Skip to main content
SpringerLink
Log in

Study on the magnetic abrasive finishing process using alternating magnetic field: investigation of mechanism and applied to aluminum alloy plate

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

In order to achieve the finishing of complex microsurface, the magnetic abrasive finishing process using alternating magnetic field was proposed. In this paper, the mechanism of the magnetic abrasive finishing process using alternating magnetic field was investigated. At the same time, the influence of magnetic particle size and magnetic field frequency on magnetic cluster changes was observed and the relationship between finishing force and alternating magnetic field was analyzed. In addition, the feasibility of ultraprecision finishing of 5052 aluminum alloy plate through this process was studied, and the influence of relevant process parameters on the finishing characteristics was analyzed. The experimental results show that the surface roughness of 5052 aluminum alloy plate improved from 318 to 3 nm Ra in 15 min.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Wu JZ, Zou YH, Sugiyama H (2015) Study on ultra-precision magnetic abrasive finishing process using low frequency alternating magnetic field. J Magn Magn Mater 386:50–59

    Article  Google Scholar 

  2. Jain VK (2009) Magnetic field assisted abrasive based micro-/nano-finishing. J Mater Process Technol 209(20):6022–6038

    Article  Google Scholar 

  3. Wu JZ, Zou YH, Sugiyama H (2016) Study on finishing characteristics of magnetic abrasive finishing process using low-frequency alternating magnetic field. Int J Adv Manuf Technol 85(1–4):585–594

    Article  Google Scholar 

  4. Zou YH, Xie HJ, Dong CW, Wu JZ (2018) Study on complex micro surface finishing of alumina ceramic by the magnetic abrasive finishing process using alternating magnetic field. Int J Adv Manuf Technol 97(5–8):2193–2202

    Article  Google Scholar 

  5. Shinmura T, Takazawa K, Hatano E (1985) Study on magnetic abrasive process: application to plane finishing. Bull Jpn Soc Precis Eng 19(4):289–294

    Google Scholar 

  6. Shinmura T, Aizawa T (1989) Study on magnetic abrasive finishing process-development of plane finishing apparatus using a stationary type electromagnet. Bull Jpn Soc Precis Eng 23(3):236–239

    Google Scholar 

  7. Kwak JS (2012) Mathematical model determination for improvement of surface roughness in magnetic-assisted abrasive polishing of nonferrous AISI316 material. Trans Nonferrous Metals Soc China 22:s845–s850

    Article  Google Scholar 

  8. Shinmura T, Takazawa K, Hatano E, Matsunaga M, Matsuo T (1990) Study on magnetic abrasive finishing. CIRP Ann 39(1):325–328

    Article  Google Scholar 

  9. Shinmura T, Takazawa K, Hatano E (1985) Study on magnetic abrasive process: application to edge finishing. Bull Jpn Soc Precis Eng 19(3):218–220

    Google Scholar 

  10. Yamaguchi H, Shinmura T, Kaneko T (1996) Development of a new internal finishing process applying magnetic abrasive finishing by use of pole rotation system. Int J Jpn Soc Precis Eng 30(4):317–322

    Google Scholar 

  11. Yamaguchi H, Shinmura T (2000) Study of an internal magnetic abrasive finishing using a pole rotation system: discussion of the characteristic abrasive behavior. Precis Eng 24:237–244

    Article  Google Scholar 

  12. Jain VK, Kumar P, Behera PK, Jayaswal SC (2001) Effect of working gap and circumferential speed on the performance of magnetic abrasive finishing process. Wear 250(1–12):384–390

    Article  Google Scholar 

  13. Jain VK, Saren KK, Raghuram V, Ravi Sankar M (2016) Force analysis of magnetic abrasive nano-finishing of magnetic and non-magnetic materials. Int J Adv Manuf Technol:1–11

  14. Yin S, Shinmura T (2004) Vertical vibration-assisted magnetic abrasive finishing and deburring for magnesium alloy. Int J Mach Tool Manu 44(12–13):1297–1303

    Article  Google Scholar 

  15. Zou YH, Jiao AY, Aizawa T (2010) Study on plane magnetic abrasive finishing process: experimental and theoretical analysis on polishing trajectory. Adv Mater Res 126:1023–1028

    Article  Google Scholar 

  16. Jiao AY, Quan HJ, Li ZZ, Zou YH (2015) Study on improving the trajectory to elevate the surface quality of plane magnetic abrasive finishing. Int J Adv Manuf Technol 80(9–12):1613–1623

    Article  Google Scholar 

  17. Sun X, Zou YH (2017) Development of magnetic abrasive finishing combined with electrolytic process for finishing SUS304 stainless steel plane. Int J Adv Manuf Technol 92(9–12):3373–3384

    Article  Google Scholar 

  18. Perez OR, Valdez S, Molina A, Mejia-Sintillo S, Garcia-Perez C, Salinas-Bravo VM, Gonzalez-Rodriguez JG (2017) Corrosion behavior of Al–Mg–Zn-Si alloy matrix composites reinforced with Y2O3 in 3.5% NaCl solution. Int J Electrochem Sci 12:7300–7311

    Article  Google Scholar 

  19. Wang FB, Liu JK, Li LL, Shu QL (2017) Green machining of aluminum honeycomb treated using ice fixation in cryogenic. Int J Adv Manuf Technol 92(1–4):943–952

    Article  Google Scholar 

  20. Barekar NS, Dhindaw BK (2014) Twin-roll casting of aluminum alloys – an overview. Mater Manuf Process 29(6):651–662

    Article  Google Scholar 

  21. Ding M, Zhang PL, Zhang ZY, Yao S (2010) A novel assembly technology of aluminum alloy honeycomb structure. Int J Adv Manuf Technol 46(9–12):1253–1258

    Google Scholar 

  22. Dursun T, Soutis C (2014) Recent developments in advanced aircraft aluminium alloys. Mater Des 56:862–871

    Article  Google Scholar 

  23. Shinmura T, Aizawa T (1989) Study on internal finishing of non-ferromagnetic tubing by magnetic abrasive machining process. Bull Jpn Soc Precis Eng 23(1):37–41

    Google Scholar 

  24. Jiles D (2015) Introduction to magnetism and magnetic materials. CRC press, Boca Raton, FL, USA

Download references

Author information

Authors and Affiliations

  1. Graduate School of Engineering, Utsunomiya University, 7-1-2Yoto, Utsunomiya, Tochigi, 321-8585, Japan

    Huijun Xie, Yanhua Zou & Chaowen Dong

  2. School of Mechanical Engineering & Automation, University of Science and Technology LiaoNing, Anshan, 114044, China

    Jinzhong Wu

Authors
  1. Huijun Xie
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Yanhua Zou
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Chaowen Dong
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Jinzhong Wu
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Yanhua Zou.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Xie, H., Zou, Y., Dong, C. et al. Study on the magnetic abrasive finishing process using alternating magnetic field: investigation of mechanism and applied to aluminum alloy plate. Int J Adv Manuf Technol 102, 1509–1520 (2019). https://doi.org/10.1007/s00170-018-03268-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-018-03268-8

Keywords

Search

Navigation