Abstract
LIGA process was carried out to fabricate the copper mold insert for a micro piezoelectric array. X-ray mask was fabricated using UV lithography and PMMA which is the X-ray photoresist was bonded to the titanium substrate done lapping. The bonded PMMA was exposed to X-ray exposure with the total amount of 4.0 kJ/cm3. Copper was then electroplated above the PMMA. After the post-processing, the copper mold insert with the pattern size 400 μm, the height 924 μm, was fabricated. To replicate the patterned micro rod array, PIM process was used. The entire optimized PIM process corresponding to the previous research was applied. The fabricated copper mold insert was used in injection molding process. The ejection pins were also fabricated using the same LIGA process for metal mold and used to extract the injection-molded specimens. After injection molding, two-step debinding and sintering processes were conducted and finally, micro piezoelectric rod array with a pattern size of 322 μm was fabricated without any defects such as collapse and break. The dimension accuracy was ensured through the SEM image analysis and dilatometry results. The physical and piezoelectric properties of sintered part were measured to confirm the part performance made by PIM process. Results indicated the possibility of using the metal mold for mass production system to produce the micro piezoelectric rod array.
Similar content being viewed by others
References
Haertling GH (1999) Ferroelectric ceramics: history and technology. J Am Ceram Soc 82:797–818. https://doi.org/10.1111/j.1151-2916.1999.tb01840.x
Yang Z, Hou Y, Pan H, Chang Y (2009) Structure, microstructure and electrical properties of (1− x− y) Bi0. 5Na0. 5TiO3–xBi0. 5K0. 5TiO3–yBi0. 5Li0. 5TiO3 lead-free piezoelectric ceramics. J Alloys Compd 480:246–253. https://doi.org/10.1016/j.jallcom.2009.02.030
Cheng SY, Fu SL, Wei CC (1987) Low-temperature sintering of PZT ceramics. Ceram Int 13:223–231. https://doi.org/10.1016/0272-8842(87)90066-6
Gallego-Juarez JA (1989) Piezoelectric ceramics and ultrasonic transducers. J Phys E: Sci Instrum 22:804–816
Dongyu X, Xin C, Hongda G, Fan L, Shifeng H (2015) Design, fabrication and properties of 1–3 piezoelectric ceramic composites with varied piezoelectric phase distribution. Ceram Int 41:9433–9442. https://doi.org/10.1016/j.ceramint.2015.03.324
Smith WA, Auld BA (1991) Modeling 1-3 composite piezoelectrics: thickness-mode oscillations. IEEE Trans Ultrason Ferroelectr Freq Control 38:40–47. https://doi.org/10.1109/58.67833
Janas VF, Safari A (1995) Overview of fine-scale piezoelectric ceramic/polymer composite processing. J Am Ceram Soc 78:2945–2955. https://doi.org/10.1111/j.1151-2916.1995.tb09068.x
Wang S, Li JF, Wakabayashi K, Esashi M, Watanabe R (1999) Lost silicon mold process for PZT microstructures. Adv Mater 11:873–876. https://doi.org/10.1002/(SICI)1521-4095(199907)11:10<873::AID-ADMA873>3.0.CO;2-F
Park JS, Lee SH, Park SS, Cho JW, Jung SW, Han JH, Kang SG (2003) Acoustic and electromechanical properties of 1–3 PZT composites for ultrasonic transducer arrays fabricated by sacrificial micro PMMA mold. Sensors Actuator A Phys 108:206–211. https://doi.org/10.1016/S0924-4247(03)00362-5
Zhou D, Lam KH, Chen Y, Zhang Q, Chiu YC, Luo H, Dai J, Chan HLW (2012) Lead-free piezoelectric single crystal based 1–3 composites for ultrasonic transducer applications. Sensors Actuator A Phys 182:95–100. https://doi.org/10.1016/j.sna.2012.05.030
Han JS, Gal CW, Park JM, Kim JH, Lee SH, Yeo BW, Park SJ (2018) Powder injection molding process for fabrication of piezoelectric 2D array ultrasound transducer. Smart Mater Struct 27:075058. https://doi.org/10.1088/1361-665X/aab27c
