Abstract
Predictive monitoring of two key properties of nanocellulose, aspect ratio and yield of nanofibrillation, would help manufacturers control and optimize production processes, given the uncertainty that still surrounds their influential factors. For that, 20 different types of cellulosic and lignocellulosic micro/nanofibers produced from spruce and pine softwoods, and by different pre-treatment and fibrillation techniques, were used as training and testing datasets aiming at the development and evaluation of three machine learning models. The models used were Random Forests (RF), Linear Regression (LR) and Artificial Neural Networks (ANN), broadening the scope of our previous work (Santos et al. in Cellulose 29:5609–5622, 2022. https://doi.org/10.1007/s10570-022-04631-5). Performance of these models were evaluated by comparing statistical parameters such as Mean Absolute Percentage Error (MAPE) and R². For the aspect ratio and the yield of nanofibrillation, inputs were chosen among these easily controlled or measured variables: Total lignin (wt%), Cellulose (wt%), Hemicellulose (wt%), Extractives (wt%), HPH Energy Consumption (kWh/kg), Cationic Demand (µeq/g), Transmittance at 600 nm and Consistency index (Ostwald-De Waele’s k). In both cases, the ANN models trained here provided satisfactory estimates of aspect ratio (MAPE = 4.54% and R2 = 0.96) and the yield of nanofibrillation (MAPE = 6.74% and R2 = 0.98), being able to capture the effect of the applied energy along the fibrillation process. RF and LR models resulted in correlation coefficients of 0.93 and 0.95, respectively, for aspect ratio, while for yield of nanofibrillation the correlation coefficients were 0.87 and 0.92.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
Introduction
Nanocellulose consists of a group of cellulose-based materials that have at least one dimension in the nanometric scale and englobes three main types of nanostructures: cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs) and bacterial nanocellulose (BNC) (Abdul Khalil et al. 2014). Taking a closer look at cellulose micro/nanofibers (CMNFs), these are generally produced by a top-down approach, including a pre-treatment stage of lignocellulosic feedstock followed by a fibrillation step. Pre-treatment methods englobe chemical and enzymatic treatments, oxidation procedures and mechanical techniques. The fibrillation process, on the other hand, is mainly mechanical and it is based on delaminating the pulp, for example, by means of high-pressure homogenization, grinding and others (Klemm et al. 2018; Dai et al. 2019). CMNFs are characterized by the presence of both amorphous and crystalline regions within the cellulose fiber, being both strong and flexible. Because of that, they are able to form an entangled network and, therefore, CMNF applications include emulsification in the food industry, rheology modifiers, reinforcing agent in the packaging and automotive sectors, water treatment and membrane production (Alila et al. 2013; Klemm et al. 2018). If lignin is kept along the whole process (Serra-Parareda et al. 2021a), be it with the aim of valorizing lignocellulosics with high yields, to avoid the use of hazardous chemicals, or to attain less hydrophilic nanocellulose forms, it is convenient to talk about lignocellulosic micro/nanofibers (LCMNFs).
Usually, criteria to discriminate microfibers from nanofibers imply that the diameter of the former is greater than 100 nm (Isogai 2020). This work opts for a pragmatic definition that may or may not coincide with the 100-nm criterion. In dilute suspensions of LCMNFs, the proportion of fibers that are small enough so that Brownian motion prevails over gravitational settling is called “yield of nanofibrillation” (Besbes et al. 2011; Sanchez-Salvador et al. 2021b). Particles that tend to sediment, despite having undergone a destructuring process, constitute the microfibrillated fraction.
In spite of the broad spectrum of applications, large scale production of nanocellulose is challenging and one of the reasons is the lack of easy, rapid and accurate measuring techniques for process monitoring (Serra-Parareda et al. 2021c). Moreover, some methods used for property measurement are time-consuming or tedious, even at laboratory scale. The aspect ratio, an important morphological property of CMNFs that strongly influences various properties regarding final applications, such as mechanical and rheological parameters (Leong et al. 2022), is measured either by gel point methodology or by very high-resolution microscopy. Another relevant parameter, the yield of nanofibrillation, can be obtained by separation of the dispersed and settling fractions using stages of centrifugation, drying and weighing (Raj et al. 2016; Tarrés et al. 2020b; Sanchez-Salvador et al. 2021a). As noticeable, these techniques involve steps that are quite tiresome for monitoring purposes in the industry. Another relevant aspect is the lack of consistent mathematical models able to describe and capture the complex relations between the features of the CMNFs produced and the characteristics of the raw material and process conditions.
Among the most valuable efforts to benchmark CNF suspensions, the quality index proposed by researchers from LGP2 (Desmaisons et al. 2017) and the correlations of the Arrhenius Lab in Stockholm (Kriechbaum et al. 2018) should be cited. The former relied on optical microscopy, nanosized fraction and turbidity tests, while the latter was mainly based on the porosity and the apparent density of anisotropic CNF foams. Nonetheless, despite the usefulness of post hoc quality assessment, accurate monitoring involving variables to be measured on-line, or determined and controlled beforehand, would be an important leap forward in the manufacturing of nanoscale cellulose products. For instance, the strength of nanocellulose-based materials has been predicted, to different levels of satisfaction, by micromechanical models, such as the Cox-Krenchel method (Lee et al. 2014; Mugwagwa and Chimphango 2022) or combinations between the Kelly-Tyson and Pukandszky models (Tarrés et al. 2020a). In this context, machine learning (ML) algorithms constitute an advantageous tool to apply in predicting and controlling the properties of CNF suspensions, films and materials derived thereof, which is a field that has been scarcely explored (Özkan et al. 2019; Torrents-Barrena and Pellicer 2021).
Machine learning is a subfield of artificial intelligence that can be used to predict outputs based on previously presented data without the need of explicit programming, which means, in a way that the computer can learn “by itself” from data and be more accurate with time. ML can be a great tool for getting insights and solving complex problems that require fine-tuning or when existing solutions are not satisfactory (Géron 2019). Some algorithms frequently applied in Machine Learning are Linear Regression (LR), Decision Trees, Random Forests (RF), Artificial Neural Networks (ANN), and Clustering. Putting a spotlight on the algorithms typically used in Material Science, supervised learning algorithms usually prevail, such as LR, RF and ANN.
