Spray Technol., 2012, 21(5), p 1065-1075

    Article  CAS  Google Scholar 

  17. A. Moridi, S.M. Hassani-Gangaraj, M. Guagliano, and M. Dao, Cold Spray Coating: Review of Material Systems and Future Perspectives, Surf. Eng., 2014, 30(6), p 369-395

    Article  CAS  Google Scholar 

  18. S. Grigoriev, A. Okunkova, A. Sova, P. Bertrand, and I. Smurov, Cold Spraying: from Process Fundamentals towards Advanced Applications, Surf. Coat. Technol., 2015, 268, p 77-84

    Article  CAS  Google Scholar 

  19. H. Assadi, F. Gärtner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379-4394

    Article  CAS  Google Scholar 

  20. H. Koivuluoto, J. Lagerbom, M. Kylmälahti, and P. Vuoristo, Microstructure and Mechanical Properties of Low-Pressure Cold-Sprayed (LPCS) Coatings, J. Therm. Spray Technol., 2008, 17(5-6), p 721-727

    Article  CAS  Google Scholar 

  21. H. Koivuluoto and P. Vuoristo, Effect of Powder Type and Composition on Structure and Mechanical Properties of Cu+Al2O3 Coatings Prepared by Using Low-Pressure Cold Spray Process, J. Therm. Spray Technol., 2010, 19(5), p 1081-1092

    Article  CAS  Google Scholar 

  22. K. Ogawa, K. Ito, K. Ichimura, Y. Ichikawa, S. Ohno, and N. Onda, Characterization of Low-Pressure Cold-Sprayed Aluminum Coatings, J. Therm. Spray Technol., 2008, 17(5-6), p 728-735

    Article  CAS  Google Scholar 

  23. A. Astarita, M. Durante, A. Langella, M. Montuori, and A. Squillace, Mechanical Characterization of Low-Pressure Cold-Sprayed Metal Coatings on Aluminium, Surf. Interface Anal., 2013, 45(10), p 1530-1535

    Article  CAS  Google Scholar 

  24. Y. Zhang, J. Michael Shockley, P. Vo, and R.R. Chromik, Tribological Behavior of a Cold-Sprayed Cu-MoS2 Composite Coating during Dry Sliding Wear, Tribol. Lett., 2016, 62(1), p 1-12

    Article  CAS  Google Scholar 

  25. Y. Zhang, S. Descartes, P. Vo, and R.R. Chromik, Cold-Sprayed Cu-MoS2 and Its Fretting Wear Behavior, J. Therm. Spray Technol., 2015, 25(3), p 473-482

    Article  CAS  Google Scholar 

  26. A. Loganathan, S. Rengifo, A.F. Hernandez, Y. Emirov, C. Zhang, B. Boesl, J. Karthikeyan, and A. Agarwal, Effect of 2D WS2 Addition on Cold-Sprayed Aluminum Coating, J. Therm. Spray Technol., 2017, 26(7), p 1585-1597

    Article  CAS  Google Scholar 

  27. L.M. Stark, I. Smid, A.E. Segall, T.J. Eden, and J. Potter, Self-Lubricating Cold-Sprayed Coatings Utilizing Microscale Nickel-Encapsulated Hexagonal Boron Nitride, Tribol. Trans., 2012, 55(5), p 624-630

    Article  CAS  Google Scholar 

  28. W. Chen, Y. Yu, J. Cheng, S. Wang, S. Zhu, W. Liu, and J. Yang, Microstructure, Mechanical Properties and Dry Sliding Wear Behavior of Cu-Al2O3-Graphite Solid-Lubricating Coatings Deposited by Low-Pressure Cold Spraying, J. Therm. Spray Technol., 2018, 27(8), p 1652-1663

    Article  CAS  Google Scholar 

  29. K.I. Triantou, D.I. Pantelis, V. Guipont, and M. Jeandin, Microstructure and Tribological Behavior of Copper and Composite Copper+Alumina Cold Sprayed Coatings for Various Alumina Contents, Wear, 2015, 336-337, p 96-107

    Article  CAS  Google Scholar 

  30. X.-J. Ning, J.-H. Jang, and H.-J. Kim, The Effects of Powder Properties on In-flight Particle Velocity and Deposition Process during Low Pressure Cold Spray Process, Appl. Surf. Sci., 2007, 253(18), p 7449-7455

    Article  CAS  Google Scholar 

  31. P. Sudharshan Phani, D. Srinivasa Rao, S.V. Joshi, and G. Sundararajan, Effect of Process Parameters and Heat Treatments on Properties of Cold Sprayed Copper Coatings, J. Therm. Spray Technol., 2007, 16(3), p 425-434

    Article  CAS  Google Scholar 

  32. J. Kováčik, Š. Emmer, J. Bielek, and L.U. Keleši, Effect of Composition on Friction Coefficient of Cu-Graphite Composites, Wear, 2008, 265(3-4), p 417-421

    Article  CAS  Google Scholar 

  33. S.A. El-Badry, S.F. Moustafa, A.M. Sanad, and B. Kieback, Friction and Wear of Copper-Graphite Composites Made with Cu-coated and Uncoated Graphite Powders, Wear, 2002, 253, p 699-710

    Article  Google Scholar 

  34. E. Avcu, The Influences of ECAP on the Dry Sliding Wear Behaviour of AA7075 Aluminium Alloy, Tribol. Int., 2017, 110, p 173-184

    Article  CAS  Google Scholar 

  35. E.P. Georgioua, S. Achantab, S. Dostac, J. Fernándezc, P. Matteazzid, J. Kusinskie, and J.-P.C.R.R. Piticescuf, Structural and Tribological Properties of Supersonic Sprayed Fe-Cu-Al-Al2O3 Nanostructured Cermets, Appl. Surf. Sci., 2013, 245, p 142-147

    Article  CAS  Google Scholar 

  36. P. Cavaliere and A. Silvello, Fatigue Behaviour of Cold Sprayed Metals and Alloys: Critical Review, Surf. Eng., 2016, 32(9), p 631-640

    Article  CAS  Google Scholar 

  37. L. Su, F. Gao, X. Han, R. Fu, and E. Zhang, Tribological Behavior of Copper-Graphite Powder Third Body on Copper-Based Friction Materials, Tribol. Lett., 2015, 60(2), p 1-12

    Article  CAS  Google Scholar 

Download references

Acknowledgments

This work was supported by the National Natural Science Foundation of China (51675511 and 51675510).

Author information

Authors and Affiliations

  1. State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou, 730000, China

    Wenyuan Chen, Yuan Yu, Shengyu Zhu, Weimin Liu & Jun Yang

  2. Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing, 100049, China

    Wenyuan Chen, Shengyu Zhu, Weimin Liu & Jun Yang

  3. State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou University of Technology, Lanzhou, 730050, China

    Jiqiang Ma

Authors
  1. Wenyuan Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Yuan Yu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jiqiang Ma
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Shengyu Zhu
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Weimin Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Jun Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to Shengyu Zhu or Jun Yang.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Chen, W., Yu, Y., Ma, J. et al. Low-Pressure Cold Spraying of Copper–Graphite Solid Lubricating Coatings on Aluminum Alloy 7075-T651. J Therm Spray Tech 28, 1688–1698 (2019). https://doi.org/10.1007/s11666-019-00905-w

Download citation

  • Received:

  • Revised:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11666-019-00905-w

Keywords

Search

Navigation