On the effect of plastic deformation on the coarsening of ϑ-phase precipitation in an Al-Cu alloy E. CerriE. EvangelistaN. Ryum OriginalPaper Pages: 257 - 263
An experimental and theoretical study of heat-affected zone austenite reformation in three duplex stainless steels Staffan HertzmanBengt BrolundPaulo J. Ferreira OriginalPaper Pages: 277 - 285
On the rule of additivity in phase transformation kinetics Mark LuskHerng-Jeng Jou OriginalPaper Pages: 287 - 291
Compaction and characterization of mechanically alloyed nanocrystalline titanium aluminides C. SuryanarayanaF. H. FroesG. E. Korth OriginalPaper Pages: 293 - 302
Computer simulation of multicomponent diffusion in joints of dissimilar steels Thomas HelanderJohn Ågren OriginalPaper Pages: 303 - 308
Role of matrix microstructure on room-temperature tensile properties and fiber-strength utilization of an orthorhombic ti-alloy-based composite C. J. BoehlertB. S. MajumdarD. B. Miracle OriginalPaper Pages: 309 - 323
High-temperature tensile deformation and thermal cracking of ferritic spheroidal graphite cast iron C. P. ChengT. S. LuiS. M. Chen OriginalPaper Pages: 325 - 333
Bainitic chromium-tungsten steels with 3 Pct chromium R. L. KluehP. J. MaziaszD. J. Alexander OriginalPaper Pages: 335 - 345
A critical assessment of the mechanistic aspects in HAYNES 188 during low-cycle fatigue in the range 25 °C to 1000 °C K. Bhanu Sankara RaoM. G. CastelliJohn R. Ellis OriginalPaper Pages: 347 - 361
Controlled drawing to produce desirable hardness and microstructural gradients in alloy 302 wire M. P. RiendeauM. C. MatayaD. K. Matlock OriginalPaper Pages: 363 - 375
Deformation, fracture, and mechanical properties of low-temperature-tempered martensite in SAE 43xx steels Mario SaeglitzGeorge Krauss OriginalPaper Pages: 377 - 387
Effects of test temperature, grain size, and alloy additions on the cleavage fracture stress of polycrystalline niobium A. V. SamantJ. J. Lewandowski OriginalPaper Pages: 389 - 399
A study on the subgrain superplasticity of extruded Al-Al3Ni eutectic alloy J. Y. UanL. H. ChenT. S. Lui OriginalPaper Pages: 401 - 409
Development of a pinned wall sensor using cobalt-rich, near-zero magnetostrictive amorphous alloys C. K. KimR. C. O’Handley OriginalPaper Pages: 423 - 434
A thermodynamic description for the ternary Al-Mg-Cu system S. -L. ChenY. ZuoY. A. Chang OriginalPaper Pages: 435 - 446
Effects of liquidus and solidus curvature in solidification modeling of binary systems with constant partition ratio M. RettenmayrT. Kraft OriginalPaper Pages: 447 - 451
Nucleation and phase selection in undercooled Fe-Cr-Ni melts: Part I. Theoretical analysis of nucleation behavior T. VolkmannD. M. HerlachW. Löser OriginalPaper Pages: 453 - 460
Nucleation and phase selection in undercooled Fe-Cr-Ni melts: Part II. Containerless solidification experiments T. VolkmannD. M. HerlachW. Löser OriginalPaper Pages: 461 - 469
On the precipitation of TiC in liquid iron by reactions between different phases Zhensheng LiuHasse Fredriksson OriginalPaper Pages: 471 - 483
Undulation of W/matrix interface by resintering of cyclically heat-treated W-Ni-Fe heavy alloys Heung-Sub SongJoon-Woong NohByung-Sun Chun OriginalPaper Pages: 485 - 489
Tribological properties of aluminum alloy matrix TiB2 composite prepared by in situ processing C. A. CaracostasW. A. ChiouH. S. Cheng OriginalPaper Pages: 491 - 502
Determination of the solidification curve of a RENE N4 superalloy Sinn-Wen ChenShih-Chang Jeng Communications Pages: 503 - 504
Orientation dependence of microfracture behavior in a dual-phase high-strength low-alloy steel Dongwoo SuhDongil KwonNack J. Kim Communications Pages: 504 - 509