When it comes to ML techniques in the cellulose/nanocellulose fields, some work worthy of mention are: Aguado et al. (2016), using a support regression vector approach to predict paper strength from morphological characteristics; Pennells et al. (2022), with a similar approach on nanopaper; Özkan et al. (2019), who evaluated three different algorithms (LR, RF and ANN) in the prediction of mechanical properties of three-component nanocomposite films; Almonti et al. (2019), who made use of ANNs to predict fiber length based on the pulp refining process parameters. Recently, another article of ours provided ANN predictions of the aspect ratio of (L)CMNFs, using pulps from aspen, eucalyptus and spruce to validate the performance of the model with other types of biomass (Santos et al. 2022). This work widens the scope of said attempts, including the yield towards nanostructured cellulose and other alternative methods. The ability to rapidly predict the yield and the morphological properties of nanocellulose based on the joint use of machine learning tools and a set of easily measurable input parameters of the starting pulps is critical for industrial applications. An example of application follows: an on-line series of optical and rheological sensors detect a set of variables that would result in a low yield of nanofibrillation, and thus the cellulose stream is recycled to the fibrillation unit for one more pass. For these reasons, this study focusses on developing techniques that are inexpensive, easy to implement and widely applicable, such as machine learning models combined with selected input variables. All considered, the present work seeks to take one more step towards the effective control and predictive monitoring of the fibrillation of (ligno)cellulosic pulps. Besides ANN, two ML algorithms, LR and RF, were applied for predicting both the yield of nanofibrillation and the aspect ratio of laboratory-produced (L)CMNFs. It should be noted that, as the previous literature understandably focuses on predicting the mechanical properties of the nanocellulose-based end product, the yield of nanofibrillation (a key indicator of the extent of the fiber disruption itself) has been overlooked. Inputs are based on easily obtainable data from the pre-treated fibers and the fibrillation process. After discussing the influence of the most relevant variables, the three models are compared by means of their performance parameters and they are analyzed regarding the feasibility of their application.
Experimental
Dataset materials
The data used for training and testing the models were obtained from previous work of our group (Serra-Parareda et al. 2021c). Therein, four cellulosic and lignocellulosic pulps, following different treatments, were employed to produce mechanical (L)CMNFs with varying nanofibrillation yields. For the sake of comparison, it should be noted that this experimental dataset, explicitly displayed in Table 1, partially overlaps that of our previous work on the ANN-based prediction of the aspect ratio (Santos et al. 2022).
Three of the pulps were obtained from pine (Pinus radiata), considering that they had undergone thermomechanical, unbleached kraft and bleached kraft treatments (TMP, UKSP and BKSP respectively), whilst the final one was obtained from spruce (Picea abies) that had undergone thermomechanical pulping and peroxide bleaching (BTMP). The pre-treatment step of these pulps consisted in a mechanical refining stage in a Valley beater, designed in compliance to TAPPI T200 (TAPPI 2020), and all four pulps were refined for 60 min. Afterwards, each pulp was passed through a high-pressure homogenizer (HPH), NS1001L PANDA 2 K-GEA (GEA Niro Soavy, Parma, Italy), gradually increasing the number of passes from 3 to 9 and pressure from 300 to 900 bar. This resulted in five HPH levels of energy consumption, which was measured by means of a device from Circutor (Barcelona, Spain), model CVM-C10. Samples were taken from each of the stages, resulting in 5 types of CNFs for each pre-treated pulp and thus totalizing 20 (L)CMNF different samples (Table 1).
The pre-treated pulps were characterized in terms of their chemical composition and crystallinity index (%). Data regarding these parameters, whose extraction and curation is explicit in the aforementioned article (Serra-Parareda et al. 2021c), can be checked in Table 2. Briefly, ash and extractives were determined gravimetrically after combustion at 525 °C and ethanol/benzene extraction, respectively, according to the common TAPPI methods (TAPPI 2020). Structural carbohydrates and total lignin were determined by following the analytical procedure NREL/TP-510-42618 (Sluiter et al. 2012), which involves hydrolysis, spectrophotometry, and liquid chromatography. Crystallinity was estimated from the (200) peak of cellulose I in X-ray diffraction patterns (Supplementary Information, Figure S1), applying Segal’s empirical method (Segal et al. 1959).
The CNFs produced were characterized by measurement of rheology properties, such as consistency index (k) and flow index (n), yield of nanofibrillation, aspect ratio, transmittance at 600 nm and cationic demand. In particular, the yield of nanofibrillation was understood as the fraction of solid material that did not sediment when centrifuging a 0.2% CNF suspension at 3400 g for 20 min. Regarding the aspect ratio, it was estimated via the gel point (Varanasi et al. 2013), which was in turn calculated from the sediment height at several concentrations, as described in detail elsewhere (Sanchez-Salvador et al. 2021c). The cationic demand was determined by potentiometric back titration (Serra-Parareda et al. 2021b).
Machine learning techniques
The ML algorithms were implemented in Python and the environment used for training and testing the models was the open-source platform Jupyter Notebook. The whole dataset consisting in the 20 samples was separated into a training and testing subsets considering 80% and 20% of experimental data, respectively.
The modeling approach here used a multiple input–single output (MISO) structure for each kind of model, considering aspect ratio and yield of nanofibrillation (%) as the output parameter for each model. The initial features chosen to be the inputs were: cellulose (wt%), total lignin (wt%), hemicellulose (wt%), ash (wt%), extractives (wt%), crystallinity index (%), transmittance at 600 nm (T600), cationic demand (CD), consistency index (k), flow index (n) and energy consumption in the high-pressure homogenizer (kWh/kg).
