Abstract
For the dissimilar laminated metal composite sheets (LMCS) fabricated by roll bonding technology, the great differences of mechanical properties between the constituent metals lead to the non-uniform deformation and individual layer necking. The individual layer shape affects the mechanical properties and microstructure of dissimilar LMCS. The Al/Al alloy (1100/7075) LMCS with the same thickness and ratio of dissimilar metals, but different individual layer shapes, have been successfully fabricated by hot accumulative roll bonding in conjunction with cold rolling technology. Some effective methods (such as sheet crown, warp degree, and slant angle) were presented to quantitatively evaluate the individual layer shape and necking of constituent metals. The microstructure and mechanical properties of 1100/7075 LMCS with different individual layer shapes were investigated. The effects of bonding interface on the mechanical properties were obtained based on the assessment of individual layer shapes and necking. The strength and elongation of LMCS decrease with the increase of variation of individual layer shapes and necking when the number of layers keeps constant. The research results offer some theoretical guides and references for adjusting the control measures of compatibility deformation, optimizing the hot roll bonding technologies, and designing the novel high-performance dissimilar LMCS.
Similar content being viewed by others
References
D.R. Lesuer, C.K. Syn, and O.D. Sherby, Mechanical Behaviour of Laminated Metal Composites, Int. Mater. Rev., 1996, 41(5), p 169–197
J. An, Y.B. Liu, and D.R. Sun, Mechanism of Bonding of Al-Pb Alloy Strip and Hot Dip Aluminised Steel Sheet by Hot Rolling, Mater. Sci. Technol., 2001, 17(4), p 451–454
J. Oh, W.C. Lee, and S.G. Pyo, Microstructural Analysis of Multilayered Titanium Aluminide Sheets Fabricated by Hot Rolling and Heat Treatment, Metall. Mater. Trans. A, 2002, 33(12), p 3649–3659
F.X. Yin, L. Li, and Y. Tanaka, Hot Rolling Bonded Multilayered Composite Steels and Varied Tensile Deformation Behaviour, Mater. Sci. Technol., 2012, 28(7), p 783–787
J.T. Liu, M. Li, S. Sheu, and M.E. Karabin, Macro- and Micro-Surface Engineering to Improve Hot Roll Bonding of Aluminum Plate and Sheet, Mater. Sci. Eng. A, 2008, 479(1-2), p 45–57
H. Sheikh and E. Paimozd, Effect of Hot Accumulative Roll Bonding Process on the Mechanical Properties of AA5083, Open J. Met., 2011, 1(1), p 12–15
D. Pan, K. Gao, and J. Yu, Cold Roll Bonding of Bimetallic Sheet and Strips, Mater. Sci. Technol., 1989, 5, p 934–939
L. Li, K. Nagai, and F. Yin, Progress in Cold Roll Bonding of Metals, Sci. Technol. Adv. Mater., 2008, 9, p 023001–023011
R. Jamaati and M.R. Toroghinejad, Cold Roll Bonding Bond Strengths: Review, Mater. Sci. Technol., 2011, 27(7), p 1101–1108
R. Jamaati and M.R. Toroghinejad, Effect of Friction, Annealing Conditions and Hardness on the Bond Strength of Al/Al Strips Produced by Cold Roll Bonding Process, Mater. Des., 2010, 31(9), p 4508–4513
H.S. Liu, B. Zhang, and G.P. Zhang, Enhanced Plasticity of Cu-Based Laminated Composites Produced by Cold Roll-Bonding, Mater. Sci. Forum, 2011, 667-669, p 1015–1020
L.Y. Sheng, F. Yang, T.F. Xi, C. Lai, and H.Q. Ye, Influence of Heat Treatment on Interface of Cu/Al Bimetal Composite Fabricated by Cold Rolling, Compos. B Eng., 2011, 42(6), p 1468–1473
