Abstract
Investigated was the spark plasma sintering (SPS) of β-SiAlON/0–30 wt % BN ceramic composites. The raw materials (β-Si5AlON7 and BN powders) were prepared by infiltration-mediated combustion synthesis (CS). Experimentally established were the following process parameters for SPS of composites with high relative density (>95%) and flexural strength of 250–300 MPa: (a) heating rate 50 deg/min, (b) maximum temperature 1650–1750°C, (c) and holding time 5 min.
Similar content being viewed by others
References
Ekström, T. and Nygren, M., SiAlON ceramics, J. Am. Ceram. Soc., 1992, vol. 75, no. 2, pp. 259–276.
Haubner, R., Wilhelm, M., Weissenbacher, R., and Lux, B., Boron nitrides: Properties, synthesis, and applications, Struct. Bonding, 2002, vol. 102, no. 1, pp. 1–45.
Shuba, R. and Chen, I.-W., Machinable a-SiAlON/BN composites, J. Am. Ceram. Soc., 2006, vol. 89, no. 7, pp. 2147–2153.
Wei, D., Meng, Q., and Jia, D., Mechanical and tribological properties of hot-pressed h-BN/Si3N4 ceramic composites, Ceram. Int., 2006, vol. 32, no. 5, pp. 549–554.
Gao, L., Jin, X., Li, J., Li, Y., and Sun, J., BN/Si3N4 nanocomposite with high strength and good machinability, Mater. Sci. Eng. A, 2006, vol. 415, nos. 1–2, pp. 145–148.
Zhao, Y.S., Yang, Y., Li, J.T., Borovinskaya, I.P., and Smirnov, K.L., Temperature factor in tailoring the morphology of Y-a-SiAlON microcrystals fabricated by combustion synthesis, Int. J. Self-Propag. High- Temp. Synth., 2009, vol. 18, no 2, pp. 87–91.
Fu, R., Chen, K.X., and Ferreira, J.M.F., Combustion synthesis of ß-SiAlON whiskers, Key Eng. Mater., 2005, vol. 280–283, pp. 1241–1244.
Niu, J., Yi, X., Nakatsugawa, I., and Akiyama, T., Saltaßsisted combustion synthesis of ß-SiAlON fine powders, Intermetallics, 2013, vol. 35, no. 1, pp. 53–59.
Munir, Z.A., Anselmi-Tamburini, U., and Ohyanagi, M., The effect of electric field and pressure on the synthesis and consolidation of materials: A review of the spark plasma sintering method, J. Mater. Sci., 2006, vol. 41, no 3, pp 763–777.
Voisin, T., Durand, L., Karnatak, N., Le Gallet, S., Thomas, M., Le Berre, Y., Castagné, J.-F., and Couret, A., Temperature control during spark plasma sintering and application to up-scaling and complex shaping, J. Mater. Process. Technol., 2013, vol. 213, no 2, pp. 269–278.
Loryan, V.E., Borovinskaya, I.P., Smirnov, K.L., and Titov, S.G., Sintering of SHS-produced a-Si3N4,a-SiAlON,and ß-SiAlON, Int. J. Self-Propag. High- Temp. Synth., 2012, vol. 21, no 1, pp. 41–44.
Smirnov, K.L. and Borovinskaya, I.P., Combustion synthesis of SiAlON-based ceramic composites, Powder Metall. Met. Ceram., 2003, vol. 42, nos. 11–12, pp. 596–602.
Yuan, B., Liu, J.-X., Zhang, G.-J., Kan, Y.-M., and Wang, P.-L., Silicon nitride/boron nitride ceramic composites fabricated by reactive pressureless sintering, Ceram. Int., 2009, vol. 35, no 6, pp. 2155–2159.
Zhang, G.-J., Yang, J.-F., Ando, M., and Ohji, T., SiAlON–boron nitride porous composites: In situ synthesis, microstructure, and properties, Key Eng. Mater., 2003, vol. 237, pp. 123–128.
Author information
Authors and Affiliations
Corresponding author
About this article
Cite this article
Nefedova, E.V., Grigoryev, E.G., Fokin, D.A. et al. Spark plasma sintering of β-SiAlON–BN composites from combustion-synthesized powders. Int. J Self-Propag. High-Temp. Synth. 25, 229–233 (2016). https://doi.org/10.3103/S1061386216040075
Received:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1061386216040075