Abstract
Al 1050/Al 5083 multilayer laminate composites were produced by accumulative roll bonding (ARB) process up to three cycles at room temperature. Tensile strength along rolling direction and hardness was evaluated for base alloys and laminate composites. As compared to the base alloys, tensile strength and hardness of Al laminate composites increase significantly after every ARB cycle. The third cycle ARBed sample exhibited the tensile strength of 202 MPa, which is 29% more than the first cycle ARBed sample. Similarly, the BHN (Brinell hardness number) of the third cycle ARBed sample is 73, which is 46% more than the first cycle ARBed sample. ARBed samples show very limited elongation. Microstructural evolutions of ARBed sheets were analyzed by scanning electron microscopy (SEM). Analysis revealed that grains of Al were refined significantly after every ARB cycle.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
An J, Lu Y, Xu DW, Liu YB, Sun DR, Yang B (2001) Hot-roll bonding of Al-Pb bearing alloy strips and hot dip aluminized steel sheets. J Mater Eng Perform 10(2):131
Verlinden B (2002/2004) Severe plastic deformation of metals. In: Zhu YT et al (eds) The second and third international conference on ultrafine grained materials, TMS
Azushima A, Kopp R, Korhonen A, Yang DY, Micari F, Lahoti GD, Groche P, Yanagimoto J, Tsuji N, Rosochowski A, Yanagida A (2008) Severe plastic deformation (SPD) processes for metals. CIRP Ann Manuf Technol 57:716–735
Tsuji N, Saito Y, Lee SH, Minamino Y (2003) ARB and other new techniques to produce bulk ultrafine grained materials. Adv Eng Mater 5(5):338–344
Eizadjou M, Talachi AK, Manesh HD, Shahabi HS, Janghorban K (2008) Investigation of structure and mechanical properties of multi-layered Al/Cu composite produced by accumulative roll bonding (ARB) process. Compos Sci Technol 68(2008):2003–2009
Toroghinejad MR, Jamaati R, Dutkiewicz J, Szpunar JA (2013) Investigation of nanostructured aluminum/copper composite produced, by accumulative roll bonding and folding process. Mater Des 51(2013):274–279
Hsieh C-C, Chen M-C, Wu W (2013) Mechanical property and fracture behavior of Al/Mg composite produced by accumulative roll bonding technique. J Compos 2013(748273):8 pages
Salimi S, Izadi H, Gerlich AP (2011) Fabrication of an aluminum–carbon nanotube metalmatrix composite by accumulative roll-bonding. J Mater Sci 46:409–415
Yu HL, Lu C, Tieu AK, Kong C (2014) Fabrication of nanostructured aluminum sheets using four-layer accumulative roll bonding. Mater Manuf Process 29(4)
Jamaati R, Toroghinejad MR, Amirkhanlou S, Edris H (2015) On the achievement of nanostructured interstitial free steel by four-layer accumulative roll bonding process at room temperature. Metall Mater Transactions A 46A:4013–4019
Lahiri D, Bakshi SR, Keshri AK, Liu Y, Agarwal A (2009) Dual strengthening mechanisms induced by carbon nanotubes in roll bonded aluminum composites. Mater Sci Eng A 523:263–270
Bachmaier A, Pippan R (2013) Generation of metallic nanocomposites by severe plastic deformation. Int Mater Rev 58(1):41–62
Amirkhanlou S, Ketabchi M, Parvin N, Khorsand S, Bahram R (2013) Accumulative press bonding; a novel manufacturing process of nanostructured metal matrix composites. Mater Des 51:367–374
Kim HS, Estrin Y Bush MB (2000) Plastic deformation behaviour of fine-grained materials. Acta Mater 48(2000):493–504
Nieh TG, Wadsworth J (1991) Hall-petch relation in nanocrystalline solids. Scr Metall Mater 25(4):955–958
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Poovazhagan, L., Ruthran, P., Sreyas, S., Thamizharasan, A., Thejas, S. (2019). Microstructure Evolution and Mechanical Properties of Al 1050/Al 5083 Laminate Composites Produced by Accumulative Roll Bonding Process. In: Lakshminarayanan, A., Idapalapati, S., Vasudevan, M. (eds) Advances in Materials and Metallurgy. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-13-1780-4_4
Download citation
DOI: https://doi.org/10.1007/978-981-13-1780-4_4
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-1779-8
Online ISBN: 978-981-13-1780-4
eBook Packages: EngineeringEngineering (R0)