Abstract
Olive oil extraction has recently experienced a continuous increase due to its related beneficial properties. Consequently, large amounts of olive mill wastes (OMWs) derived from the trituration process are annually produced, causing serious environmental problems. The limited financial capabilities of olive mills make them usually unable to bear the high costs required for the disposal of their wastes. Alternatively, the valorization of OMWs within the framework of the so-called waste-to-resource concept and their recycling can represent a successful strategy for the implementation of circular economy model in the olive industry, which could have significant socioeconomic impacts on low-income Mediterranean countries. There is, however, no unique solution for OMWs valorization, due to the wide variety of the wastes’ composition and their seasonal production. In this review, the potential of OMWs for being reused and the recent technological advances in the field of OMWs valorization are assessed. Special focus is given to the analysis of the advantages and limitations of each technology and to reporting the most significant issues that still limiting its industrial scale-up. The information collected in this review shows that OMW could be effectively exploited in several sectors, including energy production and agriculture. OMWs potential seems, however, undervalued, and the implementation of sustainable valorization strategies in large-scale remains challenging. More efforts and policy actions, through collective actions, encouraging subsidies, and establishing public–private collaborations, are still needed to reconcile research progress with industrial practices and encourage the large-scale implementation of the waste-to-resource concept in the olive sector.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
With more than 3 million tons of olive oil produced annually, the olive oil extraction industry is considered as one of the most important agro-industrial sectors in the Mediterranean countries, contributing significantly to their economic and social development. Thanks to its nutritional value and content of bioactive compounds, olive oil is one of the most important food trends in the world and its demand is constantly increasing (Donner and Radic 2021). Olive oil is extracted either by traditional pressing or by three-phase centrifugal or two-phase centrifugal extraction processes. Although these processes may differ in the technology used and the quality of the extracted olive oil, they are similar in producing large amounts of wastes and by-products. It is assumed that the extraction of one metric ton of olive oil using three-phase systems produces in average 0.6 ton of olive mill solid waste (OMSW) and around 1.5 m3 of olive mill wastewater (OMWW). The use of the two-phase process, which is introduced as more ecofriendly extraction process, can reduce the amount of OMWW by 75%, but produces a semi-solid waste with higher moisture content (Markou and Georgakakis 2010). In overall, the total production of waste biomass generated from the extraction of olive oil is estimated to be at least 40 Mt/year, in which more than 20 Mt/year is corresponding to dry biomass (Di Giacomo and Romano 2022), while only OMWW annual production is estimated between 10 and 30 million m3/year (Annab et al. 2019).
Olive mill wastes (OMWs) produced by the different olive oil extraction processes are characterized by undesirable color and odor, high acidity, high salt content, low alkalinity, and a very high organic load (Enaime et al. 2020a). OMWs are also characterized by a high content in phenolic compounds, which makes them phytotoxic and non-biodegradable (El-Abbassi et al. 2017). Until recently, these residues were considered undesirable due to their negative impact on the environment and the high costs required for their management and disposal. The management of OMWs is also challenging due to their seasonal production and the territorial dispersion of olive mills (Ntougias et al. 2013). The most common strategies adopted by olive oil producers are storage in open ponds or direct discharge into river streams for OMWW and use as fuel in co-incinerators for energy production for OMSW. Although these practices are relatively less expensive, they are however not considered as eco-friendly as they cause supplementary environmental issues such as soil and aquatic systems contamination, bad odors, high proliferation of insects and harmful methane emissions (Markou and Georgakakis 2010). Growing global awareness of the environmental challenges facing the world has increased the pressure to find sustainable alternatives to these traditional practices. The fact that OMWs are rich in organics and bioactive compounds, research is recently more oriented toward their valorization instead of their treatment using destructive methods, particularly with the promotion of the new approach of circular economy. OMWs are then no longer considered as a problem to be eliminated, but as a potential to be exploited (Fig. 1).
There is no exclusive solution for the valorization of OMWs. The choice of the appropriate recovery method depends on the properties of the waste, the local conditions, and the specific needs of olive oil producers. OMWs could be used in beneficial ways for bioenergy and biodiesel production in low-income countries, which will help reducing their need for foreign energy sources. These residues could also be used in many other applications, from the production of adsorbent materials for wastewater treatment to the extraction of valued antioxidants and the production of biofertilizer and soil amendments (Messineo et al. 2020; Uddin et al. 2021). OMWs can also be reused as growth medium for algae (Hodaifa et al. 2013b), as additive incorporated into construction materials (Hytiris et al. 2004), and to produce biopolymeric substance (Ntaikou et al. 2009). Despite the promising results obtained regarding the valorization of OMWs and their conversion into valuable resources, the large-scale application of the suggested methods is still limited for many technical and economic considerations. This contribution summarizes the key research investigations reporting on the valorization of OWMs and their use as resources instead of their treatment as wastes. Specific questions were as follows: What are the drivers and characteristics of the potential implementation of the new concept of wastes to resources in olive sector? What is the current knowledge related to this issue? What are the main limitations hindering the large adoption of this promising strategy and what are the future prospects?
Olive mill wastes utilization techniques
Considering the big challenges facing today’s world, including high population increase, environmental pollution, and resources scarcity, new alternatives in the waste management sector that fit into the new concept of circular economy have recently being promoted. The circular economy, as previously defined, is an alternative business model which, unlike the linear model, consists of an intentionally regenerative industrial system, based on reusing materials that have reached their end of life and thereby increasing their value while reducing waste to a minimum (Murray et al. 2015). The large amount of OMWs generated annually has typically no industrial application and therefore constitutes a real challenge for olive mills. These wastes fall into the category of highly polluting and phytotoxic wastes and are therefore only considered from a treatment point of view. Pushed institutionally by the strength regulations and socially by the increased ecological awareness, olive oil producing industries are forced to start thinking about defining new directives for a transition towards circular economy models for a better management of their wastes. Within this concept, OMWs are considered as raw materials that could be directly used or converted into valuable products, allowing potential additional incomes for olive mill operators and making olive oil value chain more sustainable and environmentally friendly. In recent years, many efforts have been made to develop ways to effectively take advantage of these residues and recover their energy potential. Table 1 and the following sections will report the most important forms of recovery reported in the literature.
OMWs as source of energy
Thermochemical methods
The use of thermochemical methods for energy utilization is mainly suitable for OMSW characterized by their lower water content, as compared to OMWW, and their considerable amount of energy (LHV = 15.58–19.81 MJ/kg), two important factors for considering a potential thermochemical utilization plant (Fokaides and Polycarpou 2013). OMSW has been directly used to produce heat and power through direct combustion. For instance, olive stones have been largely used as a substitute for fossil fuels in domestic boilers, in industrial plants or even in public heating systems (Pattara et al. 2010; López et al. 2010). Veraa et al. (2013) reported that a small-scale plant based on a downdraft gasifier fed with OMWs; small branches and leaves as well as crushed pits and a gas engine connected to the grid were able to provide 70 kWelectric and 110 kWthermal as sanitary hot water needed in the olive oil extraction process with a biomass consumption of 105 kg/h. OMSW could be either combusted alone or in combination with other fuels having similar densities and energy contents such as coal (Niaounakis and Halvadakis 2006). Armesto et al. (2003) used effectively a bubbling fluidized bed in a pilot plant for the co-combustion of OMSW and two different coals, namely lignite and anthracite for energy generation purposes. The effectiveness of the co-combustion of various mixtures of olive cake with lignite coal was also confirmed by Atimtay and Topal (2004) using a circulating fluidized bed.
The direct application of OMSW for energy generation could be however associated to some limitations, mainly related to their moisture content (especially for two-phase olive mill waste; TPOMW), which increases packaging, storage and transportation costs and decreases the efficiency of the combustion process, while promoting a high CO emission (Enaime et al. 2022). The increase in CO emission is also observed due to the high content of OMSW in volatile matter. Topal et al. (2003) compared the combustion efficiency of olive cake and lignite coal treated separately and their co-combustion in a circulating fluidized bed. The results showed that CO and CH4 emissions are more important for olive cake than those for lignite coal due to its higher volatile matter content. Some operational problems like agglomeration, fouling, and corrosion could also occur as a result of the presence of impurities in OMSW, particularly alkali metals such as potassium and sodium (Enaime et al. 2022). To overcome these issues and effectively use OMSW as a biofuel, a processing step to upgrade their fuel properties prior to combustion is then required. Thermal conversion methods, like pyrolysis (Hmid et al. 2014), torrefaction (Benavente and Fullana 2015), gasification (Ducom et al. 2020), and hydrothermal carbonization (HTC) (Enaime et al. 2022), have been suggested to homogenize and convert OMSW into a form similar to coal. The application of these technologies allows a very significant reduction in volume, while effectively increasing the combustion efficiency of the produced carbon material as compared to the original biomass. Depending on the technology used, the distribution and properties of the resulting by-products vary. Choosing one method over another requires an in-depth knowledge of the nature and composition of the substrate and the intended application. For instance, TPOMW with high water content (> 70% water content) could be effectively treated by HTC without the need of energy intensive drying step. Benavente et al. (2017) confirmed that the hydrothermal conversion of TPOMW into hydrochar and its combustion with energy recovery resulted in net environmental savings for all impact categories with the exception of the impacts related to the untreated HTC process water. In another study, Volpe and Fiori (2017) used HTC to convert olive tree trimmings and olive pulp into hydrochar. The solid load proved to be a crucial parameter in determining the energy properties of produced hydrochars. The higher the solid charge, the higher the degree of carbonization, the yield of hydrochars and their energy content. In the same study, authors compared between the fuel properties of olive waste-derived char produced via HTC and low-temperature pyrolysis in a specific set of reaction conditions. Authors showed that HTC can be performed at a temperature 50 °C lower than that used in low-temperature pyrolysis in order to obtain similar biochar thermochemical properties. The fact that HTC is conducted at lower temperatures means that most of the starting mass is conserved, allowing for larger final yields as compared to pyrolysis chars (typically less than 60%) (Naisse et al. 2013). Interestingly, OMWW has also been used by Azzaz and co-authors as a feedstock for biofuel production via HTC (Azzaz et al. 2020). Authors claimed that HTC could be effectively applied to convert OMWW into a carbon-rich material with promising energy contents, up to 35.70 MJ/kg at HTC temperature of 220 °C. Conversely, Poerschmann et al. (2013) concluded that OMWW is not an ideal substrate for HTC treatment based on their low carbohydrates fraction, which allowed for low biochar yield production (30%, w/w). Alternatively, the co-hydrothermal treatment of OMSW and OMWW has been suggested. Volpe et al. (2018) successfully used HTC for the conversion of an olive waste stream mixture (olive pulp, kernels and OMWW) coming from a three phase-continuous process into a pelletized solid biofuel that showed high energy density and mechanical stability. Similarly, Enaime et al. (2022) applied HTC on olive stones previously used for OMWW filtration. The filter bed, exhibiting a moisture content of about 57%, was proved to be a good substrate for the production of solid biofuel (HHV = 31.0 MJ/kg) via HTC.
Biochemical methods
OMWs characterized by their high organic load especially in oil could be converted into various biofuels including methane, ethanol, and hydrogen using different biochemical techniques, such as anaerobic digestion and fermentation.
Methane production
The anaerobic treatment of OMWW for biogas production has been extensively documented in the literature. The produced biogas could be directly used for combined heat and power generation or its transformation into natural gas-quality bio-methane. The high organic load of OMWW and the presence of phenolic compounds seem, however, to affect the growth of many bacteria and to interfere with the activity of methanogenic consortia, thus limiting the effectiveness of any direct application of biological processes. One of the widely applied solutions to reduce the organic load of OMWW is their dilution, although this solution is a high-water consuming method and therefore generates a substantially larger volume of wastewater. Pretreatment with acidic, basic and saline chemicals; advanced chemical oxidation; and aerobic pretreatments are among many other pretreatment methods that have been also applied on OMWW prior to its use for methane production (Gunaya and Karadag 2015). Aerobic pretreatment has been effectively used to selectively attenuate the presence of phenolic compounds in OMWW. González-González and Cuadros (2014) reached a polyphenols removal efficiency of 56% after the first day of aerating OMWW by using indigenous microorganisms and a maximum removal of 90% by day 7. Aerobic pretreatments are, however, leading to a significant decrease in COD concentration, which reduces the potential for CH4 production in addition to the requirement for continuous and long-term aeration, leading to considerable energy consumption (Gunaya and Karadag 2015). A sustainable approach for the pretreatment of OMWW before anaerobic treatment has been investigated by Enaime et al. (2019), which consisted of the filtration of OMWW on olive stones followed by coagulation-flocculation as a second pretreatment step. This combined pretreatment process resulted in a total suspended solid and fatty matter depletion of about 82.5% and 73.8% and a simultaneous depletion of phenolic compounds and COD of about 11.3% and 23.2%, respectively. These results confirm the applicability of such an integrated system to enhance the treatability of OMWW for a further biological post-treatment as reported by Enaime et al. (2019).
OMSW has also been the subject of numerous investigations aiming at studying their anaerobic biodegradability and their biochemical methane potential. Borja et al. (2002) succeeded in operating a laboratory-scale reactor designed in digesting TPOMW under mesophilic conditions. The results showed that the daily production of methane increased linearly with the increase in organic loading rate (OLR). High removal efficiencies of COD and volatile solids (88.4 and 90.9%, respectively) and a maximum CH4 production rate of 2.12 l CH4/L day were achieved at an OLR of 12.02 g COD/L day, whereas the methane production rate decreased slightly when the OLR was increased from 12.02 to 15.03 g COD/L day. A linear increase in the CH4 production rate when the OLR increased from 1.5 to 9.2 g COD/L day with a COD removal efficiency ranging from 97 to 77% was achieved by Rincon et al. (2008) during the anaerobic digestion of TPOMW in a laboratory-scale continuous stirred tank reactor. The increase in the OLR was accompanied by a drastic decrease in the CH4 production rate. Authors noted a failure of the system when the reactor was operating at OLR higher than 9.2 g COD/L day. For both studies, an acclimatation step has been reported crucial to adapt the biomass to the nature of the TPOMW and improve its biodegradability and to enhance the methanization process.
