Abstract
The addition of thermoplastic to thermosetting matrix systems has been proposed as a successful strategy to produce polymers with self-healing ability. Curing mechanism of diglycidyl ether of bisphenol A/triethylene-tetramine epoxy system modified with poly(ethylene-co-methacrylic acid) (EMAA) thermoplastic healing agent was investigated in this work. The effects of thermoplastic content, particle size and dispersion on thermomechanical properties were studied. Specimens were produced with 5 wt. %, 10 wt. % and 15 wt.% EMAA with particle sizes ≤ 125 μm or ≤ 425 μm. The addition of thermoplastic produced a reduction in E’ of about 27% for samples with particles ≤ 125 μm and about 45% for samples with particles ≤ 425 μm. Samples with particle size ≤ 125 μm showed a reduction in Tg of up to 37 °C as compared to neat epoxy. In the case of samples with particle size ≤ 425 μm, no direct correlation between Tg and mass fraction of added EMAA is found. Thus, particle size played an important role on thermomechanical properties and cure kinetics of epoxy. The greater the interfacial area, the greater was the change in final properties as compared to the unmodified material. It was also observed that the mass fraction and particle size can interfere in the curing reactions, where results suggest deceleration when smaller particles (≤ 125 μm) are added in larger fractions and acceleration with increasing mass fraction of larger particles (≤ 425 μm). All experimental reactions could be fit to the autocatalytic Sourour and Kamal model with good agreement; the model was able to predict the effects of thermoplastic addition in different particle sizes and mass fractions.
Similar content being viewed by others
References
Sumesh KR and Kanthavel K (2020) Grey relational optimization for factors influencing tensile, flexural, and impact properties of hybrid sisal banana fiber epoxy composites. J Indust Text 1–19
Sumesh KR and Kanthavel K (2020) Optimizing various parameters influencing mechanical properties of banana/coir natural fiber composites using grey relational analysis and artificial neural network models. J Indust Text 1-23
Sumesh KR, Kavinami V, Rajeshkumar G, Pavikumar P and Idran S (2020) An investigation into the mechanical and wear characteristics of hybrid composites: influence of different types and content of biodegradable reinforcements. J Nat Fiberss 1-13
Sumesh KR, Kavimani V, Rajeshkumar G, Indran S, Khan A (2020) Mechanical, water absorption and wear characteristics of novel polymeric composites: impact of hybrid natural fibers and oil cake filler addition. J Indust Textss 1-28s
Barbosa APC, Fulco APP, Guerra ESS, Arakaki FK, Tosatto M, Costa MCB, Melo JDD (2017) Accelerated aging effects on carbon fibber/epoxy composites. Compos Part B Eng 110:298–306
Dell’Olio C, Yuan Q, Varley RJ (2015) Epoxy/poly(ethylene-co-methacrylic acid) blends as thermally activated healing agents in an epoxy/amine. Macromol Mater Eng 300:70–79
Varley RJ, Craze DA, Mouritz AP and Wang WH (2013) Thermoplastic Healing in Epoxy Networks: Exploring Performance and Mechanism of Alternative Healing Agents Macromol Mater Eng,
Pascault JP, Williams RJJ (2010) Epoxy Polymers: New Materials and Innovations, 1st edn. Wiley-VCH, Weinheim
Loh TW, Ladani RB, Orifici A, Kandare E (2021) Ultra-tough and in-situ repairable carbon/epoxy composite with EMAA. Compos Part A ApplSciManufact 143:106206
Zhang F, Zhang L, Yaseen M, Huang K (2020) A review on the self-healing ability of epoxy polymers . ApplPolym 138:1–14
Loh TW, Ladani RB, Kandare E (2020) Intralaminar toughened carbon/epoxy composites exhibiting self-healing capabilities. International Conference on Composite Materials, Non-Serials, 1214–1222
Wu WY, Meure S, Solomon D (2008) Self-healing polymeric materials: a review of recent developments. ProgPolymSci 33:479–522
Hayes SA, Zhang W, Branthwaite M, Jones FR (2007) Self-healing of damage in fibre-reinforced polymer-matrix composites. J R Soc Interface 4:381–387
