Skip to main content
SpringerLink
Log in

Effects of welding parameters and thermal insulation on the mechanical behavior and microstructure of friction lap-welded aluminum to glass fiber–reinforced thermoset composite with a thermoplastic PA6 interlayer

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Friction lap welding was used to join aluminum with glass fiber–reinforced thermoset polymer (GFRP) using a thermoplastic interlayer. The effect of different welding parameters on joint strength and fracture surfaces was investigated, and the optimal welding parameters were determined using the Taguchi method. Results revealed that low heat generation led to weak mechanical interlocking between GFRP and the thermoplastic interlayer, while high heat generation caused degradation of the aluminum/thermoplastic polymer interface. The tool traverse speed was found to be the most influential parameter in terms of joint strength, followed by plunge depth and rotational speed. Moreover, thermal measurements were conducted during the welding process using thermocouples. An uneven thermal distribution was discovered across the overlap area due to dissimilar substrates. This issue was resolved by incorporating aluminum thermal insulation, resulting in improved heat distribution and a significant enhancement of 94% in joint strength. Scanning electron microscopy (SEM) was employed to identify joining mechanisms and examine the effect of welding parameters on joint microstructure. Furthermore, Fourier-transform infrared spectroscopy (FTIR) was used to investigate chemical bond formation at the aluminum/thermoplastic polymer interface. The results showed that the joining mechanisms involved mechanical interlocking between the thermoplastic interlayer and aluminum, as well as chemical bonding, penetration, and intertwining between the thermoplastic interlayer and the thermoset composite.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15

Similar content being viewed by others

References

  1. Jiang B, Chen Q, Yang J (2020) Advances in joining technology of carbon fiber-reinforced thermoplastic composite materials and aluminum alloys. Int J Adv Manuf Technol 110:2631–2649. https://doi.org/10.1007/s00170-020-06021-2

    Article  Google Scholar 

  2. El EH, Korkmaz ME, Gupta MK et al (2022) A state-of-the-art review on mechanical characteristics of different fiber metal laminates for aerospace and structural applications. Int J Adv Manuf Technol 123:2965–2991. https://doi.org/10.1007/s00170-022-10277-1

    Article  Google Scholar 

  3. Cole GS, Sherman AM (1995) Light weight materials for automotive applications. Mater Charact 35:3–9. https://doi.org/10.1016/1044-5803(95)00063-1

    Article  Google Scholar 

  4. Goushegir SM, dos Santos JF, Amancio-Filho ST (2016) Failure and fracture micro-mechanisms in metal-composite single lap joints produced by welding-based joining techniques. Compos Part A Appl Sci Manuf 81:121–128. https://doi.org/10.1016/j.compositesa.2015.11.001

    Article  Google Scholar 

  5. Temesi T, Czigany T (2020) Integrated structures from dissimilar materials: the future belongs to aluminum–polymer joints. Adv Eng Mater 22:2000007. https://doi.org/10.1002/adem.202000007

    Article  Google Scholar 

  6. Cakir MV, Kinay D (2021) MWCNT, nano-silica, and nano-clay additives effects on adhesion performance of dissimilar materials bonded joints. Polym Compos 42:5880–5892. https://doi.org/10.1002/pc.26268

    Article  Google Scholar 

  7. Aamir M, Tolouei-Rad M, Giasin K, Nosrati A (2019) Recent advances in drilling of carbon fiber–reinforced polymers for aerospace applications: a review. Int J Adv Manuf Technol 105:2289–2308. https://doi.org/10.1007/s00170-019-04348-z

    Article  Google Scholar 

  8. Amancio-Filho ST, Dos Santos JF (2009) Joining of polymers and polymer–metal hybrid structures: recent developments and trends. Polym Eng Sci 49:1461–1476. https://doi.org/10.1002/pen.21424

    Article  Google Scholar 

  9. Kweon J-H, Jung J-W, Kim T-H et al (2006) Failure of carbon composite-to-aluminum joints with combined mechanical fastening and adhesive bonding. Compos Struct 75:192–198. https://doi.org/10.1016/j.compstruct.2006.04.013

    Article  Google Scholar 

  10. Baldan A (2004) Adhesively-bonded joints in metallic alloys, polymers and composite materials: mechanical and environmental durability performance. J Mater Sci 39:4729–4797. https://doi.org/10.1023/B:JMSC.0000035317.87118.ab

    Article  Google Scholar 

  11. Haghshenas M, Khodabakhshi F (2019) Dissimilar friction-stir welding of aluminum and polymer: a review. Int J Adv Manuf Technol 104:333–358. https://doi.org/10.1007/s00170-019-03880-2