The addition of nitrogen, an essential element for microbial activity, is necessary for the anaerobic treatment of OMWs to compensate for its deficiency. Co-digestion of OMWs with nitrogen-rich substrates, such as animal manures or slurries, municipal organic wastes, and agro-industrial wastes, was largely used to avoid nutrient deficiency and ensure an optimal C/N ratio, generally reported to be 20–30 (Maragkaki et al. 2018; Zheng et al. 2015). In addition to its ability to create an optimal balance among nutrients, trace elements, and pH, the co-digestion of OMWs and other feedstocks could be considered as an attractive management method as it offers the possibility of simultaneously processing two or several feedstocks in one reactor. In addition, it allows the dilution of toxic compounds and inhibitors present in OMWs, hence improving the stability of the process and the production of biogas (Mata-Alvarez et al. 2014; Shah et al. 2015). Azbar et al. (2008) reported an enhancement of biogas production by about 90% when OMWW was mixed with laying hen litter, while 22% more was achieved when mixed with cheese whey. Interestingly is the co-digestion of OMWW with OMSW as both streams are a problematic issue for olive mill operators and OMSW is a substrate rich in nitrogen (TKN = 10–20 g N/kg total solid) that could be used to compensate for OMWW lack in alkalinity and ammonium. Boubaker and Ridha (2007) investigated the anaerobic co-digestion of OMWW with OMSW in laboratory-scale using tubular digesters operated at mesophilic temperatures and fed semi-continuously at OLRs varying from 0.67 to 6.67 g COD/L day.
Higher methane yield was recorded when OMWW was co-digested with OMSW compared to that observed when OMWW was digested alone. The highest CH4 production of about 0.95 L/L day was reached at an OLR of 4.67 g COD/L day, while the maximum COD removal efficiency of 89% was achieved at the lowest OLR of 0.67 g COD/L day.
Ethanol production
OMSW could be a promising substrate for ethanol production due to their high cellulose and hemicellulose content (Battista et al. 2016; Fernandes et al. 2016). OMSW is, however, also rich in lignin known for their inhibitory effect on cellulase enzymes’ activity and saccharification process, which can reduce the efficiency of its conversion to ethanol (Ximenes et al. 2011). Several pretreatment methods including physical (e.g., microwave, ultrasound), chemical (e.g., alkali, dilute acid, ozonolysis, organosolvents) or physicochemical (e.g., steam explosion, hydrothermolysis, and wet oxidation) methods have been used in single or in combined processes to remove lignin from OMSW (Aguilar-Reynosa et al. 2017; Rosen et al. 2019; Peretz et al. 2021). The selection of a pretreatment method should be based primarily on its ability to provide enzymes access to cellulose allowing, hence, high concentrations of fermentable sugars, but should also be cost effective and limit the formation of fermentation inhibitors. Tayeh et al. (2020) reported that microwave treatment of OMSW in the presence of formic acid allowed highest saccharification rates (90% of cellulose fraction hydrolysis and 91.5 mg ethanol per gram OMSW) and important fermentation yield (15.9 g/L ethanol), while microwave with water treatment resulted in less saccharification and ethanol production (9.6 g/L). Fernandes et al. (2016) exploited the fermentation of extracted olive pomace after dilute acid hydrolysis pretreatment for bioethanol production. Although the adopted pretreatment significantly removed hemicellulose, the subsequent enzymatic treatments showed that the pretreated biomass still exhibited a significant recalcitrance to cellulase action, when compared to the equivalent material pretreated by autohydrolysis. A size reduction and an alkaline post-treatment of extracted olive pomace were tested for the improvement of enzymatic saccharification. The result showed that size reduction was more effective in reducing the lignin content and improving the enzymatic accessibility as compared to the alkaline post-treatment. In a study performed by Najafi et al. (2021), an integrated process regrouping fermentation, anaerobic digestion of fermentation residues, and lignin production was performed. In the same, study three different pretreatments have been tested, namely liquid hot water, organosolv, and acid-catalyzed organosolv. By using this combined process, authors reported a production of 295.5 L bioethanol, 137.2 m3 biomethane, and 347.1 kg lignin. The anaerobic treatment of waste streams resulting from ethanol production to provide biomethane and lignin improved the energy recovery of the whole plant up to 2.5 times as compared to single-product plants. Organosolv and acid-catalyzed organosolv have been reported improving ethanol and methanol production. Interestingly, the developed integrated process allowed an overall energy production per hectare of olive trees of about 521.6 L gasoline.
Ethanol production from OMWs could be a promising alternative to fossil energy sources. However, the production process was not found to be profitable despite the availability and low cost of raw materials (Christoforou and Fokaides 2016). Additional efforts are still needed to optimize the fermentation process and improve its efficiency in order to make ethanol derived from OMWs a more competitive product.
Biohydrogen production
OMWs, either fresh or stored, have also been reported as suitable feedstocks for biohydrogen production due to their content in organic substances, such as sugars, tannins, polyalcohols, pectins, lipids, and organic acids (Padovani et al. 2013). Biohydrogen is mainly produced by dark-fermentation or photo-fermentation or a sequential operation of both processes. Scoma et al. (2013) used a mesophilic packed bed biofilm reactors filled with ceramic cubes and inoculated with an acclimated acidogenic microbial consortium for biohydrogen production from dephenolized olive mill wastewater. The results showed that biohydrogen relative amount and productivity increased from 3 to 32% and from 0.20 to 6.10 dm3/m3 h, respectively, by decreasing the HRT from 7 to 1 day. In another study, Eroğlu et al. (2006) introduced two novel two-stage processes for hydrogen production from OMWW. In the first two-stage process, dark fermentation by activated sludge cultures followed by photofermentation process by Rhodobacter sphaeroides is involved leading to a promising hydrogen production potential of about 29 L H2/L OMWW. The hydrogen production using the second two-stage process, which involved a clay treatment step followed by photofermentation by R. sphaeroides O.U. 001 allowed a higher hydrogen production (35 L H2/L OMWW) and a promising COD conversion efficiency (52%). The results showed that both pretreatment processes enhanced the photofermentation process leading to promising hydrogen production even with highly concentrated OMWW. The simultaneous production of bioethanol and biohydrogen from OMWW-olive pomace mixture using Saccharomyces cerevisiae anaerobic fermentation was also investigated by Battista et al. (2016). Authors studied several pretreatments (ultrasonic pretreatment, basic pretreatment, and calcium carbonate addition) to improve glucose release and then enhance bioethanol and biohydrogen production and simultaneously reduce the inhibiting effect of polyphenols on the fermentation process. The results showed that all the pretreatment methods improved bioethanol and biohydrogen production yields, with basic and ultrasonic pretreatments resulted in the highest bioethanol and biohydrogen concentration, due to their contribution in improving the hydrolysis of lignin and cellulose and in increasing the soluble sugars (in particular glucose) content in the reaction mixture.
Application of OMWs in agriculture
Direct spreading of OMWs in soil
The use of OMWs for agricultural purposes has received a great deal of attention as a potential method for their valorization. Among several application routes, direct spreading of OMWs in soil was widely discussed, between those who supported their beneficial effect excluding any significant risk for crops and soil properties and those who showed negative effects in particular on surface and groundwater. The difference in the obtained results may be attributed to the difference in the experimental conditions used in each study, such as differences in the spreading method and doses, the type of soil and phonological stage of the crop and the climatic conditions. For optimal OMWs spreading that respect specific regulations, a proper amendment method and a rational use of OMWs should be applied. Regarding the spreading of OMWW, it has been reported that nitrogen (almost exclusively in organic form), potassium, phosphorus, magnesium, and organic matter present in OMWW can substitute some of the nutrients provided with chemical fertilizer and improve soil fertility (Regni et al. 2017). It was estimated that approximately 3000–6000 kg of dry organic matter, 25–50 kg of nitrogen, 15–30 kg of phosphorus, and 80–160 kg of potassium could be provided by spreading 80 m3 OMWW/s in soil (Di Giovacchino and Seghetti 1990). Fertigation with OMWW is preferably applied on clay–loam soils, characterized by their high cation-exchange capacity (Regni et al. 2017). OMWW has also been shown to increase the exchangeable potassium in a loamy clay soil and phosphorus in a red soil (Gioffré et al. 2004). OMWW spreading can cause slight changes in the soil pH due to its acidic character, which can also affect the mobility of macro- and micronutrients and the soil microbiological activity (IOOC 2004). However, the effect of OMWW spreading on soil pH was reported significantly reduced after few months, due to the production of ammonia resulting from the bacterial breakdown of OMWW organic matter and the buffering capacity of soil (Regni et al. 2017). The effect of OMWW spreading on soil microbiology is due not only to the variation in the soil pH, but also to the contribution of OMWW organic matter, which induces an increase in the soil microflora. Mekki et al. (2006a) reported a significant increase in soil actinomycetes, spore-forming bacteria and soil fungi and a significant reduction in the number of soil nitrifying bacteria. Similarly, Mechri et al. (2007) observed an increase in soil fungi, Gram-negative bacteria and actinomycetes after the addition of more than 30 m3 OMWW/ha and a significant decrease of Gram-positive bacteria after 1 year of OMWW application in a field of olive trees. Although the magnitude of the effect of OMWW application on soil microflora is different between different investigations, it is generally reported that OMWW amendment caused minor long-term effects on soil microflora and that no evidence of any inhibitory effect on the growth of soil microorganisms was recorded.
The application of OMWW as soil amendment has been reported as negatively affecting cultivated plants; this effect is mainly associated to OMWW application close to the sowing period and to the used dose (Bonari et al. 2001). For instance, an inhibition of wheat during the early stages of growth was observed, while no adverse effects were noticed at harvest (Boz et al. 2003). The toxicity of OMWs toward plants depend also on which part of the plant is in contact with OMWs. Tomato roots have been reported more sensitive to OMWs than tomato shoots (Ouzounidou et al. 2008). These effects may be associated to the lipophilicity of OMWs fatty acids and phenols, which limits the accessibility of nutrients inside the biological membranes (Saadi et al. 2007). The identification of phenolic compounds responsible on OMWs phytotoxicity was the subsect of many research studies. Isidori et al. (2005) while studying the effect of main OMWs phenolic compounds on watermelon, garden cress, and sorghum germination reported hydroxytyrosol and catechol as the responsible on the highest observed phytotoxicity effect. The same results were also reported by Aliotta et al. (2002) in regard to the germination of radish and durum wheat seeds. A dose-dependent phytotoxic effect of phenols on the germination of English cress and tomato was stated by Greco et al. (2006). In another study, Enaime et al. (2020a) showed that the phytotoxicity of OMWW anaerobically treated appears to be determined not only by the monomeric phenols but also by other toxic components unaffected by the anaerobic treatment.
OMSW spreading on agricultural surfaces has also been adopted as an operationally simple and economically feasible valorization method. The composition of pomace is relatively similar to that of organic amendments, and thus can be used for agronomic purposes (Toscano and Montemurro 2012). Other than being economical and easily practicable management method for olive mill operator, it has been reported conferring considerable benefits for soil characteristics and crops productivity. Kavdir and Killi (2007) demonstrated that soil amendment with pomace improves its water holding capacity, structure, and stability, making it less susceptible to erosion. The incorporation of olive pomace in soil increases its organic matter and enhanced its biological activity, without detectable negative effects on pH value and salinity (Regni et al. 2017; Innangi et al. 2017). The effect of pomace application on soil organic matter is strongly depending on the application method. Nasini et al. (2013) proceeded to the spreading of large amounts of pomace (50 t/ha) in an olive grove in central Italy for 4 consecutive years and reported an increase in organic matter content, total nitrogen, exchangeable potassium and magnesium, and available phosphorus and a slight decrease in pH. Soil amendment with olive pomace could be a valuable method to improve its fertility with costs lower than those required when using chemical fertilizers. Brunetti et al. (2005) observed in a field experiment an important increase in soil total nitrogen after 2 years of olive pomace application. Similarly, Proietti et al. (2015) reported a significant increase in soil available phosphorus in the first 15 cm of the treated soil; however, no effect was occurred in the 15–30 cm layer as compared to the control. Regarding the effect of olive pomace amendment on soil microbiology, Nasini et al. (2013) reported that olive pomace could be only a short-term substrate for soil microbiota recording no significant increase in the number of total microorganisms following the application of pomace. Authors also observed no difference between treated soil and the control when olive pomace is applied at the 15–30 cm dept, suggesting that environmental concerns related to the use of pomace as a soil amendment can be excluded considering that upper layer is not affected by olive pomace spreading. Soil amendment with olive pomace did not only affect soil properties but also crops productivity (Nasini et al. 2013). The application of wet olive pomace on a maize crop for 2 years allowed an increase in the production yield, grain gross protein, grain soluble carbohydrate content, and yield and number of grains per corncob (Tajada and Gonzalez 2004). An increase in the yield of winter wheat crop grown in greenhouse of up to 198% has also been observed by López-Piñeiro et al. (2006). The application of olive pomace as soil amendment on olive trees was also studied. Proietti et al. (2015) applied wet olive pomace on olive grove for 3 consecutive years and observed an increase of olive trees productivity without exhibiting a negative impact on olive oil quality. An enhancement in fruit growth and yield was also reported by Nasini et al. Nasini et al. (2013) when applying olive pomace on olive trees during 4 years without negative effects on the oil content. The positive effect of OMWs spreading on soil and crops is conditioned by the respect of the maximum spreading load and the correct spreading technique and time. López-Piñeiro et al. (2007) reported that the optimal spreading period is corresponding to the period before the resumption of vegetative growth. The spreading load could be higher when OMWs are applied on tree crops such as olive tree. Additionally, the nature of OMWs is also an important factor in determining the spreading load. In Italy, the agronomic use of OMWW derived from traditional extraction systems is allowed up to 50 m3/ha annually, while up to 80 m3/ha is allowed when OMWW is derived from modern extraction systems (Regni et al. 2017).