Han JS, Gal CW, Kim JH, Park SJ (2016) Fabrication of high-aspect-ratio micro piezoelectric array by powder injection molding. Ceram Int 42:9475–9481. https://doi.org/10.1016/j.ceramint.2016.03.011
Han JS, Oh KH, Moon WK, Kim K, Joh C, Seo HS, Bollina R, Park SJ (2015) Bio-inspired piezoelectric artificial hair cell sensor fabricated by powder injection molding. Smart Mater Struct 24:125025. https://doi.org/10.1088/0964-1726/24/12/125025
Bowen LJ, French KW (1992) Fabrication of piezoelectric ceramic/polymer composites by injection molding. In Applications of Ferroelectrics, 1992. ISAF’92., Proceedings of the Eighth IEEE International Symposium on. IEEE, p 160–163. https://doi.org/10.1109/ISAF.1992.300651
Wang MW (2010) Microceramic injection molding of a multilayer micropatterned micropart. Int J Adv Manuf Technol 51:145–153. https://doi.org/10.1007/s00170-010-2597-3
Fu G, Tor S, Loh N, Tay B, Hardt DE (2007) A micro powder injection molding apparatus for high aspect ratio metal micro-structure production. J Micromech Microeng 17:1803–1809. https://doi.org/10.1088/0960-1317/17/9/008
Kim JH, Choi SY, Jeon JH, Lim G, Chang SS (2013) Manufacture of a micro-sized piezoelectric ceramic structure using a sacrificial polymer mold insert. Microsyst Technol 19:343–349. https://doi.org/10.1007/s00542-012-1590-1
German RM, Bose A (1997) Injection molding of metals and ceramics. Metal Powder Industries Federation, Princeton
Heaney DF (2012) Handbook of metal injection molding. Elsevier
Qin Y, Brockett A, Ma Y, Razali A, Zhao J, Harrison C, Pan W, Dai X, Loziak D (2010) Micro-manufacturing: research, technology outcomes and development issues. Int J Adv Manuf Technol 47:821–837. https://doi.org/10.1007/s00170-009-2411-2
Becker E, Ehrfeld W, Hagmann P, Maner A, Münchmeyer D (1986) Fabrication of microstructures with high aspect ratios and great structural heights by synchrotron radiation lithography, galvanoforming, and plastic moulding (LIGA process). Microelectron Eng 4:35–56. https://doi.org/10.1016/0167-9317(86)90004-3
Malek CK, Saile V (2004) Applications of LIGA technology to precision manufacturing of high-aspect-ratio micro-components and-systems: a review. Microelectron J 35:131–143. https://doi.org/10.1016/j.mejo.2003.10.003
Nishiyabu K, Kanoko Y, Tanaka S (2007) Innovations in micro metal injection molding process by lost form technology. In Materials science forum. Trans Tech Publications 534:369–372. https://doi.org/10.4028/www.scientific.net/MSF.534-536.369
Katoh T, Tokuno R, Zhang Y, Abe M, Akita K, Akamatsu M (2008) Micro injection molding for mass production using LIGA mold inserts. Microsyst Technol 14:1507–1514. https://doi.org/10.1007/s00542-007-0533-8
Huang MS, Li CJ, Yu JC, Huang YM, Hsieh LC (2009) Robust parameter design of micro-injection molded gears using a LIGA-like fabricated mold insert. J Mater Process Technol 209:5690–5701. https://doi.org/10.1016/j.jmatprotec.2009.05.032
Lee BK, Kim JH (2015) Manufacturing of micromolds for plastic molding technologies via synchrotron LIGA process. J Korean Soc Manuf Process Eng 14:1–7. https://doi.org/10.14775/ksmpe.2015.14.4.001
Jiang BY, Zhou MY, Weng C, Zhang L, Lv H (2016) Fabrication of nanopillar arrays by combining electroforming and injection molding. Int J Adv Manuf Technol 86:1319–1328. https://doi.org/10.1007/s00170-015-8260-2
Funding
This work was supported by Korea Agency for Defense Development and the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (No. 2011-0030075).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gal, C.W., Han, J.S., Park, J.M. et al. Fabrication of micro piezoelectric rod array using metallic mold system for mass production. Int J Adv Manuf Technol 101, 2815–2823 (2019). https://doi.org/10.1007/s00170-018-2986-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2986-6