The features to be used in the final models responded to a double criterion. On the one hand, they were selected to be suitably applied at industry. On the other, based on their simplicity and reproducibility. In this sense, some of the parameters were related to pre-treated pulps (cellulose, hemicellulose, lignin, extractives and ash content, and crystallinity), some others to (L)CMNF characteristics (cationic demand, transmittance, consistency index and flow behavior index), and to process (energy consumption during HPH). Although the determination of the chemical composition of the pre-treated pulps requires specific gravimetric methods and chromatographic analyses, the homogeneity of the material allows their determination less frequently and, indeed, it can be a parameter provided by the pulp supplier. Energy consumption can be directly measured from the fibrillation equipment with the appropriate device and, finally, the selected (L)CMNF characteristics can be directly measured with low sample processing.
Table 3 summarizes the variables and range values investigated for ML modelling. For LR and ANN, input data was normalized since these algorithms are affected by the order of magnitude of the features, as it will be explained in the following sections.
Linear regression
LR models are based on a single or multiple linear function, relating a dependent output with one or a sum of multiple independent inputs, each of them being multiplied by their specific weight, plus a constant (Géron 2019):
In Eq. 1, the first term \(\widehat{y}\) refers to the predicted value, while \(\theta _{0}\) represents the constant and \(\theta _{n}\) the weight associated to each input value \({x}_{n}\).
As aforementioned, applying LR in machine learning requires either normalization or standardization of data. As it can be seen from Eq. 1, if an input is numerically large, even though its weight is not so big, it might still have a strong impact in the prediction. Therefore, in order to eliminate this kind of influence, all input values should be in the same range. Further details of the multiple linear regression algorithm can be found elsewhere (Maulud and Abdulazeez 2020).
Random forest
RF is an algorithm based on a conjunction of multiple Decision Tree models and it is usually trained by the bagging method. It fits a number of Decision Trees, and the final outcome is the average from the results obtained by each individual tree. RF adds extra randomness while growing the trees and it looks for the best feature among a random subset of them while splitting a node. In this way, RF generally performs better than single Decision Trees and because of the large number of predicators, it does not overfit, giving a more robust performance. Its structure is outlined in Fig. 1. Internal estimators such as generalization error, strength and correlation are used both for monitoring the performance of the model in the face of the increased number of features used in the splitting, and for determining their importance (Breiman 2001). Because of the principal function of RF models, data normalization is not required.
Artificial neural networks
ANNs are systems that resemble biological neurons, being based on small processing units that are intertwined. Each neuron receives input values that have an associated weight, and the network makes use of activation functions, including, e.g., rectified linear unit and sigmoidal functions, to connect between layers of neurons (Haykin 1999; Géron 2019).
Its structure comprises the input layer, the hidden layer and the output layer of neurons. The input layer possesses the same depth as the number of features used in the model. The hidden layer includes as many layers of neurons intended and the depth of each hidden layer is a hyperparameter that can be tuned. Finally, the output layer size is the same as the number of outputs described by the model. ANN makes use of backpropagation and optimization algorithms in order to improve the weights and bias associated. A simplified scheme is depicted in Fig. 2 and more detailed descriptions can be found elsewhere (Haykin 1999; Torrents-Barrena and Pellicer 2021; Santos et al. 2022).
Model evaluation
ANNs, RF and multiple LR models had their accuracy tested and compared by statistical parameters of customary use: Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE), Root Mean Squared Error (RMSE) and R² score.
MAE and MAPE can be calculated using Eqs. 2 and 3, where n represents the number of datapoints, is the actual value for the ith sample and is the prediction of the ith sample.
RMSE is calculated as represented in Eq. 4. The notations are the same for the metrics stated above.
The determination coefficient R² can be calculated by Eqs. 5 and 6, where the notations are the same as stated above, with exception of \(\stackrel{-}{y}\), which represents the mean value of all actual observations.
Results and discussion
Aspect ratio
On the input parameters
Due to the number of combinations tested, Table 4 only presents the results for the three best combinations of features in each case. Statistical parameters are shown for the sake of comparison between different groups of parameters and their influence on the performance in the train and test subsets.
As it can be seen from Table 4, modelling with all features was performed for the three algorithms, followed by up to 5-feature models in which mainly chemical components are present in the modelling. This funneling of parameters was done based on the models with subset of features that performed better and on the two guidelines presented in the Experimental section. Additionally, we also considered the features that were amongst the most important and/or that had higher absolute values of Pearson correlation coefficient to help funneling the options. These features can be seen in Fig. 3; Table 5.
It is possible to observe that cellulose, hemicellulose, total lignin content and crystallinity index appear in both Fig. 3; Table 5 as important features. Since crystallinity index and flow index (n) were not considered as practical parameters, they were not considered to be retained in the final model, even though they were simulated. On the other hand, chemical composition was preserved for initial testing, and later in conjunction to other features, even the ones that did not present at first as the most relevant. HPH energy requirement is an example of parameter that was selected to be maintained in the modelling since it is a process parameter of easy acquirement and provided good performance.
Regarding the performance of the models presented in Table 4, for the random forest models one can observe that when all features were used, the best results were attained. However, they account for 11 inputs, among which there are both easier and harder to measure properties. When model 2 is run, which consisted in five inputs, comparable results are achieved. Other combinations were tried, one of them being model 3, the final subset of features chosen for this algorithm. In this case, we get slightly worse MAE and MAPE, but very similar RSME and R² compared to model 1, but exact performance of model 2, indicating that extracts (wt%) and hemicellulose (wt%) were not necessary for good performance. In this case, we had only three features selected which made use of very easy to measure parameters. For the linear regression models, when all features were used as inputs, again very good results are obtained, but this would not be a practical case. When the number of features is diminished to the subset used for model 2, the model still performs well. When the number of features is decreased to the final subset chosen, the exact results are gathered. Finally, for the ANN, model 1 presents very satisfactory results, as already expected for an all-feature simulation. Model 2, which used the same features as model 2 of LR, performed the best among all simulations for neural networks and was chosen as the final one. Model 3 performed worse and was discarded. Other combinations apart from these three presented here were tested, but they were not considered suitable for the application as well, either for low performance, either for requiring not the most interesting inputs.