OMWs composting
Composting of OMWs, which allows the breakdown of labile organic compounds and the production of a material rich in organic matter, macro and micronutrients and free of phytotoxic elements, was reported beneficial for plant growth and effectively facilitate the integration of OMWs as organic amendment into the soil (Alburquerque et al. 2006). Co-composting of OMWs with other agricultural wastes, such as olive tree leaves, straw, cotton gin waste, grape stalks, and animal manures, has also been studied (Majbar et al. 2018; Cayuela et al. 2004). Compost and co-composts derived from OMWs have been effectively used as organic fertilizers for horticultural crops (Alburquerque et al. 2006), olive trees (Cayuela et al. 2004), and also as part of the substrate or growing media for ornamental plant culture (Garcia-Gomez et al. 2002). In Spain, compost from wet olive pomace is included, as an organic amendment, in the legislation on fertilizing products, which also specified the physico-chemical requirements of the product (Pardo et al. 2017). Although the results showing that composts derived from OMWs exhibited a satisfying degree of humification and no phytotoxic effect, OMWs themselves could be, however, difficult substrates for composting, due to their high moisture content (> 90% in OMWW) and to the presence of compounds, like fats and polyphenols, that exhibit an antimicrobial character (Ramos-Cormenzana et al. 1995). Moreover, the dense and sticky physical texture of OMSW especially TPOMW makes sometimes the aeration process hardly performed, which can lead to the formation of aggregates (Marks et al. 2020). This limitation has led to search for more cost-effective alternatives for the efficient application of OMWs in soil.
Application of OMWs-derived biochar/hydrochar as soil amendment
Conversion of OMWs into more stable carbon material before its application as soil amendment has been introduced as an alternative for their valorization. Pyrolysis of agro-residues and their conversion into biochar can fulfil the aim of closing the loop in agriculture and circular economy objectives in Mediterranean countries. Biochars generally produced by slow pyrolysis can be used to increase soil pH, electrical conductivity, available P and cation exchange capacity (Biederman and Harpole 2012; Marks et al. 2016). The alkaline character of biochar, their elevated concentration in Ca and Mg, and their sorption capacity can make them useful for remediation strategies, e.g. metal retention (Alburquerque et al. 2014). The application of biochar derived from OMWs to soil showed positive effects on plant growth by promoting the proliferation of fine root and facilitating water and nutrients retention (Olmo et al. 2014; Marks et al. 2020). OMWs conversion to biochar is also a good strategy for carbon sequestration, due to its high concentration in recalcitrant carbon showing low mineralization rates and long residence times to degradation; this capability is more pronounced for biochars derived from OS (Alburquerque et al. 2014; Olmo et al. 2014). As most lignocellulosic feedstocks, OMWs-derived biochars are, however, exhibiting low nitrogen contents (Table 2), which could limit its efficiency as fertilizer (Marks et al. 2020). Haddad et al. (2017) proceed to the impregnation of wood sawdust with OMWW in order to recover their nutrients content, followed by drying and slow pyrolysis. This strategy does in fact increase nitrogen content of the final biochar in addition to enriching it with macro- and micronutrients. OMWs-derived hydrochars are also valuable carbonaceous materials in agriculture for their slow carbon mineralization and high mineral contents (Kambo and Dutta 2015). Although biochar and hydrochar can be used in agriculture for similar purposes to improve soil structural, physico-chemical, and microbiological properties, their physicochemical properties are different (Table 2), because the reactions involved during the thermal process used for their production are different (Enaime et al. 2023). Hydrochar is generally exhibiting low pH as compared to OMWs-derived biochar (Table 2), due to the presence of organic acids generated during the reactions of dehydration and decarboxylation, which makes it more suitable for alkaline soils to lower their pH (Khosravi et al. 2022). Hydrochar is also characterized by a high density of phenolic, carboxylic, and aliphatic groups, in contrast to biochar produced by pyrolysis having few aliphatic groups and more aromatic structures, which makes of hydrochar more easily decomposable compared to biochar (Azzaz et al. 2020; Gascó et al. 2018). Moreover, the HTC liquid phase is a concentrate of some nutrients such as potassium but has so far not received an attention as a fertilizer (Marks et al. 2020).
Application of OMWs as biopesticide
Due to their phytotoxic and antimicrobial properties, OMWs have also been tested in agriculture as biopesticide for crops protection and as herbicide for weed control (Larif et al. 2013; Lykas et al. 2014; Boz et al. 2009). Boz et al. (2009) showed that olive pomace could be applied at a rate of 10 to 20 t/ha for adequate weed control and crop safety. OMWW was also used as an efficient alternative to commercial corrosive disinfectants such as sodium hypochlorite, due to its high content on phenolic compounds such as gallotannins, p-coumaric acid, and hydroxytyrosol, known for their antimicrobial effect and inhibiting effect on germination, growth, and development of different weeds (Doula et al. 2012; Lodhi 1976). A hydroxytyrosol-rich OMWW and a hydroxytyrosol-rich extract from fresh OMWW showed high fungicidal activities against Verticillium dahliae (Yangui et al. 2010). Compared to untreated plants, the incorporation of hydroxytyrosol-rich OMWW and hydroxytyrosol-rich extract into soil significantly reduced Verticillium wilt disease incidence by 86 and 83% and wilt severity by 86 and 84.5%, respectively. In another study, Yangui et al. (2009) observed an enhancement of germination percentage, root length, shoot height and shoot weight of tomato and muskmelon seed plants after the addition of hydroxytyrosol rich concentrate as a natural disinfectant at 10% (dw/v). The allelopathic effects of sterile water extracts of TPOMW and TPOMW composts on seed germination of highly invasive weeds, namely Amaranthus retroflexus L., Solanum nigrum L., Chenopodium album L., and Sorghum halepense (L.) Pers., have been studied by Cayuela et al. (2008). The results showed a substantially inhibition of Amaranthus retroflexus L. and Solanum nigrum L. germination by both TPOMW and immature TPOMW compost extracts, while an only partially reduction in the germination of Solanum nigrum L. using mature composts extracts has been observed. The authors claimed that the fungicidal capability of OMWs mature composts could be due to the presence of toxic metabolites (antibiosis) produced by some microbial communities during the composting process. In the same study, a significant hatch suppression was also showed by TPOMW composts, which was supposed to be due to the existence of bioactive compounds able to pass through the nematode eggshell. The use of OMWs-derived composts as a soil additive could also exert a biopesticidal action against plant pathogens due to their high content of nutrients and biocidal compounds (tannins and phenolic compounds), which stimulate root development and boost plant growth (Sasanelli et al. 2011). Oka and Yermiyahu (2002) suggested that the nematode suppressiveness of composts may be due to their high N–NH4 concentrations and high electrical conductivity values.
Livestock feeding with OMWs
Among the applications of OMWs in agriculture, the incorporation of OMWs into the diets of livestock has been also suggested as a strategy to minimizing both the costs related to OMWs management and those related to animal feeding, as animals become less dependent on conventional feeds such as cereal grains (Molina-Alcaide and Yáñez-Ruiz 2008). Researchers focused their studies to find alternative ways to reduce the content of saturated fatty acids in milk and meat due to their hypercholesterolemic and thrombogenic effects that could lead to cardiovascular diseases. The enrichment of diets with agro-industrial by-products, such as OMWs, has been reported as beneficial due to their high content in unsaturated fatty acids (Tzamaloukas et al. 2021). Molina-Alcaide et al. (2010) reported that the feeding of ruminants with olive pomace at 10% reduced the overall feeding cost and improved milk composition. In another study, Nasopoulou and Zabetakis (2013) reviewed that olive pomace could be exploited as an alternative dietary lipid source in compounded fish feeds for aquaculture and could also be incorporated in moderate consumption in animal feeds, without affecting animal performance while reducing saturated acids and enriching meat and milk with unsaturated fatty acids. Other investigations reported that the level of cholesterol and saturated fatty acids decreased and those of unsaturated fatty acids increased in egg yolk after OMWs incorporation (Afsari et al. 2014; Abd El-Samee and Hashish 2011). OMWW has also been used as a source of polyphenols additives to increase the antioxidant defense of productive animals. Several studies have been carried out to understand the effect of their addition to the diet of different animals such as broiler chickens and mammals on their antioxidant defense. Gerasopoulos and Petrotos (2022) analyzed the distribution of fatty acids in plasma and tissues of piglets alimented with feed containing polyphenols extracted from OMWW. The addition of polyphenols to the piglets feed allowed a decrease in omega-6/omega-3 ratio, which leads to more omega-3 fatty acids in the meat of pigs. In another study, Gerasopoulos et al. (2015) incorporated prefiltered OMWW into broilers’ feed and examined their antioxidant activity. The 24 broilers receiving feeds supplemented with OMWW were observed for 37 days, and bloods and tissues (muscle, heart, liver) samples were collected at different periods. Higher total antioxidant capacity in plasma and tissues was observed for broilers receiving feeds supplemented with OMWW along with a significantly lower protein oxidation and lipid peroxidation levels as compared to the control. Even with the well-documented benefits of OMWs addition in animal feeds, there are some barriers that limit their wider use, including their low content on protein and their counterproductive effect due to their high energy content, which can reduce the animals’ total feed intake. The respect of the optimal addition percentage (10% of total diet at most, although 5% is usually recommended) is then necessary to avoid any side effect and guarantee a balanced diet (Berbel and Posadillo 2018).
Application of OMWs for wastewater treatment
Biosorption has been proven as an effective and economically competitive process for wastewater treatment, especially when the biosorbent is derived from biowastes and agricultural by-products. Olive crops, which cover a global cultivated area of approx. 10 million hectares, are sources of huge amounts of low-cost and locally available waste materials that can be either directly exploited as biosorbent of organic and inorganic contaminants or used as precursors for biosorbents preparation. OS were effectively used for the biosorption of Alizarin Red S and methylene blue dyes from aqueous solution allowing maximum adsorption capacities of 16.10 mg/g and 13.20 mg/g, respectively (Albadarin and Mangwandi 2015). The authors reported that the adsorption rate is controlled by film diffusion in addition to the implication of adsorption mechanisms such as ion exchange and chelation. The ability of crude OS to adsorb iron from industrial wastewaters was also studied by Nieto et al. (2010). The equilibrium adsorption capacity was higher when the particles size decreased from 4.8 to < 1 mm. The percentage of iron adsorption increased from 30 to 70% when the initial concentration of biomass increased from 25 to 125 g/dm3. The optimum concentration of OS was fixed at 37.5 g/dm3. In another study (Banat et al. 2007), olive pomace after solvent extraction have been used in combination with charcoal produced from OMSW as an adsorbent for the removal of methylene blue from aqueous solutions in batch and fixed bed experiments. Batch experiment allowed to reach a dye removal efficiency of up to 80% using a sorbent concentration of 45 mg/mL and a greater dye removal has been observed as the olive pomace concentration increased. In the fixed bed adsorption experiment performed at bench scale, a significant increase in methylene blue uptake was observed using a mixture of olive pomace and charcoal in a multi-layer packed column. OMSW has also been used to remove heavy metals from industrial wastewater. Chouchene et al. (2014) reported a removal efficiency of Cu and Ni of 3.6 and 1.7 mg/g, respectively using OMSW, while Anastopoulos et al. (2015) showed that olive by-products could be effectively used to remove Pb and Cd at a pH range of 5–6, but less efficient in removing Cu, Cr, Zn, and particularly Ni.
The adsorption capacity of OMWs in removing some pollutants could be, however, not satisfactory in some cases due to their lower specific surface area and porosity. A modification of OMWs to improve their textural properties and adsorption capacities is then necessary. Thermochemical treatments, including pyrolysis, HTC, gasification, and torrefaction, are valid routes to convert biomass into renewable carbon materials with high adsorption capacities (Enaime et al. 2020b). Activated carbon (AC) derived from OMWs has been largely used as an adsorbent to remove organic and inorganic contaminants with a simple operating design (Hazzaa and Hussein 2015; Berrios et al. 2012). The preparation method and the experimental conditions affect significantly the final textural properties of the produced AC and hence its adsorption capacity. Enaime et al. (2017) explored the adsorption of indigo carmine dye from aqueous solution onto ACs prepared from OMSW impregnated with OMWW by chemical activation using potassium hydroxide and phosphoric acid as activation agents and physical activation using steam. The prepared ACs showed high removal efficiencies towards indigo carmine dye with that prepared by KOH chemical activation showing the highest adsorption capacity due to its higher micro- and mesoporous volume and its larger specific surface area. Other investigations also reported on the effectiveness of AC derived from exhausted olive-cakes (Baccar et al. 2009), olive peel and seed (Petrella et al. 2018), and raw olive stones (Hodaifa et al. 2013a) in removing heavy metals such as Pb2+, Cu2+, Fe3+, and Cr6+ from aqueous solutions.
Even if OMWs are an available biomass, the cost of their conversion into AC and the optimization of the preparation process to design an AC dedicated to the adsorption of a target molecule still limit its wide application on an industrial scale. Recently, several studies have highlighted the capacity of biochars and hydrochars as eco-friendly and low-cost alternative materials to successfully adsorb heavy metals, dyes and other organic pollutants from water and wastewater (Abdelhadi et al. 2017; Delgado-Moreno et al. 2021; Saleem et al. 2019). A concise review on different thermal conversion technologies and applications of char in wastewater treatment has been provided by Enaime et al. (2020b). The adsorption capacity of chars is strongly affected by the composition of the starting biomass, the production method, and the processing conditions, with temperature playing the key role. Abdelhadi et al. (2017) tested the adsorption efficiency of biochars produced from two- and three-phase OMSW from two different olive cultivars (Picual and Souri). Two-phase olive mill wastes derived from Picual cultivar and carbonized at 350 °C exhibited the best adsorption capacity. Authors suggested that even the biochar showed lower surface area (1.65–8.12 m2/g) as compared to commercial AC (1100 m2/g); its adsorption capacity towards Cu+2, Pb+2, Cd+2, Ni+2, and Zn+2 was more than 85% higher, suggesting that the surface area cannot be used as a sole predictor of heavy metal removal capacity and that other mechanisms related to the presence of functional groups on the surface of biochar could interfere. Izghri et al. (2020) proceeded to the preparation of hydrochars from TPOMW impregnated with FeCl3, which subsequently served as catalysts in advance oxidation process for the removal of methylene blue from aqueous solutions. According to Izghri et al. (2020), HTC of TPOMW at 250 °C during 4 h using a FeCl3 to TPOMW ratio of 1.5 allowed producing hydrochar with high mass yield (66%) and promising performances as a catalyst in heterogeneous Fenton-Like oxidation achieving 91% of methylene blue removal. The produced catalyst can be reused for successive cycles as it showed high stability and very less iron leaching properties. Delgado-Moreno et al. (2021) used pyrolysis and HTC to convert OMWs (OS, olive tree pruning, and pitted and reprocessed wet OMSW) into chars, which have been then used together with commercial biochars and a commercial AC as adsorbents to remove triclosan, ibuprofen and diclofenac from water. Despite of its low surface area (7.5 m2/g), hydrochar produced at 240 °C exhibited higher adsorption capacities (64% for diclofenac, 43% for ibuprofen and 98% for triclosan) due to its acidic pH and its surface rich in oxygenated functional groups.