Meure S, Wu DY, Furman S (2010) FTIR study of bonding between a thermoplastic healing agent and a mendable epoxy resin. VibSpectrosc 52:10–15
Zako M, Takano N (1999) Intelligent material systems using epoxy particles to repair microcracks and delamination damage GFRP. J Intel Mat SystStr 10:836–841
Xie X-L, Mai Y-W, Zhou X-P (2005) Dispersion and alignment of carbon nanotubes in polymer matrix: a review. Mater SciEng 49:89–112
Bilyeu B, Brostow W, Menard K (2001) Epoxy thermosets and their applications II thermal analysis. J Mater Edus 23(189):204
Ton-That MT, Ngo TD, Ding P, Fang G, Cole KC, Hoa SV (2004) Epoxy nanocomposites: analysis and kinetics of cure. PolymEngSci 44:1132–1141
Yousefi A, Lafleur PG (1997) Kinetic studies of thermoset cure reactions: a review. Polym Compos 18:157–168
Silva BL, Schuster MB, Bello RH, Becker D and Coelho LAF (2020) The effects of carbon nanoparticles on curing kinetics of epoxy modified with triblock copolymer. Polym Bull
Meure S, Varley RJ, Wu DYW, Mayo S, Nairn K, Furman S (2012) Confirmation of the healing mechanism in a mendable EMAA–epoxy resin. EurPolym J 48:524–531
Varley RJ, Harve FC (2012) EMAA as a healing agent for mendable high temperature epoxy amine thermosets. Composites: part A 43 1073–1080
Meister S, Drummer D (2013) Influence of manufacturing conditions on measurement of mechanical material properties on thermoplastic micro tensile bars. Polym Testing 32(432):437
Kamal MR, Souror S (1973) Kinetics and thermal characterization of thermoset cure. PolymEngSci 13(59):64
Nascimento AA, Fernandez F, Silva FF, Ferreira EPC, Melo JD and Barbosa AP (2020)s Addition of poly (ethylene-co-methacrylic acid)(EMAA) as self-healing agent to carbon-epoxy composites Composites Part A: 137.
Idicula M, Malhotra SK, Kuruvilla J, Thomas S (2005) Dynamic mechanical analysis of randomly oriented intimately mixed short banana/sisal hybrid fibre reinforced polyester composites. Compos SciTechnol 65(1077):1087s
Ornaghi LH, Silva HSP, Zattera JA, Amico SC (2011) Hybridization effect on the mechanical and dynamic mechanical properties of curaua composites. Mater SciEng 528(7285):7289
Larrañaga M, Martin MD, Gabilondo N, Kortaberia G, Riccardi CC, Mondragon I (2004) Cure kinetics of epoxy systems modified with block copolymers. PolymInt 53(1495):1502
Silva BL, Bello RH, Coelho LA (2018) The role of the ratio (PEG: PPG) of a triblock copolymer (PPG-b-PEG-b-PPG) in the cure kinetics, miscibility and thermal and mechanical properties in an epoxy matrix. PolymInt 67(1248):1255s
Kim SD, Kim SC (1994) Rubber modified epoxy resin I: cure kinetics and chemorheology. Pol EngSci 34:166
Kalista SJ, Ward TC (2007) Thermal characteristics of the self-healing response in poly(ethylene-co-methacrylic acid) copolymers. Soc Interface 4(405):411
Meure S, Wu DY, Furman S (2009) Polyethylene-co-methacrylic acid healing agents for mendable epoxy resins. Acta Mater 57(4312):4320
Nishida H, Ueda H, Matsuda S, Kishi H, Murakami A (2007) Formation of glass transition temperature-less (Tg-less) composite with epoxy resin and ionomer. Asia-Pac J ChemEng 2(63):69
Acknowledgements
This study was financed in part by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior—Brasil (CAPES)—Finance Code 001. The research was also supported by the National Council for Scientific and Technological Development (CNPq), grant number 426837/2016-9. The authors are grateful to Professor Dr. César Edil da Costa for DSC tests, carried out at the State University of Santa Catarina-UDESC.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Silva, B.L., Gomes de Moura Filho, C., Diniz Melo, J.D. et al. The role of poly (ethylene-co-methacrylic acid) (EMAA) on cure kinetics and thermomechanical properties of epoxy. Polym. Bull. 79, 3291–3307 (2022). https://doi.org/10.1007/s00289-021-03650-9
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00289-021-03650-9