Therefore, all final models selected were created using easily obtainable parameters as input features. Summarizing them, for LR, they were: cellulose (wt%) (x1), hemicellulose (wt%) (x2), total lignin (wt%) (x3) and energy requirement in the HPH (kWh/kg) (x4). RF employed three input features, the same as LR except hemicellulose (wt%). ANN required the highest number of factors, encompassing total lignin (wt%), cellulose (wt%), hemicellulose (wt%), extractives (wt%) and HPH energy consumption (kWh/kg). The first four belong to the chemical composition of the pulps, but, instead of requiring chromatography or advanced detectors, they can be estimated via the typical TAPPI methods (TAPPI 2020), consisting basically on gravimetrical determinations and the use of oven drying, filtration, and cheap reagents. It is worth noting that, although these gravimetrical methods were followed in the source work (Serra-Parareda et al. 2021c), they could be, to a certain point, further simplified towards in-line optical measurements in industrial applications. For instance, the conjugated structures of lignin absorb ultraviolet radiation (~ 280 nm), and they also have unique absorption bands in infrared spectra (Nader et al. 2022).
Additionally, it is possible to observe that the final models chosen for each algorithm encompass a distinct number of features or combination of them. These differences between the number and types of variables among the algorithms occur due to their different principal of function. The parameters required for good modelling will not necessarily be the same among the models, and this discrepancy remains a valid point to use for evaluation and comparison between algorithms. Considering the current knowledge on the effects of chemical composition on nanocellulose properties, the selection of input variables in this regard, such as the weight percentages of lignin and cellulose (common to all models), can be deemed consistent. For instance, lignin has been alleged to be detrimental for aspect ratio (Li et al. 2016), as a lignin-rich cell wall grants lower deformability in the ulterior conversion to nanocellulose. Likewise, a significant influence of the extent of fibrillation, expressed in this case as energy consumption, was expected. Such energy demand is directly proportional to the differential pressure exerted, according to Bernoulli’s principle (Serra-Parareda et al. 2022), and thus it is inferred that the more energy supplied, the more nanostructured (ligno)cellulosic fibers become. The reason lies in the native structure of the fiber itself, which, in a top-down sequence, is made out of fibrils with increasing aspect ratio, ending with the extremely slim elementary fibrils that constitute each microfibril. The lower the number of elementary fibrils that (L)CMNFs encompass, the higher the aspect ratio.
Performance of the predictive models
The LR model for the aspect ratio can be seen in Eq. 7. The RF model consisted in a 17-estimator forest. ANN’s architecture comprised the aforementioned 5 inputs in the first layer, 10 neurons in the only hidden layer of the system and 1 output—aspect ratio. The activation function used in the hidden layer was the sigmoid function and the linear function was used for generating the final prediction.
Figures 4, 5 and 6 show the target values versus the predicted values for aspect ratio from LR, RF and ANN models, respectively. Bar plots in said figures refer to real values. Cross markers refer to prediction values. Levels 1 to 5 indicate the increase in the applied energy, accordingly to the five levels of HPH intensity presented in Table 1.
From these plots, it is verified that all algorithms failed to predict accurately the point BKSP_level_1 and that all BKSP points are not as precisely met as the other groups of samples were. This may be because they presented very high aspect ratios, and therefore this data point was regarded as an outlier. Nonetheless, ANN model was able to capture the trend that BKSP samples took better than the other models, regarding the energy intensity increase, as noticeable in Fig. 6. Analyzing each model, as expected, LR provided linear relations for each group of samples, which is not quite the best for describing them, with exception of UKSP group. In spite of that, interestingly, it resulted in a better R² (0.9508), RMSE (12.221) and MAE (8.766) than RF model. This one was able to catch the non-linearity in the increase of the aspect ratio in each group, but did not quite meet some experimental values. In this way, its MAPE of 8.18% was lower than LR’s (9.07%), but the other metrics were worse: MAE of 9.760, RMSE of 14.448 and R² of 0.9313. The best model that was able to grasp the trends and had better quality of performance was the ANN model. ANN seized to represent almost perfectly the increasing trends and differences from each group of samples, at the same time it predicted very precise values (with exception of BKSP, as stated above). Metrics for ANN model were: MAE of 6.317, MAPE of 4.54%, RMSE of 11.356 and R² of 0.9575. All performance indicators are gathered in Table 6.
Despite the limitations specified above, all models presented an R² above 0.9 and mean percent errors lower than 10%. Also, they were able to capture the increase of aspect ratio as the energy intensity applied in the HPH grew, as well as being able to differentiate each group of samples. Perhaps ANN performed better than other models and was able to catch the nuances of the trends because of the activation function, which was sigmoidal, but at the expense of using more input variables. From Figs. 4, 5 and 6, one can observe that the increase in the aspect ratio is not linear and the behavior of the trend is different for each kind of treated pulp. For instance, BTMP does not show an increase in AR when there is an increase in the energy applied, apart from the BTMP_level_1 to BTMP_level_2 samples. This particularity is very different from what the other groups of samples show. TMP and UKSP resemble a linear increase, however, BKSP shows a large jump from BKSP_level_1 to BKSP_level_3 and forth on. ANN is a more complex algorithm, where different hyperparameters can be tuned in order to improve performance. As discussed above, it is able to grasp intricate relationships. Therefore, it is noticeable that, regarding the ability to simulate trends, LR did the poorest job, whilst the RF model performed in average and the ANN model performed very well, being evident that a more elaborate algorithm resulted in a better grasp of the complexity of the problem.
If the performance of these models satisfy nanocellulose manufacturers, they could be used for the predictive monitoring of key properties of the CNF suspension itself and of the end product. For instance, CNFs with high aspect ratio are entangled to a larger extent and, consequently, attain better barrier properties when used to coat packaging paper (Wang et al. 2021).