Within the context of the circular economy, the use of OMSW in integration systems has also been proposed for the removal of polyphenols from OMWW. Allaoui et al. (2021) reported an adsorption capacity of about 381 mg/g of polyphenols from crude OMWW using crude OS as an adsorbent. Similarly, Stasinakis et al. (2008) tested the adsorption capacity of three different types of olive pomace, namely dried olive pomace, dried and solvent extracted olive pomace, and dried, solvent extracted, and incompletely combusted olive pomace. According to the results, dried, solvent extracted, and incompletely combusted olive pomace at a concentration of 10 g/L was able to remove more than 40% of polyphenols having an initial concentration of 50 mg/L, while showing a better stability as compared to the two other samples tending to release polyphenols. Authors also reported that fixed bed sorption experiments with lower flow rates and smaller particle size of sorbent resulted in longer column exhaustion time and higher initial removal efficiency. In another study, Enaime et al. (2019) successfully used OS as a filter media for the pretreatment of OMWW, achieving COD and polyphenols removal efficiencies of about 23.2% and 11.3%, respectively. Esteves et al. (2022) proceeded to the activation of olive stones and wood from olive tree pruning by physical (CO2) and chemical (KOH) methods for their subsequent use to remove OMWW phenolic compounds. Results showed that chemically activated olive stones present better performance (200 mg/g) than the physically activated sample (189 mg/g), due to its improved surface area and microporosity. Nevertheless, while the SBET increases from 792 to 1013 m2/g (i.e., ca. 28%), phenolic compound removal only improved by 5.8%, which is also an indicative that additional parameters should be considered. Authors also reported the possible thermal regeneration of the saturated adsorbents, while maintaining their performances. In another study, Abid et al. (2022) investigated the conversion of OMSW into a biochar that was used as an adsorbent for the removal and the recovery of polyphenols from OMWW. A maximum polyphenol adsorption of 140.5 mg/g was achieved with a high affinity of hydroxytyrosol to be recovered due to the polar nature of biochar surface. The adsorption capacity of biochar towards phenolic compounds is significantly influenced by the biochar surface charge, its surface area and pH and the abundance of carboxylic and lactonic functional groups. Hanandeh et al. (2021), while testing the efficiency of biochars derived from OMSW previously treated by FeCl3 and pyrolyzed at temperature of 550 °C for the removal of phenolic compounds from OMWW, achieved an adsorption capacity of about 103.9 mg/g at a pH of 2. Authors suggested that chemisorption is the dominating mechanism in the adsorption of phenolic compounds on biochar and that even the adsorption on the pre-treated biochar was 33% higher than the post-treated biochar; it is more economical to use post-treatment of the produced biochar with FeCl3 than the pretreatment of the starting biomass, as it reduces the use of FeCl3 by 75%.
OMWs as a source of bioactive components
The widely known benefits of olive oil is mainly due to their high content of bioactive molecules, which make it a product widely demanded by the consumer. These bioactive components are detected not only in olive oil but also at significant levels in its processing by-products, including OMWW and OMSW (Parkinson and Cicerale 2016). From these by-products, different bioactive molecules such as fatty acids, phenolic compounds, phytosterols, triterpenoids, tocopherols, and coloring pigments (chlorophylls and carotenoids) could be recovered. Some other bioactive compounds, like carotenoids or chlorophylls, have also been detected in olive oil extraction by-products but in low quantities (Hannachi et al. 2020; Otero et al. 2021). The concentration of bioactive molecules and their distribution in olive by-products varies depending on many factors including growth and climatic conditions, variety and maturity of olives, olive oil extraction method, and the by-product considered and its freshness (Romero et al. 2018). The storage of OMWs is a parameter that significantly affect their composition. For instance, an accumulation of hydroxytyrosol and a reduction of other monomeric and oligomeric phenolic components were reported as a result of the prolonged storage of OMWW (Feki et al. 2006).
Recently, more attention has been attributed to the reintegration of bioactive compounds recovered from OMWs in food and pharmaceutical industries and extensive studies have been performed to elucidate their chemical and biological properties and their biological properties. The different biological activities of OMWs-derived bioactive compounds, including antioxidant, anti-inflammatory, anticancer, and other activities, and the associated mechanisms were deeply reviewed by Otero et al. (2021). Biophenols constitute one of the major groups of bioactive compounds present in OMWs that are reported responsible for many biological activities. It is assumed that about 98% of the phenolic compounds present in olive fruit find their way to olive wastes, either in OMWW (approx. 53%) or in OMSW (approx. 45%) (Rodis et al. 2002). These hydrophilic components are mostly represented by phenyl alcohols, phenolic acids, secoiridoids, and flavonoid groups. Hydroxytyrosol, which is the main phenolic compound detected in OMWW, together with other simple phenols and flavonoids are reported for their high antioxidant activity, in addition to other activities such as cardioprotective and cancer preventing activities (Obied et al. 2005). Other bioactive compounds highly abundant in OMWs are oleosidic compounds resulting from the hydrolysis of oleuropein and its derivatives; it is assumed that about 80% of oleuropein contained in olive fruit is degraded during the olive oil extraction following the operations of crushing and malaxation (He et al. 2012). Oleosidic compounds and its derivatives are showing an important antibacterial activity, even higher than the well-studied oleuropein and many other simple phenols (Medina et al. 2007).
The diverse biological activities of OMWs bioactive compounds and their useful properties have created an interest in their extraction. The feasibility and efficiency of the recovery method are, however, the key factors for using these compounds as alternative natural antioxidants and antimicrobials. Several methods have been reported for the recovery of bioactive compounds from OMWs (Table 3). Liquid–liquid solvent extraction using organic solvents is typically the widely used technique for the extraction of bioactive compounds from different matrices. The organic solvents used provide a physical carrier for target compounds to be transported between different phases and then be recovered (Galanakis 2012). The nature of the solvent is an important factor affecting the extraction efficiency. Methanol–water mixtures have been effectively used for the extraction of phenols with high yields and widest arrays, while flavonoid aglycons have been effectively extracted using ethyl acetate (De Leonardis et al. 2007; Sannino et al. 2013). Other polar protic mediums like hydroalcoholic mixtures have been also used at different concentrations for the extraction of phenolic acids. The industrial application of bioactive compounds recovered by liquid–liquid extraction method could be however limited due to the toxicity and the inedibility of some solvents, raising then environmental, health, and safety concerns (Galanakis and Kotsiou 2017). Alternatively, bioactive compounds could be recovered by membrane filtration systems including micro-filtration, ultrafiltration, nanofiltration, and reverse osmosis. Servili et al. (2011a) proceeded to the recovery of hydrophilic phenols from fresh olive vegetable water in an industrial plant using a three-phase membrane system (microfiltration, ultrafiltration, and reverse osmosis) prior enzymatic treatment. This approach yielded a phenolic compounds-enriched concentrate that was effectively used for enriching the antioxidant content of virgin olive oil. Natural-based filters such as starch filters extracted from fruits, cereals, and tubers have also been used by Fernandez-Gutierrez et al. (2013) in a patented process for the extraction of bioactive compounds from olive oil by-products. Phenolic compounds were also separated from OMWs using different adsorbents such as AC and resins. For instance, Yangui and Abderrabba (2018) extracted total phenols (75.4%) and hydroxytyrosol (90.6%) from OMWW using AC coated with milk proteins. A high extraction yield (90%) of hydroxytyrosol from olive leaves has also been conducted using modified AC in batch and column systems through adsorption and desorption processes (Hadrich et al. 2022). Rubio-Senent et al. (2012) proceeded to the extraction of phenolic compounds by hydrothermal treatment of OMWs. This patented process promoted the breakdown of oleuropein, dimethyloleuropein, and verbascoside, which resulted in higher concentrations of hydroxytyrosol. Similarly, Lama-Muñoz et al. (2014) proceed to the recovery of antioxidant compounds from liquid fraction (prehydrolyzates) issued from autoclave treatment of olive stones at 130 ºC for 90 min followed by a dilute acid extraction (2% w/v sulfuric acid) to recover pentose sugars.
The emergent interest in the recovery of bioactive compounds increased the need to develop more efficient extraction technologies in order to reduce solvent consumption, shorten processing time, increase recovery yield, improve product quality, and enhance functionality of extracts, while lowering energy consumption as compared to conventional extraction methodologies (Rosello-Soto et al. 2015). New extraction technologies such as microwave assisted extraction, ultrasonic-assisted extraction, pressurized liquid extraction as well as electrotechnologies including high-voltage electrical discharges, ultrasound-assisted extraction, and others have also been introduced (Barba et al. 2015; Rosello-Soto et al. 2015; Galanakis 2021; Otero et al. 2021). In addition to being highly efficient, requiring low-energy consumption and short extraction time, these emerging technologies have the advantage of not involving high temperatures, which avoids damaging the structure of the extracted compound and helps preserving their bioactive content (da Rosa et al. 2021). Gómez-Cruz et al. (2021) proceeded to the extraction of phenolic compounds from exhausted olive pomace by microwave-assisted method using water as extraction solvent under different temperatures, extraction times, and solid loading conditions. The microwave-assisted extraction method at 99.7 °C, 3.9% (w/v) solids, and 34.3 min allowed for a maximum content of hydroxytyrosol (6 mg/g of exhausted olive pomace), which makes of the extract a potential alternative to be used as a functional and antioxidant additive. In another study, Niknam et al. (2021) used ultrasound-assisted extraction to extract phenolic compounds from dried and defatted olive pomace using 50% v/v ethanol–water as solvent. The extraction process yielded 14.70 mg/g total phenols, 2.48 mg/g total flavonoids, and 0.924 mmol Trolox/g antioxidant activity. A further treatment step using polymeric resins and activated charcoals followed by a desorption step using acidified ethanol–water has been used for the purification of the extracted biophenols. The overall process allowed a recovery of total phenols, hydroxytyrosol, and tyrosol of about 57.65%, 19.27%, and 45.73%, respectively. Other sustainable alternatives have also been studied. Sklavos et al. (2015) used solar distillation to simultaneously dry and recover antioxidant compounds from OMWW distillate. This system allowed, however, the recovery of only 4% of the initial phenols, with tyrosol present in all samples and hydroxytyrosol only in freshly collected samples. Further studies are then required to improve these findings.
Due to their antioxidant and antimicrobial properties, various applications of bioactive compounds derived from OMWs have been suggested (Table 3). The application of phenols in food industry is a promising alternative to mitigate the challenges associated to health problems related to the excessive use of synthetic antioxidants. By introducing olive leaves extracted phenols, mainly hydroxytyrosol and oleuropein aglycone, in refined olive oil and olive pomace oil, Bouaziz et al. (2010) reported a significant increase in the resistance of oils to oxidation. In the study of Lafka et al. (2011), OMWs-derived extracts were introduced in virgin olive oil and sunflower oil. Although its phenolic yield was not quite high, the tested extracts showed stronger antioxidant capacity than that observed by using BHT, ascorbyl palmitate, and vitamin E. In another study, Troise et al. (2014) reported that the addition of OMWW phenolic powder to ultra-pasteurized milk was able to trap the reactive carbonyl species such as hydroxycarbonyls and dicarbonyls and inhibit the formation of Maillard-derived off-flavor compounds during UHT treatment, which improved the nutritional and sensorial qualities of the milk. An extract from olive pomace was also used to substitute sulfur dioxide usually added to wine as a preservative and to prevent microorganisms’ proliferation (Ruiz et al. 2017). Exhibiting similar structures and mechanisms of action as synthetic compounds, OMWs-derived bioactive compounds, such as monounsaturated fatty acids, minerals and phenolic compounds could be applied in several pharmaceutical and cosmetic applications (Rodrigues et al. 2017). Their integration in creams, balms, shampoos, or hair conditioners was frequently used. Antioxidants such as hydroxytyrosol, oleuropein, caffeic acid, and flavonoids, are widely reported for their ability to mitigate the effects of skin ageing process, to scavenge oxidative substances and to act as UV blockers. The efficient application of phenolic compounds in cosmetic applications could be, however, limited due to their character of being very soluble in water, which promote their removal from the skin during seawater immersion.
Despite the high number of studies carried out for the recovery of bioactive compounds from OMWs and their reuse in different applications and the promising results obtained, most of them have been focused on the recovery of phenolic compounds. More research studies investigating the recovery and application of other bioactive compounds, such as monounsaturated fatty acids, are still needed.
Other applications of OMWs
OMWs have also attracted the building materials industry as low cost and available raw materials that can be used to replace or to be mixed with commercial products. OMWW issued from three-phase and two-phase olive oil extraction were used to replace freshwater in the manufacture of fired clay bricks (Mekki et al. 2006b). De la Casa et al. (2009) reported that the use of two-phase OMWW instead of freshwater in clay brick manufacture allowed the production of bricks with similar technological properties and extrusion performance as freshwater-based ones, with a simultaneous decrease in the heating requirement in the range of 2.4–7.3%. Incorporating OMWs into brick manufacturing is not only a promising disposal route for olive mills but can also bring economic benefits to the building materials industry by reducing the heat required during the brick production process. The water contained in OMWs is returned to the atmosphere during the drying of brick before their firing, while the solid matter remains locked in the bricks, which provides supplementary heat to the kiln during the firing stage (Mekki et al. 2006b). Silvestri et al. (2021) evaluated the technical feasibility and the environmental and economic sustainability of integrating OMWW in the fired clay brick production. Authors reported a decrease in global warming potential and in fossil fuels depletion of up to 3.1% and 4.3%, respectively, while no significant variations for the toxicity impact category were observed. Authors also reported that a beneficial use of OMWW in fired clay brick process should be associated to the installation of olive oil mills in a distance of less than 150 km from the brick factory (Silvestri et al. 2021). Several advantages have also been reported following the incorporation of olive pomace as an ingredient in ceramic manufacturing as compared to conventional ceramic products, including a 10% lower density and 18% lower thermal conductivity, in addition to an energy savings due to their organic matter content (Ruiz et al. 2017). Other application of OMWs have been also studied. The high concentration of OMWs in minerals, fatty acids and bioactive compounds, characterized by their moisturizer and antiaging properties, promotes their application in spa treatment (Rodrigues et al. 2017). OMWs could also be used as liquid growth medium for lipolytic microorganisms due to their content in residual oil that vary depending on the olive oil extraction process (Asses et al. 2009). Dye industry is another field of application of OMWs. OMWs characterized by their typical color could be a valuable source of natural dyes, which can serve as alternative synthetic dyes. Some research studies have been done to define the optimum conditions for the extraction of dyes from olive pomace with promissory results, while others studied the applicability of dyes derived from OMWs in textile industry (Meksi et al. 2012).
