Abstract
Various types of scanning can enhance the quality of welding joints, which allows us to control the energy distribution of the electron beam. In the study conducted by the authors, it was experimentally revealed that the best quality of welded joints is obtained by scanning an electron beam in the form of a sinusoidal raster. The research was conducted for thin-walled aerospace structures. Equipment was developed that realizes scanning in the form of different rasters, considering the frequency of the sweep, thereby removing the high frequency, which will allow getting a more even “saw”. As the different types of scanning shapes at which the optimization was carried out, the next types were used: a classical raster, a sinusoidal raster and a truncated raster. The obtained results allow a more meaningful approach to the process of electron beam welding of different types of materials and thin-walled structures and obtaining a consistent seam quality.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Sobko SA, Kulikov VA (2013) The method of control of electron-beam welding. Russia, Moscow
Shcherbakov AB, Rodyakina RV, Novokreschenov VV, Lastovirya VN (2018) Technology of material processing. In: Equipment of electron-beam complexes, 3rd edn. Yurayt, Moscow, pp 114–130
Akopianc KS, Nesterenko VM (2002) Electron-beam welding of steels up to 600 m thick with longitudinal oscillations of the beam. Autom Weld 9:3–5
Ohmine M, Hiramoto S, Jamane J (1993) Fundamental study on the pulsed electron beam welding. In: International Institute of Welding (D IV-348-383), 13
Belenkiy V Ya (1986) Scanning of an electron beam along an x-shaped trajectory as a means of reducing defects in the root of a weld in EBW. Autom Weld 9:35–37
Barishev MS, Redchic AA, (1990) Optimization of welding modes by oscillating electron beam. In: International conference on welding of non-ferrous metals, vol 4, p 34
Zenker R (2002) Electron beam surface treatment and multipool welding – state of the art. In: Proceedings of the EBEAM. International conference on high power electron beam technologies, vol 10, pp 12-1–12-5
Shilov GA, Akopianc KS, Kasatkin OO (1983) Influence of the frequency and diameter of the circular scan of the electron beam on the penetration in EBW. Autom Weld 8:25–28
Akopianc KS, Emchenko-Ribko AV, Neporohin VYu (1989) Prevention of the formation of root defects in EBW with non-penetration of up to 60 mm depth. Autom Weld 4:30–34
Komiro Y, Punshon CS, Gooch TG (1986) Effects of process parameters on centerline solidification in EB weld. Metal Constr 2:104–111
Vasil’ev AM, Goncharov VA, Krivkov BG (1998) Electronic beam control device by welding shipbuilding industry. Series Welding 6:11–12
Mara CL, Funk ER, McMaster, RC (1974) Penetration mechanism of electron beam welding and spiking phenomenon. Weld J 53(6):246–251
Kurashkin SO, Laptenok VD, Murygin AV (2019) Analytical characteristics of the electron beam distribution density over the heated spot for optimizing the electron-beam welding process. In: IOP conference series: materials science and engineering, vol 681, p 012021
Seregin Yu N, Laptenok VD, Uspenskiy NV (2011) Experimental research on the optimization of the technology of electron-beam welding of aluminum alloys. Technologies and equipment of EBW-2011, pp 71–80
Seregin Yu N, Laptenok VD, Murygin AV (2019) Experimental research on electron-beam welding technology with a scanning electron beam. In: IOP conference series: materials science and engineering, vol 467
Seregin Yu N, Laptenok VD, Uspenskiy NV (2014) Software of electron beam distribution energy over the heated spot by EBW. Technologies and equipment of EBW-2014, pp 39–45
Seregin Yu N, Kurashkin SO (2017) Modeling of the EBW mode for predicting the parameters of the weld. In: MPEI collection of materials of 2nd international conference, pp 26–36
Mladenov G (2009) Electronic and ionictechnologies. Prof. Marin Drinov, Sofia
Shiller Z, Gaizig U, Panzer Z (1980) Electron beam technology. Energiya, Moscow
Yazovskikh VM, Trushnikov DN, Belenky V Ya (2004) The mechanism of secondary emission processes in electron-beam welding with electron beam modulation welding. Weld Int 18:21–27
Béraud N, Vignat F, Villeneuve F, Dendievel R (2014) New trajectories in electron beam melting manufacturing to reduce curling effect. Procedia CIRP 17:738–743
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Kurashkin, S., Tynchenko, V., Seregin, Y., Murygin, A., Bocharov, A. (2022). Hardware Control of the Electron Beam Energy Density by the Heating Spot. In: Yang, XS., Sherratt, S., Dey, N., Joshi, A. (eds) Proceedings of Sixth International Congress on Information and Communication Technology. Lecture Notes in Networks and Systems, vol 235. Springer, Singapore. https://doi.org/10.1007/978-981-16-2377-6_9
Download citation
DOI: https://doi.org/10.1007/978-981-16-2377-6_9
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-16-2376-9
Online ISBN: 978-981-16-2377-6
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)