    Article  Google Scholar 

  12. Li H, Chen C, Yi R et al (2022) Ultrasonic welding of fiber-reinforced thermoplastic composites: a review. Int J Adv Manuf Technol 120:29–57. https://doi.org/10.1007/s00170-022-08753-9

    Article  Google Scholar 

  13. Amancio-Filho ST, Bueno C, Dos Santos JF et al (2011) On the feasibility of friction spot joining in magnesium/fiber-reinforced polymer composite hybrid structures. Mater Sci Eng A 528:3841–3848. https://doi.org/10.1016/j.msea.2011.01.085

    Article  Google Scholar 

  14. Baffari D, Buffa G, Campanella D et al (2018) Experimental and numerical investigation on a new FSW based metal to composite joining technique. J Manuf Process 34:758–764. https://doi.org/10.1016/j.jmapro.2018.03.048

    Article  Google Scholar 

  15. Dalwadi CG, Patel AR, Kapopara JM et al (2018) Examination of mechanical properties for dissimilar friction stir welded joint of Al alloy (AA-6061) to PMMA (Acrylic). Mater Today Proc 5:4761–4765. https://doi.org/10.1016/j.matpr.2017.12.049

    Article  Google Scholar 

  16. Liu FC, Dong P (2019) Promising high-speed welding techniques for joining polymers to metals and underlying joining mechanisms. In: Friction stir welding and processing X. Springer, 13–22. https://doi.org/10.1007/978-3-030-05752-7_2

  17. Ma N, Geng P, Ma Y et al (2021) Thermo-mechanical modeling and analysis of friction spot joining of Al alloy and carbon fiber-reinforced polymer. J Market Res 12:1777–1793. https://doi.org/10.1016/j.jmrt.2021.03.111

    Article  Google Scholar 

  18. Patel AR, Kotadiya DJ, Kapopara JM et al (2018) Investigation of mechanical properties for hybrid joint of aluminium to polymer using friction stir welding (FSW). Mater Today Proc 5:4242–4249. https://doi.org/10.1016/j.matpr.2017.11.688

    Article  Google Scholar 

  19. Rao PVCS, Mounika E, Vikram G (2019) Process parameters optimization on FSW of polycarbonate and AA6061. Mater Today Proc 19:637–641. https://doi.org/10.1016/j.matpr.2019.07.745

    Article  Google Scholar 

  20. Yan Y, Shen Y, Lei H et al (2020) Friction lap welding AA6061 alloy and GFR nylon: Influence of welding parameters and groove features on joint morphology and mechanical property. J Mater Process Technol 278:116458. https://doi.org/10.1016/j.jmatprotec.2019.116458

    Article  Google Scholar 

  21. Wu LH, Nagatsuka K, Nakata K (2018) Direct joining of oxygen-free copper and carbon-fiber-reinforced plastic by friction lap joining. J Mater Sci Technol 34:192–197. https://doi.org/10.1016/j.jmst.2017.10.019

    Article  Google Scholar 

  22. Xie Y, Huang Y, Meng X et al (2020) Friction stir spot welding of aluminum and wood with polymer intermediate layers. Constr Build Mater 240:117952. https://doi.org/10.1016/j.conbuildmat.2019.117952

    Article  Google Scholar 

  23. Geng P, Ma N, Ma H et al (2022) Flat friction spot joining of aluminum alloy to carbon fiber reinforced polymer sheets: experiment and simulation. J Mater Sci Technol 107:266–289. https://doi.org/10.1016/j.jmst.2021.08.043

    Article  Google Scholar 

  24. Giurgiutiu V (2022) Stress, vibration, and wave analysis in aerospace composites: SHM and NDE applications. Academic Press

  25. Gebrehiwet L, Abate E, Negussie Y, et al Application of composite materials in aerospace & automotive industry. https://doi.org/10.35629/5252-0503697723

  26. Gaitonde VN, Karnik SR, Mata F, Davim JP (2010) Modeling and analysis of machinability characteristics in PA6 and PA66 GF30 polyamides through artificial neural network. J Thermoplast Compos Mater 23:313–336. https://doi.org/10.1177/0892705709349319

    Article  Google Scholar 

  27. Derazkola HA, Kashiry Fard R, Khodabakhshi F (2018) Effects of processing parameters on the characteristics of dissimilar friction-stir-welded joints between AA5058 aluminum alloy and PMMA polymer. Weld World 62:117–130. https://doi.org/10.1007/s40194-017-0517-y

