The fiber-metal composites made of aluminum sheets and glass fibers reinforced with a polyester resin as the matrix were studied. The composites were prepared by hand lay-up method. Some aspects of manufacturing affecting the composite behavior were considered. In particular, the influences of the arrangement of layers and their number on the mechanical and physical properties of composites with ten different compositions were investigated. In addition two different densities of glass fibers were considered. The tensile modulus, tensile and impact strengths were determined following ASTM D3039 and ASTM D6110 standards. The results obtained show that the arrangement of the laminate layers influences Young’s modulus and the tensile strength of the composite. The impact test results of the laminated structure reinforced with glass fibers illustrate a significant increase in the impact strength owing to adding the glass fibers compared to the control specimens. The simulations of tests using ABAQUS-based FEA were performed.
Similar content being viewed by others
References
M. E. Golmakani, T. Wiczenbach, M. Malikan, S. M. Mahoori, and V. A. Eremeyev, “Experimental and numerical investigation of tensile and flexural behavior of nanoclay wood-plastic composite”, Materials, 14, No. 11, 2773 (2021).
M. E. Golmakani, T. Wiczenbach, M. Malikan, R. Aliakbari, and V. A. Eremeyev, “Investigation of wood flour size, aspect ratios, and injection molding temperature on mechanical properties of wood flour/polyethylene composites,” Materials, 14, No. 12, 3406 (2021).
D. Nowak, M. Clapa, P. Kula, M. Sochacki, B. Stonio, M. Galazka, M. Pelka, D. Kuten, and P. Niedzielski, “Influence of the Interactions at the Graphene–Substrate Boundary on Graphene Sensitivity to UV Irradiation,” Materials, 12, No. 23, 3949 (2019).
L. Li, L. Lang, S. Khan, and Y. Wang, “Investigation into Effect of the graphene oxide addition on the mechanical properties of the fiber metal laminates,” Polym. Test., 91, 106766 (2020).
M. E. Kazemi, L. Shanmugam, S. Chen, L. Yang, and J. Yang, “Novel thermoplastic fiber metal laminates manufactured with an innovative acrylic resin at room temperature,” Compos. Part A, 138, 106043 (2020).
M. Rathnasabapathy, A. P. Mouritz, and A. C. Orifici, “Finite element modelling of the impact response of fibre metal laminates under tension preloading,” Compos. Part A, 157, 106930 (2022).
M. Rathnasabapathy, A. C. Orifici, and A. P. Mouritz, “Impact damage to fibre metal laminates under compression loading,” Compos. Commun. 32, 101148 (2022).
X. Li, X. Ma, Sh. Li, Y. Guo, V. P. W. Shim, and X. Hao, “Deformation and failure of a novel fiber-metal hybrid lamina composite under quasi-static and impact loading,” Compos. Sci. Technol., 216, 109067 (2021).
L. Yao, Ch. Wang, W. He, Sh. Lu, and D. Xie, “Influence of impactor shape on low-velocity impact behavior of fiber metal laminates combined numerical and experimental approaches,” Thin Wall Struct., 145, 106399 (2019).
M. Megahed, M. A. Abd El-Baky, A. M. Alsaeedy, and A. E. Alshorbagy, “Improvement of impact and water barrier properties of GLARE by incorporation of different types of nanoparticles,” Fibers Polym., 21, 840–848 (2020).
M. A. Abd El-Baky and M. A. Attia, “Experimental study on the improvement of mechanical properties of GLARE using nanofillers,” Polym. Compos., 41, 4130–4143 (2020).
J. Bieniaś, P. Jakubczak, B. Surowska, and K. Dragan, “Low-energy impact behaviour and damage characterization of carbon fibre reinforced polymer and aluminium hybrid laminates,” Arch. Civ. Mech. Eng., 15, No. 4, 925–932 (2015).
M. Sadighi, R. C. Alderliesten, and R. Benedictus, “Impact resistance of fiber-metal laminates: A review,” Int. J. Impact Eng., 49, 77–90 (2012).