Yield of nanofibrillation
On the input parameters
Similarly to the aspect ratio, out of the large number of combinations tested, Table 7 presents the results for the top three combinations of features chosen to predict the nanofibrillation yield. Statistical parameters are displayed for the sake of comparison between distinct groups of parameters and their influence on the performances in the train and test subsets.
As it can be seen from Table 7, in this case, the modelling also started with all the features for the three algorithms. Afterwards, mainly final nanocellulose properties are present in the modelling. This is also due to the funneling of parameters that was done based on the models with a subset of features that performed better and on the two guidelines presented in the Experimental section. Furthermore, the features that were presented as most important for the RF models and that had higher absolute values of Pearson coefficient for the LR model were taken into consideration. These parameters can be seen in Fig. 7; Table 8.
It is possible to observe that transmittance, cationic demand, HPH energy consumption and consistency index (k) appear in both Fig. 7; Table 8. For this reason, they were chosen to be tested first and later in conjunction to other features, even the ones that did not present at first as the most relevant. For instance, extractives (wt%) did not appear as one of the most relevant factors in terms of the Pearson correlation coefficient. However, it contributed to the performance of the LR model more significantly than other parameters of the chemical composition, such as ash (wt%) or cellulose (wt%). It is important to highlight that, in the case of the Pearson correlation coefficient, the values presented regard the individual relevance of each feature with respect to the output of interest. Although the correlation coefficient value for extractives (wt%) was low, when taken into account in conjunction with the other features (transmittance, cationic demand, HPH energy consumption and consistency index) it helped to better fit the response. The improvement in the metrics, mainly in the train subset, can be observed in Table 7, where models 2 and 3 are compared.
From Table 7, one can observe that the best results were achieved also by a three-input model for the random forest, which had better performance when comparing to a model with all the initial features and with a 5-input one. In the case of LR, the all-feature model has a more drastic difference between train and test sets, which is not very good, once this may indicate overfitting. For model 2, the performances of both subsets are both more similar and better when comparing to models 1 and 3, thus it was selected as the chosen one. Finally, for the neural network, it was possible to obtain very good models with all the examples in the table, maintaining the topology scheme of the same number of neurons in the input and hidden layer. Thus, in this case, model 3 (4 input) was chosen as the best one. Other combinations apart from these three presented here were tested, but they were not considered suitable for the application as well, either for low performance, either for requiring not the most interesting inputs.
Therefore, in order to summarize the choices of final models for the yield of nanofibrillation, the final inputs selected were as follows. For LR model: transmittance at 600 nm (x1), cationic demand (µeq/g) (x2), consistency index k (x3), extractives (wt%) (x4), and HPH energy requirement (kWh/kg) (x5). For the ANN model, all inputs above were used, with exception of extractives, totalizing four inputs. RF required even less features, being only three: cationic demand, transmittance and HPH energy supply. Regardless of the number of features used in each model, all of them are low-cost inputs that can be easily measured. In particular, the three factors for the RF model can be roughly quantified in real time, in-line, and by rapid and non-destructive methods: potentiometry with ion-selective electrodes for the cationic demand (although the accurate determination would require a titration), photometry at a single wavelength to detect the loss of intensity of the incident light, and direct reading of electric power. Should the resulting combination of measurements be related to an unacceptably low yield, recycling for further fibrillation would be triggered, automating the common decision in a typical batch process. Extractives can be determined gravimetrically after a solid–liquid extraction with organic solvents, while the consistency index, directly proportional to the apparent viscosity, would require a rheometer (Xu et al. 2016; Serra-Parareda et al. 2021c).
It is noticeable that the majority of these inputs are related to either a process parameter (HPH energy requirement) or final nanocellulose characteristics (cationic demand, transmittance and consistency index). These are consistent with literature as well. A higher differential pressure, as aforementioned for the aspect ratio, causes more disruption, and therefore it generates more nanofibers. This same effect, the fact that the proportion of nano to microfibers increases, is also related to higher transparency, i.e., higher transmittance within the visible light spectrum, since smaller particles scatter light to a lesser degree (Movsesyan et al. 2022). The cationic demand is due to the remaining negatively-charged functional groups in (ligno)cellulosic pulps, be it carboxylates from the hydrolysis of lignin/hemicellulose ester bonds, glucuronic acid units in hemicelluloses, and even polarized hydroxyl groups. In pulps, most of them do not interact with the titrating polyelectrolytes during the determination of the cationic demand, as they are inside the fiber, but mechanical disruption makes them easily accessible, which is why surface charge is so robustly correlated to the specific surface area (Serra-Parareda et al. 2021b). Regarding the rheological behavior, it is well known that pulps and nanocellulose suspensions, in general, experience thinning with shear (n < 1), but, besides that, reducing the particle size has complex effects on the apparent viscosity. On the one hand, the frequency of particle–solvent and particle–particle interactions should increase with decreasing particle size (e.g., by nanofibrillation). On the other hand, the viscosity of nanocolloids is known to increase with increasing particle size (Wang et al. 2011). In any case, what we often observe when increasing nanofibrillation is that the consistency index and the flow behavior index do not follow the same trends (Aguado et al. 2022), and thus the apparent viscosity itself is not as adequately correlated to the yield of nanofibrillation as the consistency index from the Ostwald–De Waele equation.
Aspect ratio and yield share a common mechanical basis, as the progressive breakdown of a fiber into its constituting fibrils implies the generation of thinner particles. Not only do these thinner fibrils have higher aspect ratio, but they are also less prone to gravitational effects given their lower hydrodynamic radius. However, fibrils do not follow a Stokian settling behavior (Kim et al. 2021), and their interlocking and entanglement are ubiquitous when their concentration is high enough. Therefore, the behavior of dilute suspensions is not necessarily correlated to the gel-forming capabilities of highly entangled systems (Sanchez-Salvador et al. 2020). In other words, the aspect ratio and the yield of nanofibrillation are independent responses that, nonetheless, may be affected by some factors in a qualitatively similar way.