Issues related to OMWs management and barriers of the possible implantation of the proposed solution
Previously, OMWs treatment was not compulsory; thus, the most common and cheapest method of dealing with the large quantities of annually produced OMWs has been its disposal in open evaporation ponds or its draining in the environment at no cost for OMWW and its use as biofuel in boilers for OMSW, even the obtained energy yields are not satisfying. The absence of any obligation for olive mills to bear the disposal costs associated to the treatment of OMWs makes management methods based on resource recovery not attractive. However, the growing social awareness of environmental issues exerted pressure on governments to impose stricter laws and regulations in order to make OMWs treatments compulsory and preserve ecosystems. Besides the negative impact of the large produced amounts of hazardous by-products, olive oil production process is also criticized for its high energy consumption. The consideration of these two aspects makes the application of waste-to-resource concept in olive sector a promising solution. Olive mill solid and liquid wastes contain a significant energy content that can be recovered in different forms, 1 cm3 of OMWW could produce 60–80 kWh of energy in the form of biogas, while 1 kg of OMSW could be converted into 18,000 kJ of heat (Schmidt and Knobloch 2000). OMWs treatment aiming at energy recovery can therefore represent an interesting and sustainable alternative to partially meet the energy needs of oil mills. Moreover, OMWs could be used as additive in agricultural sector, as an adsorbent material for wastewater treatment, or as an attractive source of bioactive compounds.
Despite the large number of investigations having dealt with this topic, which in some points reported different findings, the opinion of the scientific community concerning the potential of OMWs as promising resources and the advantage of their optimal valorization is common. Though, several restrictions are still limiting the competitivity of the OMWs-derived resources and the scalability of the so far suggested solutions. The capability of OMWs-derived resources to create a positive economic balance is conditioned by the availability of the waste, the in-depth knowledge of its variable composition, and the simplicity and efficiency of the recovery technology. Moreover, the small dimensions of most olive mills and their spread-out distribution in the territory, in addition to their seasonal operation (limited to the period from November to February), make the calculation of the average annual waste production very uncertain and hamper the feasibility of larger centralized treatment plants and their continuous operation. Moreover, depending on the adopted trituration process, the olive variety, and the duration of storage, a high variety in OMWs properties could be expected, which make it impossible to apply a unique solution for their management. Taking all these variables into account makes it complicated to decide for a valuation method. The decision becomes more difficult considering that each method has its own advantages and disadvantages, and depending on the needs of the operator, the appropriate method may be different. For instance, although biological processes aimed at producing bioenergy from OMWs are mentioned as less expensive than other processes requiring complicated technologies, a great mastery of the treatment process is necessary, as it brings into contact microorganisms with phenolic compounds and lignin (in OMSW), known for their recalcitrant and antimicrobial properties. This makes the process start-up a critical phase that requires special attention. The complication of OMWs matrix, the presence of toxic compounds, and the potential formation of inhibiting intermediates could also reduce the production of biogas (Neshat et al. 2017). Concerning the safety of biogas production units, it is reported that biogas becomes flammable and can cause explosions when it comes into contact with O2. All these aspects require continuous control and monitoring of the process to avoid any risk of instability or unsafe situations, thus resulting in additional operating costs. Moreover, long retention times are generally required during anaerobic processes, which imply the need for large reactor volumes. This could be economically not attractive for olive mill operators. Hence, despite the technological progress achieved in using biochemical processes for energy production, the technology itself, when used for OMWs treatment, is still considered not mature yet to attract investors and be scaled up (Nunes et al. 2020). This makes the thermal processes more attractive. While adding OMWW to OMSW is counterproductive from the energy conversion point of view for dry thermal processes, it is advantageous for HTC processes. When comparing the energy saving of HTC and pyrolysis during the thermal treatment of OMWs with higher moisture content, it seems that HTC could be a promising method to convert OMWs into biofuel, with an energy saving of about 49% (Enaime et al. 2022). This is also beneficial for organizational and economic considerations, as no separate wastewater disposal will be required. Nevertheless, HTC process also requires optimization especially that HTC reactions are occurring at relatively high pressure. In addition, the process generates a liquid phase that could be considered as a concentrate of acids and different compounds, requiring additional treatments.
There is definitely a big need to explore the versatile bioactive compounds derived from OMWs and their treatment by-products and to introduce them in pharmaceutical, cosmetics, or even food industries, especially with the increasing interest of consumers for natural products. Even though the versatile composition of bioactive compounds derived from OMWs and their biological activities are very well known and their safety is also documented, the awareness of olive farmers on the importance and the potentialities of these compounds remains, however, very limited (Rodrigues et al. 2015). Olive farmers are the suppliers, and their involvement will guarantee the regular supply of interested industries. Moreover, the implementation of the policies is mainly focused on applications that mainly support bioenergy and biofuel production. One important reason behind this is the challenges related to economic aspects, as the recovery of bioactive compounds and their industrial application are mainly associated with high capital costs and complicated technologies that small olive oil industries could not support. In addition, considering environmental and health aspects, more sustainable extraction methods with reasonable investment should be adopted to reduce excessive use of potentially toxic solvents.
As summarized in Table 4, each OMWs valorization method has its specific limitations, but the most important limiting factor is the lack of government and community involvement and the absence of subsidies for investments to support the implementation of the proposed strategy. Although the various economic, social, and environmental benefits of waste recovery are recognized, there is still no practical support for this concept.
Based on the insights discussed above, the following policy recommendations, which involve all stakeholders, can be proposed:
-
Classification of olive oil extraction industries according to their size and waste production capacity in order to implement specific measures for the management of OMWs; separate facilities within the industry itself or creation of cooperatives at regional level for small olive mills.
-
Carrying out interviews with various stakeholders and field visits in order to analyze all political, legal, economic, social, geographical, and technical factors and create a database describing the specific need of each region.
-
Support scientific research and development, which can provide the fundamental bases of technological innovation in the field of OMWs valorization allowing to achieve satisfactory results.
-
Development of a network between scientists to facilitate communication and strengthen cooperation between them, which could avoid the inutile waste of time, resources, and expertise.
-
Establishment of specific policies to help olive oil producers and cooperatives adopt sustainable waste management practices; for instance, promoting dialogue with scientists, this will allow multiple stakeholders to be connected to research and entrepreneurial projects dedicated to OMWs valorization.
-
Governmental support of the waste-to-resources strategy in the olive sector through investment incentives and sustainable partnerships between public and private sectors.
Conclusion and prospects
Olive sector is committed to environmental obligations because of their unused high amounts and environmental harmful wastes. The growing awareness of the social community coupled with the legislative obligations has put increasing pressure on the olive industry to adopt new alternatives for the sustainable management of their wastes and byproducts. The implementation of the waste-to-resource concept will avoid the negative impact of OMWs, while producing new alternative resources, allowing the producers to diversify their activities and increase their capital. The data collected in this review shows that OMWs exhibit promising valorization potential from which different resources (biogas, biochar, activated carbon, bioactive compounds, soil conditioner, fertilizer, additive in construction materials…) could be recovered and reused in several sectors such as energy sector, agriculture, wastewater treatment, food and pharmaceutical industries, and construction industry. Although, this scientific evidence, a rational approach to OMWs valorization, has not been fully implemented. Several technological, organizational, and social factors are still required to allow converting OMWs into competitive resources able to create a positive economic balance. These include encouraging the continuous exchange and collaboration between industrial sector, including small olive oil extraction units, policy makers, and scientific research unities, increasing consumers’ awareness of the waste-to-resource concept and their environmental and socio-economic benefits, and strengthening the support of state through investment incentives and sustainable partnerships between public and private sectors.
This review contributes to an overall understanding of the different technologies that can be used for OMWs valorization within the waste-to-resources concept. However, most of the reported research studies are conducted in laboratory or in pilot scale; the results of these tests are not easily correlated to large-scale applications. More studies focused on large-scale plants in long-term operations are needed for the safe transfer of the research and development efforts into the industrial avenue. It is also crucial to perform techno-economic assessment of the various valorization choices at industrial scale to give an overall projection of the available potency and understand various scale-up issues. As some of the technologies suggested for OMWs valorization, such as biological processes, require a previous pretreatment, the focus of future research should be on designing pre-treatment strategies that will be able to withstand the inherent heterogeneity of OMWs composition. Preventive mechanisms should also be developed to avoid the long storage of OMWs resulting in possible oxidative loss of some of their bioactive compounds. It is also important to direct scientific efforts toward establishing combined processes rather than individual treatments for the valorization of OMWs to allow the management of all waste streams, even those produced during the valorization process itself. There is also a big gap in the integration of kinetic and statistical models for the optimization of these combined processes. These models could be useful for describing experimental systems and scaling them up.
Data availability
Data will be made available on request.
References
Abd El-Samee L, Hashish S (2011) Olive cake in laying hen diets for modification of yolk lipids. J Agric Sci Technol A 1:415–421
Abdelhadi S, Dosoretz C, Rytwo G, Gerchman Y, Azaizeh H (2017) Production of biochar from olive mill solid waste for heavy metal removal. Bioresour Technol 244:759–767
Abid N, Masmoudi M, Megdiche M, Barakat A, Ellouze M, Chamkha M, Ksibi M, Sayadi S (2022) Biochar from olive mill solid waste as an eco-friendly adsorbent for the removal of polyphenols from olive mill wastewater. Chem Eng Res Des 181:384–398
Afsari M, Mohebbifar A, Torki M (2014) Effects of dietary inclusion of olive pulp supplemented with probiotics on productive performance, egg quality and blood parameters of laying hens. Annu Res Rev Biol 4:198–211
Aguilar-Reynosa A, Romaní A, Rodríguez-Jasso R, Aguilar C, Garrote G, Ruiz H (2017) Microwave heating processing as alternative of pretreatment in second-generation biorefinery: an overview. Energ Convers Manag 136:50–65
Akar T, Tosun I, Kaynak Z, Ozkara E, Yeni O, Sahin EN, Akar ST (2009) An attractive agro-industrial by-product in environmental cleanup: dye biosorption potential of untreated olive pomace. J Hazard Mater 166:1217–1225
Albadarin A, Mangwandi C (2015) Mechanisms of alizarin red s and methylene blue biosorption onto olive stone by-product: isotherm study in single and binary systems. J Environ Manag 164:86–93
Alburquerque J, Gonzálvez J, García D, Cegarra J (2006) Composting of a solid olive mill by-product and the potential of the resulting compost for cultivating pepper under commercial conditions. Waste Manag 6:620–626
Alburquerque J, Calero J, Barrón V, Torrent J, del Campillo M, Gallardo A, Villar R (2014) Effects of biochars produced from different feedstocks on soil properties and sunflower growth. J Plant Nutr Soil Sci 177:16–25