S. H. Song, Y. S. Byun, T. W. Ku, W. J. Song, J. Kim, and B. S. Kang, “Experimental and numerical investigation on impact performance of carbon reinforced aluminum laminates,” J. Mater. Sci. Technol., 26, No. 4, 327–332, (2010).
V. G. Reyes and W. J. Cantwell, “The Mechanical properties of fibre-metal laminates based on glass fibre reinforced polypropylene,” Compos. Sci. Technol., 60, No. 7, 1085–1094 (2000).
H. G. Kotik and J. E. Perez Ipiña, “Short-beam shear fatigue behavior of fiber metal laminate (Glare),” Int. J. Fatigue., 95, 236–242 (2017).
M. Shamohammadi Maryan, H. Ebrahimnezhad-Khaljiri, and R. Eslami-Farsani, “The experimental assessment of the various surface modifications on the tensile and fatigue behaviors of laminated aluminum/aramid fibers-epoxy composites,” I. J. Fatigue, 154, 106560 (2022).
A. Vasudevan, B. Navin Kumar, M. Victor Depoures, T. Maridurai, and V. Mohanavel, “Tensile and flexural behaviour of glass fibre reinforced plastic – Aluminium hybrid laminate manufactured by vacuum resin transfer moulding technique (VARTM),” Mater. Today-Proc., 37, 2132-2140 (2021).
Ch. Hu, L. Sang, K. Jiang, J. Xing, and W. Hou, “Experimental and numerical characterization of flexural properties and failure behavior of CFRP/Al laminates,” Compos. Struct., 281, 115036 (2022).
M. Zakeri, H. Mansoori, M. Sadeghian, and M. Guagliano, “Impact response of fiber metal laminates based on aluminum and UHMWPE composite: Numerical simulation,” Thin Wall Struct., 172, 108796 (2022).
W. Zhu, H. Xiao, J. Wang, and Ch. Fu, “Characterization and properties of AA6061-based fiber metal laminates with different aluminum-surface pretreatments,” Compos. Struct., 227, 111321 (2019).
Th. P. Vo, Z. W. Guan, W. J. Cantwell, and G. K. Schleyer, “Modelling of the low-impulse blast behaviour of fibre–metal laminates based on different aluminium alloys,” Compos. Part B, 44, No. 1, 141-151 (2013).
S. H. Khan, A. P. Sharma, R. Kitey, and V. Parameswaran, “Effect of metal layer placement on the damage and energy absorption mechanisms in aluminium/glass fibre laminates,” Int. J. Impact Eng., 119, 14-25 (2018).
A. P. Sharma and S. H. Khan, “Influence of metal layer distribution on the projectiles impact response of glass fiber reinforced aluminum laminates,” Polym. Test., 70, 320-347 (2018).
G. R. Rajkumar, M. Krishna, H. N. Narasimhamurthy, Y. C. Keshavamurthy, and J. R. Nataraj, “Investigation of tensile and bending behavior of aluminum based hybrid fiber metal laminates,” Proc. Mat. Sci., 5, 60-68 (2014).
Gunnink, J.W. “Composite laminate of metal sheets and continuous filaments-reinforced synthetic layers”: (Akzo NV, Arnhem, The Netherlands) US Pat 4 935 291 (19 June 1990), Compos., 23, 205 (1992).
Author information
Authors and Affiliations
Corresponding author
Additional information
Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 58, No. 6, pp. 1193-1206, November-December, 2022. Russian DOI: https://doi.org/10.22364/mkm.58.6.06.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Golmakani, M.E., Wiczenbach, T., Malikan, M. et al. Experimental and Numerical Study on Mechanical Characteristics of Aluminum/Glass Fiber Composite Laminates. Mech Compos Mater 58, 835–844 (2023). https://doi.org/10.1007/s11029-023-10072-3
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11029-023-10072-3