Performance of the predictive models
The multiple LR model can be seen in Eq. 8. The RF model was built as a 40-estimator forest, with a minimum of two samples in each final leaf. ANN’s final topology was 4–4–1, meaning 4 inputs in the input layer, 4 neurons in the hidden layer, and 1 output in the output layer. In the hidden layer, the activation function used was Rectified Linear Unit (ReLu) and the output function was the linear function. The difference between each activation function resides in the fact that the linear function is defined by a line, whereas ReLu, despite its name, is a nonlinear transfer function which is calculated as max(0.0, x), which means that, for negative inputs, it returns a value of zero and when the input is positive, it returns the same value.
Figures 8, 9 and 10 show experimental values against the predicted outputs of RF, LR and ANN, respectively. Similar to the aspect ratio plots, columns in these figures represent actual values, while cross markers refer to predicted values. Levels 1 to 5 indicate the increase in energy consumption (Table 1).
Likewise, as with aspect ratio, RF model performed worse than LR and ANN is the best model among them. Analyzing Fig. 8, it is visible that RF model missed multiple targets, mainly in TMP sample group, which is reflected in its R² of 0.8720, the poorest of all three models. MAE, MAPE and RSME also were the biggest ones, being: 1.358, 20.79% and 1.712, as displayed in Table 9. This behavior might be due to a couple of reasons, for instance the robustness of the RF algorithm, or maybe also due to the principle of function of this technique, which consists in averaging the target values of the train samples that fall into a specific range (Géron 2019). Figure 9 shows how LR predicted yields. It meets better the targets, but still not so precisely. Nevertheless, its R² is above 0.9, being 0.9255. It predicts better the TMP group than RF model did, although it does not quite fit the trend for points TMP_level_3, TMP_level_4 and TMP_level_5. Other groups were represented better in terms of tendencies related to increase of HPH energy and yield of nanofibrillation (%). MAE, MAPE and RSME for LR can be checked in Table 9. Again, ANN model presented the best results in terms of both performance and capturing of trends. It achieved the highest R² of 0.9749 and lowest MAE, MAPE and RSME, being 0.577, 6.74% and 0.758 respectively. From Fig. 10, it can be seen that it almost met all points precisely, as it effectively captured all group trends.
Similar conclusions inferred for aspect ratio can be drawn for nanofibrillation yield. For example, all models were able to grasp, some in a better level than others, the increase in yield when HPH energy increased too. Also, they were able to differentiate each group of samples, considering they belong to different treated pulps. Here, it is possible to state again that an increase in the complexity of the model resulted in a better tendency prediction. But this time, RF model did the poorest job, while LR operated reasonably and ANN performed very well. This same order is respected when it comes to comparing the prediction quality metrics.
Regarding the usefulness of these models, they could be applied in processes where either stable dispersions, homogeneous distribution, and low particle size are required, or in the opposite case, e.g., where nanocelluloses are used as adsorbents and need to be recovered by sedimentation or other means (Ho and Leo 2021). Indirectly, it is known that the yield of nanofibrillation exerts a positive influence on the tensile strength of nanocellulose-based films (Espinosa et al. 2020) and nanocellulose-reinforced paper sheets (Ehman et al. 2020).
Conclusions
In the current study, three different machine learning algorithms, namely multiple linear regression (LR), random forests (RF) and artificial neural networks (ANN), were applied in order to predict two important nanocellulose properties: aspect ratio and yield of nanofibrillation. Features required for obtaining satisfactory results were related mainly to the chemical composition of the pre-treated pulps, HPH intensity, and easy-to-measure nanocellulose parameters. The findings of the current work show that one can use different machine learning models to obtain pieces of information on yield and aspect ratio depending on the availability of measurements and sensors. Regarding the particularities of each property, the yield of nanofibrillation was more challenging to model than the aspect ratio of (L)CMNFs. Even though all models showed good performances, ANN outplayed RF and LR models in terms of the correlation coefficient (0.975 for yield, 0.96 for aspect ratio), MAE, MAPE, and RMSE. These results might be due to the greater complexity of the ANN model. However, the random forest approach used two factors less in the case of aspect ratio and one less in the case of yield of nanofibrillation, while still attaining an acceptable prediction power, at least for the morphological property. The overall indications are that machine learning algorithms have great potential in predicting these two important and often overlooked parameters for (L)CMNF suspensions, since very good results were obtained from relatively simple models and easily obtainable and low-cost inputs, not requiring advanced analytical techniques. The models obtained so far are a first step towards the aim of better controlling the production of nanocellulose. A limitation that must be highlighted here is the number of samples, which is quite low. Therefore, future steps involve the inclusion of more data to continuously improve the prediction and generalization capacity of the models. Also, it would be interesting to include in the model different types of pulps, coming from both wood and non-wood feedstock, and other types of pre-treatment.
Data availability
Raw data of the present work can be made available upon request.