Aliotta G, Fiorentino A, Oliva A, Temussi F (2002) Olive oil mill wastewater: isolation of polyphenols and their phytotoxicity in vitro. Allelopath J 9:9–17
Allaoui S, Bennani M, Ziyat H, Qabaqous O, Tijani N, Ittobane N, Hodaifa G (2021) Valorization of crude olive stone in the removing of polyphenols from crude olive mill wastewater: kinetic, isotherm and mechanism study. Heliyon 7:e075252
Al-Mallahi J, Furuichi T, Ishii K (2016) Appropriate conditions for applying NaOH-pretreated two-phase olive milling waste for codigestion with food waste to enhance biogas production. Waste Manag 48:430–439
Anastopoulos I, Massas I, Ehaliotis C (2015) Use of residues and by-products of the olive oil production chain for the removal of pollutants from environmental media: a review of batch biosorption approaches. J Environ Sci Health, Part A 50:677–718
Annab H, Fiol N, Villaescusa I, Essamri A (2019) A proposal for the sustainable treatment and valorisation of olive mill wastes. J Environ Chem Eng 7:102803
Armesto L, Bahillo A, Cabanillas A, Veijonen K, Otero J, Plumed A, Salvador L (2003) Co-combustion of coal and olive industry residues in fluidized bed. Fuel 82:993–1000
Asses N, Ayed L, Bouallagui H, Ben Rejeb I, Gargouri M, Hamdi M (2009) Use of Geotrichum candidum for olive mill wastewater treatment in submerged and static culture. Bioresour Technol 100:2182–2188
Atimtay A, Topal H (2004) Co-combustion of olive cake with lignite coal in a circulating fluidized bed. Fuel 83:859–867
Azbar N, Keskin T, Yuruyen A (2008) Enhancement of biogas production from olive mill effluent (OME) by co-digestion. Biomass Bioenergy 32:1195–1201
Azzaz A, Jeguirim M, Kinigopoulou V, Doulgeris C, Goddard ML, Jellali S, Ghimbeu CM (2020) Olive mill wastewater: from a pollutant to green fuels, agricultural and water source and bio-fertilizer–hydrothermal carbonization. Sci Total Environ 733:139314
Baccar R, Bouzid J, Feki M, Montiel A (2009) Preparation of activated carbon from Tunisian olive-waste cakes and its application for adsorption of heavy metal ions. J Hazard Mater 162:1522–1529
Banat F, Al-Asheh S, Al-Ahmad R, Bni-Khalid F (2007) Bench-scale and packed bed sorption of methylene blue using treated olive pomace and charcoal. Biores Technol 98:3017–3025
Barba F, Brianceau S, Turk M, Boussetta N, Vorobiev E (2015) Effect of alternative physical treatments (ultrasounds, pulsed electric fields, and high-voltage electrical discharges) on selective recovery of bio-compounds from fermented grape pomace. Food Bioproc Tech 8:1139–1148
Battista F, Mancini G, Ruggeri B, Fino D (2016) Selection of the best pretreatment for hydrogen and bioethanol production from olive oil waste products. Renew Energy 88:401–407
Benavente V, Fullana A (2015) Torrefaction of olive mill waste. Biomass Bioenerg 73:186–194
Benavente V, Fullana A, Berge N (2017) Life cycle analysis of hydrothermal carbonization of olive mill waste: comparison with current management approaches. J Clean Prod 142:2637–2648
Benincasa C, Torre CL, Plastina P, Fazio A, Perri E, Caroleo MC, Gallelli L, Cannataro R, Cione E (2019) Hydroxytyrosyl oleate: improved extraction procedure from olive oil and by-products, and in vitro antioxidant and skin regenerative properties. Antioxidants 233:8
Berbel J, Posadillo A (2018) Review and analysis of alternatives for the valorisation of agro-industrial olive oil by-products. Sustainability 10:237
Berrios M, Angeles M, Martın M (2012) Treatment of pollutants in wastewater: adsorption of methylene blue onto olive-based activated carbon. J Ind Eng Chem 18:780–784
Biederman L, Harpole W (2012) Biochar and its effects on plant productivity and nutrient cycling: a meta-analysis. GCB Bioenergy 5:202–214
Bonari E, Giannini C, Ceccarini L, Silvestri N, Tonini M, Sabbatini T (2001) Spargimento delle acque di vegetazione dei frantoi oleari sul terreno agrario. Inf Agrar 57:8–12
Borja R, Rincón B, Raposo F, Alba J, Martı́n A (2002) A study of anaerobic digestibility of two-phases olive mill solid waste (OMSW) at mesophilic temperature. Process Biochem 38:733–742
Bouaziz M, Feki I, Ayadi M, Jemai H, Sayadi S (2010) Stability of refined olive oil and olive-pomace oil added by phenolic compounds from olive leaves. Eur J Lipid Sci Technol 112:894–905
Boubaker F, Ridha BC (2007) Anaerobic co-digestion of olive mill wastewater with olive mill solid waste in a tubular digester at mesophilic temperature. Bioresour Technol 98:769–774
Boz O, Dogan M, Albay F (2003) Olive processing wastes for weed control. Weed Res 43:439–443
Boz O, Ogüt D, Kır K, Doğan M (2009) Olive processing waste as a method of weed control for okra, faba bean, and onion. Weed Technol 23:569–573
Brunetti G, Plaza C, Senesi N (2005) Olive pomace amendment in mediterranean conditions: effect on soil and humic acid properties and wheat (Triticum turgidum L.). J Agric Food Chem 53:6730–6737
Bruno AD, Romeo R, Piscopo A, Poiana M (2021) Antioxidant quantification in different portions obtained during olive oil extraction process in an olive oil press mill. J Sci Food Agric 101:1119–1126
Caballero AS, Romero-García JM, Castro E, Cardona CA (2020) Supercritical fluid extraction for enhancing polyphenolic compounds production from olive waste extracts. J Chem Technol Biotechnol 95:356–362
Cayuela M, Bernal M, Roig A (2004) Composting olive mill waste and sheep manure for orchard use. Compost Sci Util 12:130–136
Cayuela M, Millner P, Meyer S, Roig A (2008) Potential of olive mill waste and compost as biobased pesticides against weeds, fungi, and nematodes. Sci Total Environ 399:11–18
Chouchene A, Jeguirim M, Trouvé G (2014) Biosorption performance, combustion behavior, and leaching characteristics of olive solid waste during the removal of copper and nickel from aqueous solutions. Clean Techn Environ Policy 16:979–986
Christoforou E, Fokaides PA (2016) A review of olive mill solid wastes to energy utilization techniques. Waste Manag 49:346–363
da Rosa G, Martiny TR, Dotto GL, Vanga SK, Parrine D, Gariepy Y, Lefsrud M, Raghavan V (2021) Eco-friendly extraction for the recovery of bioactive compounds from Brazilian olive leaves. Sustain Mater Technol 28:e00276
De la Casa J, Lorite M, Jiménez J, Castro E (2009) Valorisation of wastewater from two-phase olive oil extraction in fired clay brick production. J Hazard Mater 169:271–278
De Leonardis A, Macciola V, Lembo G, Aretini A, Nag A (2007) Studies on oxidative stabilisation of lard by natural antioxidants recovered from olive-oil mill wastewater. Food Chem 100:998–1004
De Moraes Crizel T, de Oliveira Rios A, Alves DV, Bandarra N, Moldão-Martins M, Hickmann Flôres S (2018) Active food packaging prepared with chitosan and olive pomace. Food Hydro- Colloids 74:139–150
Delgado-Moreno L, Bazhari S, Gasco G, Méndez A, Azzouzi ME, Romero E (2021) New insights into the efficient removal of emerging contaminants by biochars and hydrochars derived from olive oil wastes. Sci Total Environ 752:141838
Di Giacomo G, Romano P (2022) Evolution of the olive oil industry along the entire production chain and related waste management. Energies 15:465
Di Giovacchino L, Seghetti L (1990) Lo smaltimento delle acque di vegetazione delle olive su terreno agrario destinato alla coltivazione di grano e mais. L’informatore Agrario 4:58–62
Donner M, Radic I (2021) Innovative circular business models in the olive oil sector for sustainable mediterranean agrifood systems. Sustainability 13:2588
Donner M, Radic I, Erraach Y, Hadad-Gauthier FE (2022) Implementation of circular business models for olive oil waste and by-product valorization. Resources 11:68
Doula MK, Tinivella F, Moreno Ortego LL, Kavvadias VA, Sarris A, Theocharopoulos S, Sanchez-Monedero MA, Elaiopoulos K (2012) Good practices for the agronomic use of olive mill wastes: application guide. PROSODOL Project (IFE07 ENV/GR/000280). Available online: http://www.prosodol.gr/sites/prosodol.gr/files/DGr_7.pdf. Accessed on 3 March 2019
Ducom G, Gautier M, Pietraccini M, Tagutchou JP, Lebouil D, Gourdon R (2020) Comparative analyses of three olive mill solid residues from different countries and processes for energy recovery by gasification. Renew Energy 145:180–189
Dutournié P, Jeguirim M, Khiari B, Goddard ML, Jellali S (2019) Olive mill wastewater: from a pollutant to green fuels, agricultural water source, and bio-fertilizer. Part 2: Water recovery. Water 11:768
El-Abbassi A, Saadaoui N, Kiai H, Raiti J, Hafidi A (2017) Potential applications of olive mill wastewater as biopesticide for crops protection. Sci Total Environ 576:10–21
Enaime G, Ennaciri K, Ounas A, Baçaoui A, Seffen M, Selmi T, Yaacoubi A (2017) Preparation and characterization of activated carbons from olive wastes by physical and chemical activation: application to indigo carmine adsorption. J Mater Environ Sci 8:4125–4137
Enaime G, Baçaoui A, Yaacoubi A, Wichern M, Lübken M (2019) Olive mill wastewater pretreatment by combination of filtration on olive stone filters and coagulation–flocculation. Environ Technol 40:2135–2146
Enaime G, Baçaoui A, Yaacoubi A, Belaqziz M, Wichern M, Lübken M (2020a) Phytotoxicity assessment of olive mill wastewater treated by different technologies: effect on seed germination of maize and tomato. Environ Sci Pollut Res 27:8034–8045
Enaime G, Baçaoui A, Yaacoubi A, Lübken M (2020b) Biochar for wastewater treatment—conversion technologies and applications. Appl Sci 10:3492
Enaime G, Baçaoui A, Yaacoubi A, Wichern M, Lübken M (2022) Hydrothermal carbonization of the filter bed remained after filtration of olive mill wastewater on olive stones for biofuel application. Biomass Convers Biorefin 12:1237–1247
Enaime G, Wichern M, Lübken M (2023) Contribution of biochar application to the promotion of circular economy in agriculture. Front Agron 5:1214012
Eroğlu E, Eroğlu İ, Gündüz U, Türker L, Yücel M (2006) Biological hydrogen production from olive mill wastewater with two-stage processes. Int J Hydrog 31:1527–1535
Esteves BM, Morales-Torres S, Madeira LM, Maldonado-Hódar FJ (2022) Specific adsorbents for the treatment of OMW phenolic compounds by activation of bio-residues from the olive oil industry. J Environ Manag 306:114490
Feki M, Allouche N, Bouaziz M, Gargoubi A, Sayadi S (2006) Effect of storage of olive mill wastewaters on hydroxytyrosol concentration. Eur J Lipid Sci Technol 108:1021–1027
Fernandes M, Torrado I, Carvalheiro F, Dores V, Guerra V, Lourenço P, Duarte L (2016) Bioethanol production from extracted olive pomace: dilute acid hydrolysis. Bioethanol 2:103–111
Fernandez-Gutierrez A, Segura-Carretero A, Lozano-Sanchez J (2013) Procedimiento para filtrar aceite usando tortas filtrantes de almidon nativo. Spain Patent ES 2374247:B1
Fernández-Rodríguez M, Rincon B, Fermoso F, Jimenez A, Borja R (2014) Assessment of two-phase olive mill solid waste and microalgae co-digestion to improve methane production and process kinetics. Bioresour Technol 157:263–269
Fernández-Rodríguez MJ, Mancilla-Leytón J, Jiménez-Rodríguez A, Borjaa R, Rincón B (2021) Reuse of the digestate obtained from the biomethanization of olive mill solid waste (OMSW) as soil amendment or fertilizer for the cultivation of forage grass (lolium rigidum var. wimmera). Sci Total Environ 792:148465
Fokaides P, Polycarpou P (2013) Exploitation of olive solid waste for energy purposes. In: Poullikkas A (ed) Renewable energy, economies, emerging technologies and global practices. Nova Science Publishers Inc., New York, pp 163–178
Fornes F, Belda RM, Lidon A (2015) Analysis of two biochars and one hydrochar from different feedstock: focus set on environmental, nutritional and horticultural considerations. J Clean Prod 86:40–48
Galanakis C (2012) Recovery of high added-value components from food wastes: conventional, emerging technologies and commercialized applications. Trends Food Sci Technol 26:68–87
Galanakis C (2021) Functionality of food components and emerging technologies. Foods 10:1–26
Galanakis C, Tsatalas P, Galanakis I (2018) Phenols from olive mill wastewater and other natural antioxidants as UV filters in sunscreens. Environ Technol Innov 9:160–168
Galanakis CM, Kotsiou K (2017) Recovery of bioactive compounds from olive mill waste. In: Galanakis CM (ed) Olive mill waste: recent advances for the sustainable management. Elsevier-Academic Press, London, pp 205–229
Galliou F, Markaki N, Fountoulakis MS, Nikolaidis N, Manios T (2018) Production of organic fertilizer from olive mill wastewater by combining solar greenhouse drying and composting. Waste Manag 75:305–311
Garcia-Gomez A, Bernal M, Roig A (2002) Growth of ornamental plants in two composts prepared from agroindustrial wastes. Bioresour Technol 83:81–87
Gascó G, Paz-Ferreiro J, Álvarez M, Saa A, Méndez A (2018) Biochars and hydrochars prepared by pyrolysis and hydrothermal carbonisation of pig manure. Waste Manag 79:395–403
Gerasopoulos K, Petrotos K (2022) Utilization of olive mill waste waters to produce bioactive animal feed. In: Membrane engineering in the circular economy: renewable sources valorization in energy and downstream processing in agro-food industry. Amsterdam: Elsevier, pp 393–412
Gerasopoulos K, Stagos D, Petrotos K, Kokkas S, Kantas D, Goulas P, Kouretas D (2015) Feed supplemented with polyphenolic byproduct from olive mill wastewater processing improves the redox status in blood and tissues of piglets. Food Chem Toxicol 86:319–327
Gigliotti G, Proietti P, Said-Pullicino D, Nasini L, Pezzolla D, Rosati L, Porceddu PR (2012) Co- composting of olive husks with high moisture contents: organic matter dynamics and compost quality. Int Biodeterior Biodegradation 67:8–14
Gioffré D, Cannavò S, Smorto D (2004) Risultati sugli effetti delle acque reflue olearie somministrate con diverse modalità su terreno ulivetato in pieno campo e su piante di olivo allevate in mastello. In: Valorizzazione di acque reflue e sottoprodotti dell’industria agrumaria e olearia, Laruffa, pp 81–98