H.Z. Yan and J.G. Lenard, A Study of Warm and Cold Roll-Bonding of an Aluminium Alloy, Mater. Sci. Eng. A, 2004, 385(1-2), p 419–428
M. Eizadjou, H.D. Manesh, and K. Janghorban, Mechanism of Warm and Cold Roll Bonding of Aluminum Alloy Strips, Mater. Des., 2009, 30(10), p 4156–4161
C.Y. Liu, Q. Wang, and Y.Z. Jia, Microstructures and Mechanical Properties of Mg/Mg and Mg/Al/Mg Laminated Composites Prepared Via Warm Roll Bonding, Mater. Sci. Eng. A, 2012, 556, p 1–8
S.H. Kim, H.W. Kim, and Kwangjun. Euh, Effect of Wire Brushing on Warm Roll Bonding of 6XXX/5XXX/6XXX Aluminum Alloy Clad Sheets, Mater. Des., 2012, 35, p 290–295
G. Heness, R. Wuhrer, and W.Y. Yeung, Interfacial Strength Development of Roll-Bonded Aluminium/Copper Metal Laminates, Mater. Sci. Eng. A, 2008, 483-484, p 740–742
J. Wang, R.G. Hoagland, and X.Y. Liu, The Influence of Interface Shear Strength on the Glide Dislocation-Interface Interactions, Acta Mater., 2011, 59(8), p 3164–3173
C.M. Cepeda-Jimenez, M. Pozuelo, and J.M. Garcia-Infanta, Influence of the Alumina Thickness at the Interfaces on the Fracture Mechanisms of Aluminium Multilayer Composites, Mater. Sci. Eng. A, 2008, 496(1-2), p 133–142
I.-K. Kim and S.I. Hong, Effect of Heat Treatment on the Bending Behavior of Tri-layered Cu/Al/Cu Composite Plates, Mater. Des., 2013, 47, p 590–598
Z. Chen, and K. Nyirenda, The Effect of Heat Treatment Technology on Mechanical Properties of Al/Al Alloys Multilayer Sheet Fabricated by Hot Roll Bonding, ICAA13: 13th International Conference on Aluminum Alloys, H. Weiland, A.D. Rollett, W.A. Cassada, Eds, June 3-7th, 2012, (Pennsylvania, US). The Minerals, Metals, & Materials Society, John Wiley & Sons, 2012, p 1705–1711
M.R. Toroghinejad, F. Ashrafizadeh, R. Jamaati, Majid. Hoseini, and Jerzy.A. Szpunar, Textural Evolution of Nanostructured AA5083 Produced by ARB, Mater. Sci. Eng. A, 2012, 556, p 351–357
M. Tayyebi and B. Eghbali, Study on the Microstructure and Mechanical Properties of Multilayer Cu/Ni Composite Processed by Accumulative Roll Bonding, Mater. Sci. Eng. A, 2013, 559, p 759–764
M.R. Toroghinejad, R. Jamaati, and M. Hoseini, Texture Evolution of Nanostructured Aluminum/Copper Composite Produced by the Accumulative Roll Bonding and Folding Process, Metall. Mater. Trans. A, 2013, 44(3), p 1587–1598
Y.Z. Tian and Z.F. Zhang, Stability of Interfaces in a Multilayered Ag-Cu Composite During Cold Rolling, Scr. Mater., 2013, 68(7), p 542–545
I. Topic, H.W. Höppel, and M. Göken, Influence of Rolling Direction on Strength and Ductility of Aluminium and Aluminium Alloys Produced by Accumulative Roll Bonding, J. Mater. Sci., 2008, 43(23-24), p 7320–7325
A. Azushima, R. Kopp, and A. Korhonen, Severe Plastic Deformation (SPD) Processes for Metals, CIRP Annu. Manuf. Technnol., 2008, 57(2), p 716–735
Y. Saito, N. Tsuji, and H. Utsunomiya, Ultra-fine Grained Bulk Aluminum Produced by Accumulative Roll-Bonding (ARB) Process, Scr. Mater., 1998, 39(9), p 1221–1227
N. Kamikawa, X. Huang, N. Tsuji, and N. Hansen, Strengthening Mechanisms in Nanostructured High-Purity Aluminium Deformed to High Strain and Annealed, Acta Mater., 2009, 57(14), p 4198–4208