References
Abdul Khalil HPS, Davoudpour Y, Islam MN et al (2014) Production and modification of nanofibrillated cellulose using various mechanical processes: a review. Carbohydr Polym 99:649–665. https://doi.org/10.1016/j.carbpol.2013.08.069
Aguado R, Moral A, López P et al (2016) Morphological analysis of pulps from orange tree trimmings and its relation to mechanical properties. Meas J Int Meas Confed. https://doi.org/10.1016/j.measurement.2016.06.063
Aguado R, Tarrés Q, Pèlach M et al (2022) Micro- and nanofibrillated cellulose from annual plant-sourced fibers: comparison between enzymatic hydrolysis and mechanical refining. Nanomaterials 12:1612. https://doi.org/10.3390/nano12091612
Alila S, Besbes I, Vilar MR et al (2013) Non-woody plants as raw materials for production of microfibrillated cellulose (MFC): a comparative study. Ind Crops Prod 41:250–259. https://doi.org/10.1016/j.indcrop.2012.04.028
Almonti D, Baiocco G, Tagliaferri V, Ucciardello N (2019) Artificial neural network in fibres length prediction for high precision control of cellulose refining. Materials 12:3730. https://doi.org/10.3390/ma12223730
Besbes I, Alila S, Boufi S (2011) Nanofibrillated cellulose from TEMPO-oxidized eucalyptus fibres: effect of the carboxyl content. Carbohydr Polym 84:975–983. https://doi.org/10.1016/j.carbpol.2010.12.052
Breiman L (2001) Random forests. Mach Learn 45:5–32. https://doi.org/10.1023/A:1010933404324
Dai Z, Ottesen V, Deng J et al (2019) A brief review of nanocellulose based hybrid membranes for CO2 separation. Fibers 7:40. https://doi.org/10.3390/fib7050040
Desmaisons J, Boutonnet E, Rueff M et al (2017) A new quality index for benchmarking of different cellulose nanofibrils. Carbohydr Polym 174:318–329. https://doi.org/10.1016/j.carbpol.2017.06.032
Ehman NV, Felissia FE, Tarrés Q et al (2020) Effect of nanofiber addition on the physical–mechanical properties of chemimechanical pulp handsheets for packaging. Cellulose 27:10811–10823. https://doi.org/10.1007/s10570-020-03207-5
Espinosa E, Rol F, Bras J, Rodríguez A (2020) Use of multi-factorial analysis to determine the quality of cellulose nanofibers: effect of nanofibrillation treatment and residual lignin content. Cellulose. https://doi.org/10.1007/s10570-020-03136-3
Géron A (2019) Hands-on machine learning with Scikit-learn, Keras, and TensorFlow, 2nd edn. O’Reilly Media, USA
Haykin S (1999) Neural networks: a comprehensive foundation, 2nd edn. Pearson Prentice Hall, Singapore
Ho NAD, Leo CP (2021) A review on the emerging applications of cellulose, cellulose derivatives and nanocellulose in carbon capture. Environ Res 197:111100. https://doi.org/10.1016/j.envres.2021.111100
Isogai A (2020) Cellulose nanofibers: recent progress and future prospects. J Fiber Sci Technol 76:310–326. https://doi.org/10.2115/fiberst.2020-0039
Kim JY, Zhou L, Morita N (2021) Study of degradable fibers with and without guar gum as a proppant transport agent using large-scale slot equipment. SPE J 26:262–280. https://doi.org/10.2118/195808-PA
Klemm D, Cranston ED, Fischer D et al (2018) Nanocellulose as a natural source for groundbreaking applications in materials science: today’s state. Mater Today 21:720–748. https://doi.org/10.1016/j.mattod.2018.02.001
Kriechbaum K, Munier P, Apostolopoulou-Kalkavoura V, Lavoine N (2018) Analysis of the porous architecture and properties of anisotropic nanocellulose foams: a novel approach to assess the quality of cellulose nanofibrils (CNFs). ACS Sustain Chem Eng 6:11959–11967. https://doi.org/10.1021/acssuschemeng.8b02278
Lee KY, Aitomäki Y, Berglund LA et al (2014) On the use of nanocellulose as reinforcement in polymer matrix composites. Compos Sci Technol 105:15–27. https://doi.org/10.1016/j.compscitech.2014.08.032
Leong SL, Tiong SIX, Siva SP et al (2022) Morphological control of cellulose nanocrystals via sulfuric acid hydrolysis based on sustainability considerations: an overview of the governing factors and potential challenges. J Environ Chem Eng 10:108145. https://doi.org/10.1016/j.jece.2022.108145
Li Z, Zhang H, Wang X et al (2016) Further understanding the response mechanism of lignin content to bonding properties of lignocellulosic fibers by their deformation behavior. RSC Adv 6:109211–109217. https://doi.org/10.1039/C6RA22457A
Maulud D, Abdulazeez AM (2020) A review on linear regression comprehensive in machine learning. J Appl Sci Technol Trends 1:140–147. https://doi.org/10.38094/jastt1457
Movsesyan A, Besteiro LV, Wang Z, Govorov AO (2022) Mie sensing with neural networks: recognition of nano-object parameters, the invisibility point, and restricted models. Adv Theory Simul 5:2100369. https://doi.org/10.1002/adts.202100369
Mugwagwa LR, Chimphango AFA (2022) Predicting mechanical properties of hemicellulose-based films reinforced with acetylated nanocellulose. J Polym Res 29:228. https://doi.org/10.1007/s10965-022-03092-5
Nader S, Brosse N, Khadraoui M et al (2022) A low-cost environmentally friendly approach to isolate lignin containing micro and nanofibrillated cellulose from Eucalyptus globulus bark by steam explosion. Cellulose 29:5593–5607. https://doi.org/10.1007/s10570-022-04632-4
Özkan M, Karakoç A, Borghei M et al (2019) Machine learning assisted design of tailor-made nanocellulose films: a combination of experimental and computational studies. Polym Compos 40:4013–4022. https://doi.org/10.1002/pc.25262
Pennells J, Heuberger B, Chaléat C, Martin DJ (2022) Assessing cellulose micro/nanofibre morphology using a high throughput fibre analysis device to predict nanopaper performance. Cellulose 29:2599–2616. https://doi.org/10.1007/s10570-021-04405-5
Raj P, Mayahi A, Lahtinen P et al (2016) Gel point as a measure of cellulose nanofibre quality and feedstock development with mechanical energy. Cellulose 23:3051–3064. https://doi.org/10.1007/s10570-016-1039-2
Sanchez-Salvador JL, Monte MC, Batchelor W et al (2020) Characterizing highly fibrillated nanocellulose by modifying the gel point methodology. Carbohydr Polym 227:115340. https://doi.org/10.1016/j.carbpol.2019.115340
Sanchez-Salvador JL, Campano C, Lopez-Exposito P et al (2021) Enhanced morphological characterization of cellulose nano/microfibers through image skeleton analysis. Nanomaterials. https://doi.org/10.3390/nano11082077
