Polyimide (PI) films based on poly(pyromellitic dianhydride-co-4,4′-oxydianiline) (PI-PM) were filled with different nanoparticles, such as organically modified montmorillonite (MMT), vapor-grown carbon nanofibers (VGCF), and silicate nanotubes (SNT) of different concentration.. Rheological measurements and structural investigations showed a relatively good dispersion of the nanoparticles in the PI matrix to an extent that depended on the type and morphology of the nanoparticles used. The mechanical (tensile modulus, strength, and deformation at break) and the barrier (oxygen permeability) properties of PI-PM nanocomposite films were investigated. The polyimide nanocomposites filled with SNT and tubular VGCF nanoparticles showed an increased tensile modulus with increasing volume concentration of the nanoparticles without a catastrophic decrease in the elongation at break. In addition, the MMT particles, chemically modified with 4,4'-bis-(4′′-aminophenoxy)diphenylsulfone, significantly improved the barrier properties of the PI-PM films, which exceeded those of the nanocomposites filled with VGCF or SNT. The relative poor oxygen barrier and mechanical properties of the PI-PM/VGCF nanocomposite films are ascribed to the relative weak adhesion between the VGCF and the polyimide matrix, which was confirmed by scanning electron microscopy of the fracture surface of these films.
Similar content being viewed by others
References
H. Fischer, “Polymer nanocomposites: From fundamental research to specific applications,” Mater. Sci. Eng., 23, 763–772 (2003).
F. Hussain, M. Hojjati, M. Okamoto, and R. E. Gorga, “Polymer-matrix nanocomposites, processing, manufacturing, and application: An overview,” J. Compos. Mater., 40, 1511–1575 (2006).
S. Ray and M. Okamoto, “Polymer/layered silicate nanocomposites: A review from preparation to processing,” Progr. Polym. Sci., 28, 1539–1641 (2003).
Q. Zeng, A. Yu, G. Lu, and D. Paul, “Clay-based polymer nanocomposites: Research and commercial development,” J. Nanosci. Nanotechn., 5, 1574–1592 (2005).
V. E. Yudin, J. U. Otaigbe, V. M. Svetlichnyi, E. N. Korytkova, O. V. Almjasheva, and V. V. Gusarov, “Effects of nanofiller morphology and aspect ratio on the rheo-mechanical properties of polyimide nanocomposites,” eXPRESS Polym. Lett., 2, 485–493 (2008).
V. E. Yudin, J. U. Otaigbe, S. V. Gladchenko, B. G. Olson, S. I. Nazarenko, E. N. Korytkova, and V. V. Gusarov, “New polyimide nanocomposites based on silicate type nanotubes: Dispersion, processing and properties,” Polymer, 48, 1306–1315 (2007).
V. E. Yudin, J. U. Otaigbe, L. T. Drzal, and V. M. Svetlichnyi, “Novel semicrystalline thermoplastic R-BAPB type polyimide matrix reinforced by graphite nanoplatelets and carbon nanoparticles,” Adv. Compos. Lett., 15, 137–143 (2006).
K. Takashi, V. E. Yudin, J. U. Otaigbe, and V. M. Svetlichnyi, “Compatibilized polyimide (R-BAPS)/BAPS-modified clay nanocomposites with improved dispersion and properties,” Polymer, 48, 7130–7138 (2007).
M. I. Bessonov, M. M. Koton, V. V. Kudryavtsev, and L. A. Laius, Polyimides — Thermally Stable Polymers, Plenum Publ. Corp., New York (1987).
E. N. Korytkova, A. V. Maslov, L. N. Pivovarova, I. A. Drozdova, and V. V. Gusarov, “Formation of Mg3Si2O5(OH)4 nanotubes under hydrothermal conditions,” Glass Phys. Chem., 30, 51–55 (2004).
E. N. Korytkova, A. V. Maslov, L. N. Pivovarova, Y. V. Polegotchenkova, V. F. Povinich, and V. V. Gusarov, “Formation of Mg3Si2O5(OH)4-Ni3Si2O5(OH)4 nanotubes under high temperature and pressure,” Inorgan. Mater., 41, 1–7 (2005).
V. E. Yudin, G. Divoux, J. U. Otaigbe, and V. M. Svetlichnyi, “Synthesis and rheological properties of oligoimide/ montmorillonite nanocomposites,” Polymer, 46, 10866–10872 (2005).
E. Garboczi, K. Snyder, J. Douglas, and M. Thorpe, “Geometrical percolation threshold of overlapping ellipsoids,” Phys. Rev. E, 52, 819–828 (1995).
T. Ogasawara, Y. Ishida, and T. Ishikava, “Properties of vapor-grown carbon nanofiber/phenylethynyl terminated polyimide composite,” Adv. Compos. Mater., 13, 215–226 (2004).
D. Qian, E. C. Dickey, R. Andrews, and T. Rantell, “Load transfer and deformation mechanisms in carbon nanotubepolystyrene composites,” Appl. Phys. Lett., 76, 2868–2870 (2000).
P. K. Mallick, Fiber-Reinforced Composites, Marcel Dekker, New York (1993).
S. Piperno, I. Kaplan-Ashiri, S. R. Cohen, R. Popovitz-Biro, H. D. Wagner, R. Tenne, E. Foresti, I. G. Lesci, and N. Roveri, “Characterization of geoinspired and synthetic chrysotile nanotubes by atomic force microscopy and transmission electron microscopy,” Adv. Funct. Mater., 17, 3332–3338 (2007).
R. L. Jacobsen, T. M. Tritt, J. R. Guth, A. C. Ehrlich, and D. J. Gillespie, “Mechanical properties of vapor-grown carbon fibers,” Carbon, 33, 1217–1221 (1995).
B. G. Olson, J. J. Decker, S. I. Nazarenko, V. E. Yudin, J. U. Otaigbe, E. N. Korytkova, and V. V. Gusarov, “Aggregation of synthetic chrysotile nanotubes in the bulk and in solution probed by nitrogen adsorption and viscosity measurements,” J. Phys. Chem.: Part C, 112, 12943–12950 (2008).
X. Chen, K. Yoon, C. Burger, I. Sics, D. Fang, B. S. Hsiao, and B. Chu, “In-situ x-ray scattering studies of a unique toughening mechanism in surface-modified carbon nanofiber/UHMWPE nanocomposite films,” Macromolecules, 38, 3883–3893 (2005).
S. A. Stern, Y. Mi, H. Yamamoto, and A. K. St. Clair, “Structure/permeability relationships of polyimide membranes: Applications to the separation of gas mixtures,” J. Polym. Sci., Part B, 27, 1887–1909 (1989).
L. E. Nielsen, “Models for the permeability of filled polymer systems,” J. Macromol. Sci., Part A, 1, 929–942 (1967).
G. H. Fredrickson and E. S. G. Shaqfeh, “Heat and mass transport in composites of aligned slender fibers,” Phys. Fluids A: Fluid Dynamics, 1, 3–20 (1989).
Author information
Authors and Affiliations
Corresponding author
Additional information
Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 47, No. 3, pp. 485–496 , May-June, 2011.
Rights and permissions
About this article
Cite this article
Yudin, V.E., Otaigbe, J.U., Nazarenko, S.I. et al. A comparative study on the mechanical and barrier characteristics of polyimide nanocomposite films filled with nanoparticles of planar and tubular morphology. Mech Compos Mater 47, 335–342 (2011). https://doi.org/10.1007/s11029-011-9212-z
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11029-011-9212-z