D. Terada, S. Inoue, and N. Tsuji, Microstructure and Mechanical Properties of Commercial Purity Titanium Severely Deformed by ARB Process, J. Mater. Sci., 2007, 42(5), p 1673–1681
M. Eizadjou, A.K. Talachi, and H.D. Manesh, Investigation of Structure and Mechanical Properties of Multi-Layered Al/Cu Composite Produced by Accumulative Roll Bonding (ARB) Process, Compos. Sci. Technol., 2008, 68(9), p 2003–2009
K. Wu, H. Chang, E. Maawad, W.M. Gan, H.G. Brokmeier, and M.Y. Zheng, Microstructure and Mechanical Properties of the Mg/Al Laminated Composite Fabricated by Accumulative Roll Bonding (ARB), Mater. Sci. Eng. A, 2010, 527(13-14), p 3073–3078
S. Roy, B.R. Nataraj, S. Suwas, S. Kumar, and K. Chattopadhyay, Accumulative Roll Bonding of Aluminum Alloys 2219/5086 Laminates: Microstructural Evolution and Tensile Properties, Mater. Des., 2012, 36, p 529–539
K. Nyirenda, and Z. Chen, Mechanical Properties of Multilayer 1100/7075 Aluminum Sheet Produced by Hot ARB, ICAA13: 13th International Conference on Aluminum Alloys, H. Weiland, A.D. Rollett, W.A. Cassada, Eds, June 3-7th, 2012, (Pennsylvania, US). The Minerals, Metals, & Materials Society, John Wiley & Sons, 2012, p 1753–1760
T. Hausöl, H.W. Höppel, and M. Göken, Tailoring Materials Properties of UFG Aluminium Alloys by Accumulative Roll Bonded Sandwich-Like Sheets, J. Mater. Sci., 2010, 45(17), p 4733–4738
T. Hausöl, H.W. Höppel, and M. Göken, Ultrafine-Grained AA6014/AA5754 Laminates Produced by Accumulative Roll Bonding (ARB), Mater. Werkstofftech., 2012, 43(4), p 334–339
L. Su, C. Lu, A. Kiet Tieu, G. Deng, and X. Sun, Ultrafine Grained AA1050/AA6061 Composite Produced by Accumulative Roll Bonding, Mater. Sci. Eng. A, 2013, 559, p 345–351
A. Mozaffari, H.D. Manesh, and K. Janghorban, Evaluation of Mechanical Properties and Structure of Multilayered Al/Ni Composites Produced by Accumulative Roll Bonding (ARB) Process, J. Alloys Compd., 2010, 489(1), p 103–109
R.N. Dehsorkhi, F. Qods, and M. Tajally, Investigation on Microstructure and Mechanical Properties of Al-Zn Composite During Accumulative Roll Bonding (ARB) Process, Mater. Sci. Eng. A, 2011, 530, p 63–72
A. Shabani, M.R. Toroghinejad, and A. Shafyei, Fabrication of Al/Ni/Cu Composite by Accumulative Roll Bonding and Electroplating Processes and Investigation of its Microstructure and Mechanical Properties, Mater. Sci. Eng. A, 2012, 558, p 386–393
M.R. Toroghinejad, F. Ashrafizadeh, and R. Jamaati, On the Use of Accumulative Roll Bonding Process to Develop Nanostructured Aluminum Alloy 5083, Mater. Sci. Eng. A, 2013, 561, p 145–151
N.V. Govindaraj, J.G. Frydendahl, and B. Holmedal, Layer Continuity in Accumulative Roll Bonding of Dissimilar Material Combinations, Mater. Des., 2013, 52, p 905–915
Acknowledgments
This research project is supported by the National High Technology Research and Development Program of China (863 Program, No. 2013AA031304), the National Natural Science Foundation of China (No. 50890172), and the Danish-Chinese Center for Nanometals.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Chen, Z., Wu, X., Hu, H. et al. Effect of Individual Layer Shape on the Mechanical Properties of Dissimilar Al Alloys Laminated Metal Composite Sheets. J. of Materi Eng and Perform 23, 990–1001 (2014). https://doi.org/10.1007/s11665-013-0804-8
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-013-0804-8