Sanchez-Salvador JL, Campano C, Negro C et al (2021) Increasing the possibilities of TEMPO-mediated oxidation in the production of cellulose nanofibers by reducing the reaction time and reusing the reaction medium. Adv Sustain Syst 5:2000277. https://doi.org/10.1002/adsu.202000277
Sanchez-Salvador JL, Monte MC, Negro C et al (2021) Simplification of gel point characterization of cellulose nano and microfiber suspensions. Cellulose 28:6995–7006. https://doi.org/10.1007/s10570-021-04003-5
Santos AF, Aguado R, Corazza ML et al (2022) Artificial neural network for aspect ratio prediction of lignocellulosic micro/nanofibers. Cellulose 29:5609–5622. https://doi.org/10.1007/s10570-022-04631-5
Segal L, Creely JJ, Martin AE, Conrad CM (1959) An empirical method for estimating the degree of crystallinity of native cellulose using the X-ray diffractometer. Text Res J 29:786–794. https://doi.org/10.1177/004051755902901003
Serra-Parareda F, Aguado R, Tarrés Q et al (2021a) Chemical-free production of lignocellulosic micro-and nanofibers from high-yield pulps: synergies, performance, and feasibility. J Clean Prod 313:127914. https://doi.org/10.1016/j.jclepro.2021.127914
Serra-Parareda F, Aguado R, Tarrés Q et al (2021b) Potentiometric back titration as a robust and simple method for specific surface area estimation of lignocellulosic fibers. Cellulose 28:10815–10825. https://doi.org/10.1007/s10570-021-04250-6
Serra-Parareda F, Tarrés Q, Mutjé P et al (2021c) Correlation between rheological measurements and morphological features of lignocellulosic micro/nanofibers from different softwood sources. Int J Biol Macromol 187:789–799. https://doi.org/10.1016/j.ijbiomac.2021.07.195
Serra-Parareda F, Aguado R, Arfelis S et al (2022) Techno-economic and environmental evaluation of a market pulp reinforced with micro-/nanofibers as a strengthening agent in packaging paper. J Clean Prod 347:131265. https://doi.org/10.1016/j.jclepro.2022.131265
Sluiter A, Hames B, Ruiz R et al (2012) Determination of structural carbohydrates and lignin in biomass
TAPPI (2020) TAPPI standards, technical information papers, and useful methods. Technical Association of the Pulp & Paper Industry, New York
Tarrés Q, Oliver-Ortega H, Alcalà M et al (2020) Research on the strengthening advantages on using cellulose nanofibers as polyvinyl alcohol reinforcement. Polymers. https://doi.org/10.3390/POLYM12040974
Tarrés Q, Oliver-Ortega H, Boufi S et al (2020) Evaluation of the fibrillation method on lignocellulosic nanofibers production from eucalyptus sawdust: a comparative study between high-pressure homogenization and grinding. Int J Biol Macromol 145:1199–1207. https://doi.org/10.1016/J.IJBIOMAC.2019.10.046
Torrents-Barrena J, Pellicer E (2021) Smart cellulose composites: advanced applications and properties prediction using machine learning. In: Reference module in materials science and materials engineering
Varanasi S, He R, Batchelor W (2013) Estimation of cellulose nanofibre aspect ratio from measurements of fibre suspension gel point. Cellulose 20:1885–1896. https://doi.org/10.1007/s10570-013-9972-9
Wang T, Wang X, Luo Z et al (2011) Mechanisms of viscosity increase for nanocolloidal dispersions. J Nanosci Nanotechnol 11:3141–3150. https://doi.org/10.1166/jnn.2011.3613
Wang W, Gu F, Deng Z et al (2021) Multilayer surface construction for enhancing barrier properties of cellulose-based packaging. Carbohydr Polym 255:117431. https://doi.org/10.1016/j.carbpol.2020.117431
Xu Y, Kuang Y, Salminen P, Chen G (2016) The influence of nano-fibrillated cellulose as a coating component in paper coating. BioResources 11:4342–4352
Acknowledgments
Authors wish to acknowledge the financial support of the funding agencies listed in the “Funding” section for their support to develop the present work. Authors’ information: Marc Delgado-Aguilar and Quim Tarrés are Serra Húnter Fellows.
Funding
Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. The present work has been funded by the Spanish Ministry of Science and Innovation, projects CON-FUTURO-ES (PID2020-113850RB-C22) and VALORCON-NC (PDC2021-120964-C22). Alexandre Ferreira Santos received funding from the Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq, Brazil) for his research stay at University of Girona. The Human Resources Program of the National Agency of Petroleum, Natural Gas and Biofuels (PRH-ANP/Finep) from Brazil has economically supported the grant of Giovana S. Iamin.
Author information
Authors and Affiliations
Contributions
All authors contributed to the study conception and design. Material preparation, data collection and analysis were performed by GSI, RA and QT. The first draft of the manuscript was written by GSI and RA, and all authors commented on previous versions of the manuscript. AFS, MLC, and MD-A compiled all comments and prepared the final version of the manuscript, which was read and approved by all the authors.
Corresponding author
Ethics declarations
Conflict of interest
Authors declare that they have no known competing interests or personal relationships that could have appeared to influence the work reported in this paper.
Ethical approval and consent to participate
Authors declare that the manuscript is not submitted to any other journal at the time of submission for simultaneous consideration, that the submitted work is original and has not been published elsewhere in any form, that this work is not part of a single study, that results are presented under the principles of honesty, without fabrication falsification or inappropriate data manipulation and that no data, text or theories by others are presented as our own.
Consent for publication
All authors have revised the last version of the submitted manuscript and we approve its submission.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Signori-Iamin, G., Santos, A.F., Corazza, M.L. et al. Prediction of cellulose micro/nanofiber aspect ratio and yield of nanofibrillation using machine learning techniques. Cellulose 29, 9143–9162 (2022). https://doi.org/10.1007/s10570-022-04847-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10570-022-04847-5