Gómez-Cruz I, del Mar Contreras M, Romero I, Castro E (2021) Recovery of antioxidant compounds from exhausted olive pomace through microwave-assisted extraction. Biol Life Sci Forum 6:62
González-González A, Cuadros F (2014) Effect of aerobic pretreatment on anaerobic digestion of olive mill wastewater (OMWW): an ecoefficient treatment. Food Bioprod Process 95:339–345
Greco G, Colarieti M, Toscano G, Iamarino G, Rao M, Gianfreda L (2006) Mitigation of olive mill wastewater toxicity. J Agric Food Chem 54:6776–6782
Guinda A, Castellano JM, Santos-Lozano JM, Delgado-Hervas T, Gutierrez-Adanez P, Rada M (2015) Determination of major bioactive compounds from olive leaf. LWT - Food Sci Technol 64:431–438
Gunaya A, Karadag D (2015) Recent developments in the anaerobic digestion of olive mill effluents. Process Biochem 50:1893–1903
Haddad K, Jeguirim M, Jerbi B, Chouchene A, Dutournié P, Thevenin N, Ruidavets L, Jellali S, Limousy L (2017) Olive mill wastewater: from a pollutant to green fuels, agricultural water source and biofertilizer. ACS Sustain Chem Eng 5:8988–8996
Haddar W, Elksibi I, Meksi N, Mhenni MF (2014) Valorization of the leaves of fennel (Foeniculum vulgare) as natural dyes fixed on modified cotton: a dyeing process optimization based on a response surface methodology. Ind Crops Prod 52:588–596
Hadrich F, Geißen SU, Chamkha M, Sayadi S (2022) Optimizing the extraction conditions of hydroxytyrosol from olive leaves using a modified spherical activated carbon: a new experimental design. Biomed Res Int 17:6199627
Hanandeh AE, Albalasmeh A, Gharaibeh M, Alajlouni M (2021) Modification of biochar prepared from olive oil processing waste to enhance phenol removal from synthetic and olive mill wastewater. Sep Sci Technol 56:1659–1671
Hannachi H, Elfalleh W, Laajel M, Ennajeh I, Mechlouch R, Nagaz K (2020) Chemical profiles and antioxidant activities of leaf, pulp, and stone of cultivated and wild olive trees (Olea europaea L.). Int J Fruit Sci 20:350–370
Hazzaa R, Hussein M (2015) Adsorption of cationic dye from aqueous solution onto activated carbon prepared from olive stones. Environ Technol Innov 4:36–51
He J, Alister-Briggs M, de Lyster T, Jones G (2012) Stability and antioxidant potential of purified olive mill wastewater extracts. Food Chem 131(131):1312–1321
Hmid A, Mondelli D, Fiore S, Fanizzi FP, Chami ZA, Dumontet S (2014) Production and characterization of biochar from three-phase olive mill waste through slow pyrolysis. Biomass Bioenergy 71:330–339
Hodaifa G, Ochando-Pulido J, Ben Driss Alami S, Rodriguez-Vives S, Martinez-Ferez A (2013a) Kinetic and thermodynamic parameters of iron adsorption onto olive stones. Ind Crop Prod 49:526–534
Hodaifa G, Sánchez S, Martínez ME, Órpez R (2013b) Biomass production of Scenedesmus obliquus from mixtures of urban and olive-oil mill wastewaters used as culture medium. Appl Energy 104:345–352
Hytiris N, Kapellakis I, De R, Tsagarakis K (2004) The potential use of olive mill sludge in solidification process. Resour Conserv Recycl 40:129–139
Innangi M, Niro E, D’Ascoli R, Danise T, Proietti P, Nasini L, Regni L, Castaldi S, Fioretto A (2017) Effects of olive pomace amendment on soil enzyme activities. Appl Soil Ecol 119:242–249
IOOC (2004) Recycling of vegetable water & olive pomace on agricultural land (CFC/IOOC/04). Achievements of the project CFC/IOOC/04 “Recycling of vegetable water & olive pomace on agricultural land” Good practice in vegetable water and compost spreading on agricultural land: case of olive growing. Project executing agency CFC/IOOC/04 Agro-pôle Olivier ENA Meknès
Isidori M, Lavorgna M, Nardelli A, Parrella A (2005) Model study on the effect of 15 phenolic olive mill wastewater constituents on seed germination and vibrio fischeri metabolism. J Agric Food Chem 53:8414–8417
Izghri Z, Enaime G, Louarrat M, Gaini LE, Baçaoui A, Yaacoubi A (2020) Novel catalyst from two-phase olive mill wastes using hydrothermal carbonisation for the removal of methylene blue by heterogeneous Fenton-like oxidation. Int J Environ Anal Chem 100:854–872
Jeguirim M, Chouchène A, Réguillon AF, Trouvé G, Buzit GL (2012) A new valorisation strategy of olive mill wastewater: impregnation on sawdust and combustion. Resour Conserv Recycl 59:4–8
Kalmis E, Azbar N, Yildiz H, Kalyoncu F (2008) Feasibility of using olive mill effluent (OME) as a wetting agent during the cultivation of oyster mushroom, Pleurotus ostreatus, on wheat straw. Bioresour Technol 99:164–169
Kambo H, Dutta A (2015) A comparative review of biochar and hydrochar in terms of production, physico- chemical properties and applications. Renew Sustain Energy Rev 45:359–378
Kavdir Y, Killi D (2007) Influence of olive oil solid waste applications on soil pH, electrical conductivity, soil nitrogen transformations, carbon content and aggregate stability. Bioresour Technol 99:2326–2332
Khosravi A, Zheng H, Liu Q, Hashemi M, Tang Y, Xing B (2022) Production and characterization of hydrochars and their application in soil improvement and environmental remediation. Chem Eng J 430:133142
Lafka TI, Lazou A, Sinanoglou V, Lazos E (2011) Phenolic and antioxidant potential of olive oil mill wastes. Food Chem 125:92–98
Lama-Muñoz A, Romero-García J, Cara C, Moya M, Castro E (2014) Low energy-demanding recovery of antioxidants and sugars from olive stones as preliminary steps in the biorefinery context. Ind Crops Prod 60:30–38
Larif M, Zarrouk A, Soulaymani A, Elmidaoui A (2013) New innovation in order to recover the polyphenols of olive mill wastewater extracts for use as a biopesticide against the Euphyllura olivina and Aphis citricola. Res Chem Intermed 39:4303–4313
Lodhi A (1976) Role of allelopathy as expressed by dominating trees in a lowland forest in controlling the productivity and patterns of herbaceous growth. Am J Bot 63:1–8
López F, Pinzi S, Ruiz J, López A, Dorado M (2010) Economic viability of the use of olive tree pruning as fuel for heating systems in public institutions in south Spain. Fuel 89:1386–1391
López-Piñeiro A, Fernández J, Nunes R, Manuel J, García Navarro A (2006) Response of soil and wheat crop to the application of two-phase olive mill waste to Mediterranean agricultural soils. Soil Sci 171:728–736
López-Piñeiro A, Murillo S, Barreto C, Muñoz A, Rato J, Albarrán A, García A (2007) Changes in organic matter and residual effect of amendment with two-phase olive mill waste on degraded agricultural soils. Sci Total Environ 378:84–89
Lykas C, Vagelas I, Gougoulias N (2014) Effect of olive mill wastewater on growth and bulb production of tulip plants infected by bulb diseases. Span J Agric Res 12:233
Majbar Z, Lahlou K, Abbou MB, Ammar E, Triki A, Abid W, Nawdali M, Bouka H, Taleb M, Haji ME, Rais Z (2018) Co-composting of olive mill waste and wine-processing waste: an application of compost as soil amendment. J Chem 2018:7918583
Makri S, Kafantaris I, Savva S, Ntanou P, Stagos D, Argyroulis I, Kotsampasi B, Christodoulou V, Gerasopoulos K, Petrotos K, Komiotis D, Kouretas D (2018) Novel feed including olive oil mill wastewater bioactive compounds enhanced the redox status of lambs. In Vivo 32:291–302
Maragkaki A, Vasileiadis I, Fountoulakis M, Kyriakou A, Lasaridi K, Manios T (2018) Improving biogas production from anaerobic co-digestion of sewage sludge with a thermal dried mixture of food waste, cheese whey and olive mill wastewater. Waste Manag 71:644–651
Markou G, Georgakakis D (2010) Balanced waste management of 2- and 3-phase olive oil mills in relation to the seed oil extraction plant. Terr Aquat Environ Toxicol 4:109–112
Marks E, Mattana S, Alcañiz J, Pérez-Herrero E, Domene X (2016) Gasifier biochar effects on nutrient availability, organic matter mineralization, and soil fauna activity in a multi-year mediterranean trial. Agric Ecosyst Environ 215:30–39
Marks E, Kinigopoulou V, Akrout H, Azzaz A, Doulgeris C, Jellali S, Rad C, Sánchez Zulueta P, Tziritis E, El-Bassi L, Matei Ghimbeu C, Jeguirim M (2020) Potential for production of biochar-based fertilizers from olive mill waste in mediterranean basin countries: an initial assessment for Spain, Tunisia, and Greece. Sustainabilit 12:6081
Martins D, Martins RC, Braga MEM (2021) Biocompounds recovery from olive mill wastewater by liquid-liquid extraction and integration with Fenton’s process for water reuse. Environ Sci Pollut Res 28:29521–29534
Massadeh MI, Modallal N (2008) Ethanol production from olive mill wastewater (OMW) pretreated with Pleurotus sajor-caju. Energy Fuels 22:150–154
Mata-Alvarez J, Dosta J, Romero-Güiza M, Fonoll X, Peces M, Astals S (2014) A critical review on anaerobic co-digestion achievements between 2010 and 2013. Renew Sust Energ Rev 36:412–427
Mechri B, Echbili A, Issaoui M, Braham M, Elhadj S, Hammami M (2007) Short-term effects in soil microbial community following agronomic application of olive mill wastewaters in a field of olive trees. Appl Soil Ecol 36:216–223
Medina E, Brenes M, Romero C, Garcia A, de Castro A (2007) Main antimicrobial compounds in table olives. J Agric Food Chem 55:9817–9823
Mekki A, Dhouib A, Sayadi S (2006a) Changes in microbial and soil properties following amendment with treated and untreated olive mill wastewater. Microbiol Res 161:93–101
Mekki H, Anderson M, Amar E, Skerratt G, BenZina M (2006b) Olive oil mill waste water as a replacement for fresh water in the manufacture of fired clay bricks. J Chem Technol Biotechnol 81:1419–1425
Meksi N, Haddar W, Hammami S, Mhenni M (2012) Olive mill wastewater: a potential source of natural dyes for textile dyeing. Ind Crops Prod 40:103–109
Messineo A, Maniscalco MP, Volpe R (2020) Biomethane recovery from olive mill residues through anaerobic digestion: a review of the state of the art technology. Sci Total Environ 703:135508
Michailides M, Christou G, Akratos CS, Tekerlekopoulou AG, Vayenas DV (2011) Composting of olive leaves and pomace from a three-phase olive mill plant. Int Biodeterior Biodegradation 65:560–564
Mikdame H, Kharmach E, Mtarfi N, Alaoui K, Ben Abbou M, Rokni Y, Majbar Z, Taleb M, Rais Z (2020) By-products of olive oil in the service of the deficiency of food antioxidants: the case of butter. J Food Qual 2020:1–10
Molina-Alcaide E, Yáñez-Ruiz D (2008) Potential use of olive by-products in ruminant feeding: a review. Anim Feed Sci Technol 147:247–264
Molina-Alcaide E, Morales-García E, Martín-García A, Ben Salem H, Nefzaoui A, Sanz-Sampelayo M (2010) Effects of partial replacement of concentrate with feed blocks on nutrient utilization, microbial N flow, and milk yield and composition in goats. J Dairy Sci 93:2076–2087
Morillo JA, del Aguila VG, Aguilera M, Ramos-Cormenzana A, Monteoliva-Sanchez M (2007) Production and characterization of the exopolysaccharide produced by Paenibacillus jamilae grown on olive mill-waste waters. World J Microbiol Biotechnol 23:1705–1710
Murray A, Skene K, Haynes K (2015) The circular economy: An interdisciplinary exploration of the concept and application in a global context. J Bus Ethics 140:369–380
Naghmouchi I, Mutjé P, Boufi S (2015) Olive stones flour as reinforcement in polypropylene composites: a step forward in the valorization of the solid waste from the olive oil industry. Ind Crops Prod 72:183–191
Naisse C, Alexis M, Plante A, Wiedner K, Glaser B, Pozzi A, Carcaillet C, Criscuoli I, Rumpel C (2013) Can biochar and hydrochar stability be assessed with chemical methods? Org Geochem 60:40–44
Najafi E, Castro E, Karimi K (2021) Biorefining for olive wastes management and efficient bioenergy production. Energy Convers Manag 244:114467
Nakilcioğlu-Taş E, Ötleş S (2019) The optimization of solid–liquid extraction of polyphenols from olive stone by response surface methodology. J Food Meas Charact 13:1497–1507
Nasini L, Gigliotti G, Balduccini M, Federici E, Cenci G, Proietti P (2013) Effect of solid olive-mill waste amendment on soil fertility and olive (Olea europaea l.) tree activity. Agric Ecosyst Environ 164:292–297
Nasopoulou C, Zabetakis I (2013) Agricultural and aquacultural potential of olive pomace a review. J Agric Sci 5:116–127
Neshat S, Mohammadi M, Najafpour G, Lahijani P (2017) Anaerobic co-digestion of animal manures and lignocellulosic residues as a potent approach for sustainable biogas production. Renew Sust Energ Rev 79:308–322
Niaounakis M, Halvadakis C (2006) Olive processing waste management: literature review and patent survey. Typothito Publ., Athens, p 48
Nieto LM, Alami SBD, Hodaifa G, Faur C, Rodríguez S, Giménez JA, Ochando J (2010) Adsorption of iron on crude olive stones. Ind Crops Prod 32:467–471
Niknam SM, Kashaninejad M, Escudero I, Sanz MT, Beltrán S, Benito JM (2021) Valorization of olive mill solid residue through ultrasound-assisted extraction and phenolics recovery by adsorption process. J Clean Prod 316:128340
Nikolaou A, Kourkoutas Y (2018) Exploitation of olive oil mill wastewaters and molasses for ethanol production using immobilized cells of Saccharomyces cerevisiae. Environ Sci Pollut Res 25:7401–7408
Ntaikou I, Kourmentza C, Koutrouli E, Stamatelatou K, Zampraka A, Kornaros M, Lyberatos G (2009) Exploitation of olive oil mill wastewater for combined biohydrogen and biopolymers production. Bioresour Technol 100:3724–3730
Ntougias S, Bourtzis K, Tsiamis G (2013) The microbiology of olive mill wastes. BioMed Res Int 2013(784591):16
Nunes L, Loureiro L, Sá L, Silva H (2020) Thermochemical conversion of olive oil industry waste: circular economy through energy recovery. Recycling 5:12
Nunzioa MD, Picone G, Pasini F, Cabonia MF, Gianotti A, Bordoni A, Capozzi F (2018) Olive oil industry by-products. Effects of a polyphenol-rich extract on the metabolome and response to inflammation in cultured intestinal cell. Food Res Int 113:392–400
Obied H, Allen M, Bedgood D, Prenzler P, Robards K, Stockmann R (2005) Bioactivity and analysis of biophenols recovered from olive mill waste. J Agric Food Chem 53:823–837