    Article  Google Scholar 

  28. Choi J-W, Morisada Y, Liu H et al (2020) Dissimilar friction stir welding of pure Ti and carbon fibre reinforced plastic. Sci Technol Weld Join 25:600–608. https://doi.org/10.1080/13621718.2020.1788814

    Article  Google Scholar 

  29. Huang Y, Meng X, Wang Y et al (2018) Joining of aluminum alloy and polymer via friction stir lap welding. J Mater Process Technol 257:148–154. https://doi.org/10.1016/j.jmatprotec.2018.02.043

    Article  Google Scholar 

  30. Lambiase F, Grossi V, Di Ilio A, Paoletti A (2020) Feasibility of friction stir joining of polycarbonate to CFRP with thermosetting matrix. Int J Adv Manuf Technol 106:2451–2462. https://doi.org/10.1007/s00170-019-04814-8

    Article  Google Scholar 

  31. Ashong AN, Lee M, Hong S-T et al (2021) Refill friction stir spot welding of dissimilar AA6014 Al alloy and carbon-fiber-reinforced polymer composite. Met Mater Int 27:639–649. https://doi.org/10.1007/s12540-020-00788-5

    Article  Google Scholar 

  32. Liu FC, Dong P, Lu W, Sun K (2019) On formation of AlOC bonds at aluminum/polyamide joint interface. Appl Surf Sci 466:202–209. https://doi.org/10.1016/j.apsusc.2018.10.024

    Article  Google Scholar 

  33. Lim M-Y, Kim HJ, Baek SJ et al (2014) Improved strength and toughness of polyketone composites using extremely small amount of polyamide 6 grafted graphene oxides. Carbon N Y 77:366–378. https://doi.org/10.1016/j.polymdegradstab.2012.01.017

    Article  Google Scholar 

  34. Huang Y, Meng X, Xie Y et al (2018) Friction stir welding/processing of polymers and polymer matrix composites. Compos Part A Appl Sci Manuf 105:235–257. https://doi.org/10.1016/j.compositesa.2017.12.005

    Article  Google Scholar 

  35. Cross AD, Jones RA (1969) An introduction to practical infra-red spectroscopy. (No Title). https://doi.org/10.1007/978-1-4899-6596-7

  36. Porubská M, Szöllős O, Kóňová A et al (2012) FTIR spectroscopy study of polyamide-6 irradiated by electron and proton beams. Polym Degrad Stab 97:523–531

    Article  Google Scholar 

  37. Öhman M, Persson D, Leygraf C (2006) In situ ATR-FTIR studies of the aluminium/polymer interface upon exposure to water and electrolyte. Prog Org Coat 57:78–88. https://doi.org/10.1016/j.porgcoat.2006.07.002

    Article  Google Scholar 

  38. Farmer VC (1974) The infrared spectra of minerals. Mineral Soc Monogr 4:331–363

    Google Scholar 

  39. Ahern AM, Schwartz PR, Shaffer LA (1992) Characterization of conversion-coated aluminum using Fourier transform infrared and Raman spectroscopies. Appl Spectrosc 46:1412–1419. https://opg.optica.org/as/abstract.cfm?uri=as-46-9-1412

  40. Zhao S, Kimura F, Wang S, Kajihara Y (2021) Chemical interaction at the interface of metal–plastic direct joints fabricated via injection molded direct joining. Appl Surf Sci 540:148339. https://doi.org/10.1016/j.apsusc.2020.148339

    Article  Google Scholar 

  41. Ma Y, Zhou T, Su G et al (2016) Understanding the crystallization behavior of polyamide 6/polyamide 66 alloys from the perspective of hydrogen bonds: projection moving-window 2D correlation FTIR spectroscopy and the enthalpy. RSC Adv 6:87405–87415. https://doi.org/10.1039/C6RA09611E

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Adhesively Bonded and Sandwich Structures Research Laboratory, School of Mechanical Engineering, Iran University of Science and Technology, Narmak, Tehran, 16846-13114, Iran

    Mahdi Sahranavard & Hadi Khoramishad

Authors
  1. Mahdi Sahranavard
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Hadi Khoramishad
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Hadi Khoramishad.

Ethics declarations

Conflict of interest

The authors declare no competing interests.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Sahranavard, M., Khoramishad, H. Effects of welding parameters and thermal insulation on the mechanical behavior and microstructure of friction lap-welded aluminum to glass fiber–reinforced thermoset composite with a thermoplastic PA6 interlayer. Int J Adv Manuf Technol 132, 727–743 (2024). https://doi.org/10.1007/s00170-024-13413-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-024-13413-1

Keywords

Search

Navigation