Skip to main content
SpringerLink
Log in

An experimental study of abrasive waterjet machining of Ti-6Al-4V

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

This paper presents an experimental study on abrasive waterjet (AWJ) machining of the most commonly used titanium alloy, Ti-6Al-4V. Two types of machining operations, i.e. drilling (or piercing) and slotting, were conducted. For the drilling experiments, the influences of water pressure and drilling time were investigated. It was found that both the hole depth and diameter increased as drilling time increased but in a decreasing rate. An increase in the water pressure increased both the hole depth and the hole diameter. For the slot cutting, the influence of water pressure and the traverse speed were investigated. A slower traverse speed resulted in a deeper depth of cut. The kerf showed a taper shape with a wider entry on top, and the width decreased as jet cut into the material. At the bottom of the kerf, a pocket was generated. The variation of the depth of cut became insignificant when the traverse speed was increased.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Chen Y, Li H, Wang J (2015) Analytical modelling of cutting forces in near-orthogonal cutting of titanium alloy Ti6Al4V. J Mech Eng Sci 229(6):1122–1133

    Article  Google Scholar 

  2. Wang J, Guo DM (2002) A predictive depth of penetration model for abrasive waterjet cutting of polymer matrix composites. J Mater Process Technol 121(2–3):390–394

    Article  Google Scholar 

  3. Axinte DA, Karpuschewski B, Kong MC, Beaucamp AT, Anwar S, Miller D, Petzel M (2014) High Energy Fluid Jet Machining (HEFJet-Mach): from scientific and technological advances to niche industrial applications. CIRP Ann Manuf Technol 63(2):751–771

    Article  Google Scholar 

  4. Finnie I (1958) The Mechanism of Erosion of Ductile Metals. Proceedings of the 3rd U.S. National Congress of Applied Mechanics, New York, USA, 527–532

  5. Bitter JGA (1963) A study of erosion phenomena part I. Wear 6(1):5–21

    Article  Google Scholar 

  6. Hashish M (1984) A modeling study of metal cutting with abrasive-waterjets. ASME Trans J Eng Mater Technol 106:88–100

    Article  Google Scholar 

  7. Li W, Wang J, Zhu H, Li H, Huang C (2013) On ultrahigh velocity micro-particle impact on steels–a single impact study. Wear 35(1–2):216–227

    Article  Google Scholar 

  8. Seo YW, Ramulu M, Kim D (2003) Machinability of titanium alloy (Ti-6Al-4V) by abrasive waterjets. Proc Inst Mech Eng B J Eng Manuf 217:1709–1721.3

    Article  Google Scholar 

  9. Fowler G, Shipway PH, Pashby IR (2004) Abrasive water-jet controlled depth milling of Ti6Al4V alloy-an investigation of the role of jet-workpiece traverse speed and abrasive grit size on the characteristics of the milled material. J Mater Process Technol 161(3):407–414

    Article  Google Scholar 

  10. Shipway P, Fowler G, Pashby IR (2005) Characteristics of the surface of a titanium alloy following milling with abrasive waterjet. 258 (1–4): 123–132

  11. Hascalik A, Caydas U, Gurun H (2007) Effect of traverse speed on abrasive waterjet machining of Ti-6Al-4V alloy. Mater Des 28:1953–1957

    Article  Google Scholar 

  12. Wang J (2007) Predictive depth of jet penetration models for abrasive waterjet cutting of alumina ceramics. Int J Mech Sci 49:306–316

    Article  Google Scholar 

  13. Hlavac ML (2009) Investigation of the abrasive waterjet trajectory curvature inside the kerf. J Mater Process Technol 209:4154–4161

    Article  Google Scholar 

  14. Orbanic H, Junkar M (2004) An experimental study of drilling small and deep blind holes with an abrasive water jet. Proc Inst Mech Eng B J Eng Manuf 218:503–508

    Article  Google Scholar 

  15. Boud F, Carpenter C, Folkes J, Shipway PH (2010) Abrasive waterjet cutting of a titanium alloy: the influence of abrasive morphology and mechanical properties on workpiece grit embedment and cut quality. J Mater Process Technol 210:2197–2205

    Article  Google Scholar 

  16. Gent M, Menendez M, Torno S, Torano J, Schenk A (2012) Experimental evaluation of the physical properties required of abrasives for optimizing waterjet cutting of ductile materials. Wear 284–285:43–51

    Article  Google Scholar 

  17. Fowler G, Pashby IR, Shipway PH (2009) The effect of particle hardness and shape when abrasive waterjet milling titanium alloy Ti6Al4V. Wear 266:613–620

    Article  Google Scholar 

  18. Anwar S, Axinte DA, Becker AA (2013) Finite element modelling of abrasive waterjet milled footprints. J Mater Process Technol 213:180–193

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Griffith School of Engineering, Griffith University, Gold Coast campus, Gold Coast, QLD, 4222, Australia

    Huaizhong Li

  2. School of Mechanical and Manufacturing Engineering, The University of New South Wales, Sydney, NSW, 2052, Australia

    Jun Wang

Authors
  1. Huaizhong Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Jun Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Huaizhong Li.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Li, H., Wang, J. An experimental study of abrasive waterjet machining of Ti-6Al-4V. Int J Adv Manuf Technol 81, 361–369 (2015). https://doi.org/10.1007/s00170-015-7245-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-015-7245-5

Keywords

Search

Navigation