Oka Y, Yermiyahu U (2002) Suppressive effects of composts against the root-knot nematode Meloidogyne javanica on tomato. Nematology 4:891–898
Olmo M, Alburquerque J, Barrón V, del Campillo M, Gallardo A, Fuentes M, Villar R (2014) Wheat growth and yield responses to biochar addition under mediterranean climate conditions. Biol Fert Soils 50:1177–1187
Otero P, Garcia-Oliveira P, Carpena M, Barral-Martinez M, Chamorro F, Echave J, Garcia-Perez P, Cao H, Xiao J, Simal-Gandara J, Prieto M (2021) Applications of by-products from the olive oil processing: revalorization strategies based on target molecules and green extraction technologies. Trends Food Sci Technol 116:1084–1104
Ouzounidou G, Asfi M, Sotirakis N, Papadopoulou P, Gaitis F (2008) Olive mill waste-water triggered changes in physiology and nutritional quality of tomato (Lycopersicon esculentum Mill.) depending on growth substrate. J Hazard Mater 158:523–530
Padovani G, Pintucci C, Carlozzi P (2013) Dephenolization of stored olive-mill wastewater, using four different adsorbing matrices to attain a low-cost feedstock for hydrogen photo-production. Bioresour Technol 138:172–179
Pardo T, Bernal P, Clemente R (2017) The use of olive mill waste to promote phytoremediation. In: Galanakis CM (ed) Olive mill waste: recent advances for the sustainable management. Elsevier-Academic Press, London, pp 183–204
Parkinson L, Cicerale S (2016) The health benefiting mechanisms of virgin olive oil phenolic compounds. Molecules 21:1–12
Pattara C, Cappelletti G, Cichelli A (2010) Recovery and use of olive stones. Commodity, environmental and economic assessment. Renew Sustain Energy Rev 14:1484–1489
Peña D, Fernández D, Albarrán A, Gómez S, Martín C, Sánchez-Terrón J, Vicente L, López-Piñeiro A (2022) Using olive mill waste compost with sprinkler irrigation as a strategy to achieve sustainable rice cropping under mediterranean conditions. Agron Sustain Dev 42:36
Peretz R, Mamane H, Wissotzky E, Sterenzon E, Gerchman Y (2021) Making cardboard and paper recycling more sustainable - recycled paper sludge for energy production and water-treatment applications. Waste Biomass Valori 12:1599–1608
Petrella A, Spasiano D, Acquafredda P, De Vietro N, Ranieri E, Cosma P, Rizzi V, Petruzzelli V, Petruzzelli D (2018) Heavy metals retention (Pb(II), Cd(II), Ni(II)) from single and multimetal solutions by natural biosorbents from the olive oil milling operations. Process Saf Environ Protect 114:79–90
Plaza A, Tapia X, Yañez C, Vilches F, Candia O, Cabezas R, Romero J (2020) Obtaining hydroxytyrosol from olive mill waste using deep eutectic solvents and then supercritical CO2. Waste Biomass Valorization 11:6273–6284
Poerschmann J, Baskyr I, Weiner B, Koehler R, Wedwitschka H, Kopinke FD (2013) Hydrothermal carbonization of olive mill wastewater. Bioresour Technol 133:581–588
Proietti P, Federici E, Fidati L, Scargetta S, Massaccesi L, Nasini L, Regni L, Ricci A, Cenci G, Gigliotti G (2015) Effects of amendment with oil mill waste and its derived-compost on soil chemical and microbiological characteristics and olive (olea europaea l.) productivity. Agric Ecosyst Environ 207:51–60
Rahmanian N, Jafari SM, Wanib TA (2015) Bioactive profile, dehydration, extraction and application of the bioactive components of olive leaves. Trends Food Sci Technol 42:150–172
Ramos-Cormenzana A, Monteoliva-Sanchez M, Lopez M (1995) Bioremediation of alpechin. Int Biodeterior Biodegrad 35:249–268
Regni L, Gigliotti G, Nasini L, Agrafioti E, Galanakis CM, Proietti P (2017) Reuse of olive mill waste as soil amendment. In: Galanakis CM (ed) Olive mill waste: recent advances for the sustainable management. Elsevier-Academic Press, London, pp 97–117
Rincon B, Borja R, Gonzalez J, Portillo M, Saiz-Jimenez C (2008) Influence of organic loading rate and hydraulic retention time on the performance, stability and microbial communities of one-stage anaerobic digestion of two-phase olive mill solid residue. Biochem Eng J 40:253–261
Rodis PS, Karathanos V, Mantzavinou A (2002) Partitioning of olive oil antioxidants between oil and water phases. J Agric Food Chem 50:596–601
Rodrigues F, da Mota Nunes MA, Pinto Oliveira MBP (2017) Applications of recovered bioactive compounds in cosmetics and health care products. In: Galanakis CM (ed) Olive mill waste: recent advances for the sustainable management. Elsevier-Academic Press, London, pp 255–274
Rodrigues F, Pimentel F, Oliveira M (2015) Olive by-products: challenge application in cosmetic industry. Ind Crops Prod 70:116–124
Romero C, Medina E, Mateo M, Brenes M (2018) New by-products rich in bioactive substances from the olive oil mill processing. J Sci Food Agric 98:225–230
Romero-García JM, Sanchez A, Rendón-Acosta G, Martínez-Patiño JC, Ruiz E, Magaña G, Castro E (2016) An olive pruning biorefinery for co-producing high value-added bioproducts and biofuels: economic and energy efficiency analysis. Bioenerg Res 9:1070–1086
Rosello-Soto E, Koubaa M, Moubarik A, Lopes R, Saraiva J, Boussetta N, Grimi N, Barba F (2015) Emerging opportunities for the effective valorization of wastes and by-products generated during olive oil production process: non-conventional methods for the recovery of high-added value compounds. Trends Food Sci Technol 45:296–310
Rosen Y, Mamne H, Gerchman Y (2019) Short ozonation of lignocellulosic waste as energetically favorable pretreatment. BioEnergy Res 12:292–301
Rubio-Senent F, Rodríguez-Gutíerrez G, Lama-Muñoz A, Fernández-Bolaños J (2012) New phenolic compounds hydrothermally extracted from the olive oil byproduct alperujo and their antioxidative activities. J Agric Food Chem 60:1175–1186
Ruiz E, Romero-García J, Romero I, Manzanares P, Negro M, Castro E (2017) Olive-derived biomass as a source of energy and chemicals. Biofuels. Bioprod Bioref 11:1077–1094
Ryan D, Prenzler PD, Lavee S, Antolovich M, Robards K (2003) Quantitative changes in phenolic content during physiological development of the olive (Olea europaea) cultivar hardy’s mammoth. J Agric Food Chem 51:2532–2538
Saadi I, Laor Y, Raviv M, Medina S (2007) Land spreading of olive mill wastewater: effects on soil microbial activity and potential phytotoxicity. Chemosphere 66:75–83
Saleem J, Shahid U, Hijab M, Mackey H, McKay G (2019) Production and applications of activated carbons as adsorbents from olive stones. Biomass Convers Biorefin 9:775–802
Sánchez-Gutiérrez M, Bascón-Villegas I, Espinosa E, Carrasco E, Pérez-Rodríguez F, Rodríguez A (2021) Cellulose nanofibers from olive tree pruning as food packaging additive of a biodegradable film. Foods 10:1584
Sannino F, De Martino A, Capasso R, El Hadrami I (2013) Valorisation of organic matter in olive mill wastewaters: recovery of highly pure hydroxytyrosol. J Geochem Explor 129:34–39
Sar T, Akbas MY (2022) Potential use of olive oil mill wastewater for bacterial cellulose production. Bioengineered 13:7659–7669
Sasanelli N, D’Addabbo T, Mancini L (2011) Suppressive effect of composted olive mill wastes soil amendments on the root-knot nematode Meloidogyne incognita. Acta Hortic 914:229–231
Schmidt A, Knobloch M (2000) Olive oil-mill residues: the demonstration of an innovative system to treat wastewater and to make use of generated bioenergy and solid remainder. In: Proceedings of the 1st World Conference on Biomass for Energy and Industry, Seville, pp 452–454
Scoma A, Bertin L, Fava F (2013) Effect of hydraulic retention time on biohydrogen and volatile fatty acids production during acidogenic digestion of dephenolized olive mill wastewaters. Biomass Bioenergy 48:51–58
Serrano A, Fermoso FG, Alonso-Fariñas B, Rodríguez-Gutierrez G, Fernandez-Bolaños J, Borja R (2017) Olive mill solid waste biorefinery: high-temperature thermal pre-treatment for phenol recovery and biomethanization. J Clean Prod 148:314–323
Servili M, Esposto S, Veneziani G, Urbani S, Taticchi A, Maio I (2011a) Improvement of bioactive phenol content in virgin olive oil with an olive-vegetation water concentrate produced by membrane treatment. Food Chem 124:1308–1315
Servili M, Rizzello C, Taticchi A, Esposto S, Urbani S, Mazzacane F, Di Maio I, Selvaggini R, Gobbetti M, Di Cagno R (2011b) Functional milk beverage fortified with phenolic compounds extracted from olive vegetation water, and fermented with functional lactic acid bacteria. Int J Food Microbiol 147:45–52
Shah F, Mahmood Q, Rashid N, Pervez A, Raja I, Shah M (2015) Co-digestion, pretreatment and digester design for enhanced methanogenesis. Renew Sust Energ Rev 42:627–642
Silvestri L, Forcina A, Di Bona G, C.S., (2021) Circular economy strategy of reusing olive mill wastewater in the ceramic industry: how the plant location can benefit environmental and economic performance. J Clean Prod 326:129388
Simonato B, Trevisan S, Tolve R, Favati F, Pasini G (2019) Pasta fortification with olive pomace: effects on the technological characteristics and nutritional properties. LWT–Food Sci Technol 114:108368
Sklavos S, Gatidou G, Stasinakis A, Haralambopoulos D (2015) Use of solar distillation for olive mill wastewater drying and recovery of polyphenolic compounds. J Environ Manag 162:46–52
Stasinakis A, Anastasios I, Constantinos VP, Halvadakis P (2008) Removal of total phenols from olive-mill wastewater using an agricultural by-product, olive pomace. J Hazard Mater 160:408–413
Tajada M, Gonzalez J (2004) Effects of application of a by-product of the two-step olive oil mill process on maize yield. Agron 96:692–699
Tarf OJ, Akça MO, Donar YO, Bilge S, Turgay OC, Sınağ A (2022) The short-term effects of pyro-and hydrochars derived from different organic wastes on some soil properties. Biomass Convers Biorefin 12:129–139
Tayeh HA, Azaizeh H, Gerchman Y (2020) Circular economy in olive oil production – olive mill solid waste to ethanol and heavy metal sorbent using microwave pretreatment. Waste Manag 113:321–328
Topal H, Atimtay A, Durmaz A (2003) Olive cake combustion in a circulating fluidized bed. Fuel 82:1049–1056
Toscano P, Montemurro F (2012) Olive mill by-products management. In: Olive germplasm—the olive cultivation, table olive and olive oil industry in Italy. InTech Open Access Publisher, pp 1–384
Troise A, Fiore A, Colantuono A, Kokkinidou S, Peterson D, Fogliano V (2014) Effect of olive mill wastewater phenol compounds on reactive carbonyl species and Maillard reaction end-products in ultrahigh-temperature-treated milk. J Agric Food Chem 62:10092–10100
Tzamaloukas O, Neofytou M, Simitzis P (2021) Application of olive by-products in livestock with emphasis on small ruminants: implications on rumen function, growth performance, milk and meat quality. Animals 11:531
Uddin MA, Siddiki SYA, Ahmed SF, Rony ZI, Chowdhury MAK, Mofijur M (2021) Estimation of sustainable bioenergy production from olive mill solid waste. Energies 14:7654
Veraa D, de Mena B, Jurado F, Schories G (2013) Study of a downdraft gasifier and gas engine fueled with olive oil industry wastes. Appl Therm Eng 51:119–129
Volpe M, Fiori L (2017) From olive waste to solid biofuel through hydrothermal carbonisation: the role of temperature and solid load on secondary char formation and hydrochar energy properties. J Anal Appl Pyrolysis 124:63–72
Volpe M, Wüst D, Merzari F, Lucian M, Andreottola G, Kruse A, Fiori L (2018) One stage olive mill waste streams valorisation via hydrothermal carbonisation. Waste Manag 80:224–234
Ximenes E, Kim Y, Mosier N, Dien B, Ladisch M (2011) Deactivation of cellulases by phenols. Enzyme Microb Technol 48:54–60
Yangui A, Abderrabba M (2018) Towards a high yield recovery of polyphenols from olive mill wastewater on activated carbon coated with milk proteins: experimental design and antioxidant activity. Food Chem 262:102–109
Yangui T, Dhouib A, Rhouma A, Sayadi S (2009) Potential of hydroxytyrosol-rich composition from olive mill wastewater as a natural disinfectant and its effect on seeds vigour response. Food Chem 117:1–8
Yangui T, Sayadi S, Gargoubi A, Dhouib A (2010) Fungicidal effect of hydroxytyrosol-rich preparations from olive mill wastewater against verticillium dahliae. Crop Prot 29:1208–1213
Zahran H, El-Kalyoubi M, Khallaf M, Abdel-Razek A (2015) Improving oils stability during deep-fat frying using natural antioxidants extracted from olive leaves using different methods. Middle East J Appl Sci 5:26–38
Zheng Z, Liu J, Yuan X, Wang X, Zhu W, Yang F, Cui Z (2015) Effect of dairy manure to switchgrass co-digestion ratio on methane production and the bacterial community in batch anaerobic digestion. Appl Energy 151:249–257
Acknowledgements
Enaime G. acknowledges the Alexander von Humboldt Foundation for financial support via the Georg Forster Research Fellowship for postdoctoral researchers. Authors also acknowledge support by the Open Access Publication Funds of the Ruhr-Universität Bochum. Open access funding enabled and organized by Project DEAL.
Funding
Open Access funding enabled and organized by Projekt DEAL.
Author information
Authors and Affiliations
Contributions
Conceptualization, G.E. and M.L.; methodology, G.E. and M.L.; investigation, writing—original draft preparation, G.E.; tables conceptualization, G.E. and S.D.; review and editing, G.E., S.D., M.W. and M.L.; visualization, G.E.; supervision, M.L and M.W. All authors have read and agreed to the published version of the manuscript.
Corresponding author
Ethics declarations
Ethics approval
Not applicable.
Consent for participate
Not applicable.
Consent for publication
Not applicable.
Conflict of interest
The authors declare no competing interests.
Additional information
Responsible Editor: Guilherme Luiz Dotto
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Enaime, G., Dababat, S., Wichern, M. et al. Olive mill wastes: from wastes to resources. Environ Sci Pollut Res 31, 20853–20880 (2024). https://doi.org/10.1007/s11356-024-32468-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11356-024-32468-x