Abstract
Background
The extraction of lipids from microalgae requires a pretreatment process to break the cell wall and subsequent extraction processes to obtain the lipids for biofuels production. The multistep operation tends to incur high costs and are energy intensive due to longer process operations. This research work applies the combination of radicals from hydrogen peroxide with an organic solvent as a chemical pretreatment method for disrupting the cell wall of microalgae and simultaneously extracting lipids from the biomass in a one-step biphasic solution.
Result
Several parameters which can affect the biphasic system were analyzed: contact time, volume of solvent, volume ratio, type of organic solvent, biomass amount and concentration of solvents, to extract the highest amount of lipids from microalgae. The results were optimized and up to 83.5% of lipid recovery yield and 94.6% of enhancement was successfully achieved. The results obtain from GC-FID were similar to the analysis of triglyceride lipid standard.
Conclusion
The profound hybrid biphasic system shows great potential to radically disrupt the cell wall of microalgae and instantaneously extract lipids in a single-step approach. The lipids extracted were tested to for its comparability to biodiesel performance.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
Microalgae consists of high lipid content and is very potential as a sustainable feedstock for commercial biofuel production. The lipid content in microalgae constitutes of more than 50% of the total composition in the biomass [1, 2]. They are listed as a third-generation of biomass which can convert carbon dioxide into lipids and biofuels through transesterification. The productivity of microalgae oil in liters per hectare of land is higher compared to palm oil and sunflower oil by more than 16-fold [3, 4]. Furthermore, microalgae can grow in abundance and emerge as a potential source for lipid extraction for biofuel generation to replace petroleum fuel [5]. Lipids are a class of organic compounds which comprises of fatty acids and glycerol in its natural form, commonly known as triglyceride. The microalgae cell contains various types of lipid, however, the lipid favored for biofuel production are neutral lipids. Phospholipids and glycolipids are polar lipids which belongs to the category of structural lipids mainly used for construction of cell wall membranes, such as being integrated with fiber and polysaccharide in the raw molecular compound in the cell wall membrane [6]. The extraction technique for lipid extraction commonly involves the use of organic solvents to dissolve lipids and further purification of the lipid content by evaporating the solvents [7]. The lipids from microalgae could be processed to produce cosmetic products, biofuel, nutraceuticals, and synthetic polymer [2, 8,9,10].
The conventional solvent extraction techniques using alcohol and organic solvents by Folch method or Bligh and Dyer method is a common practice for lipid extraction in a laboratory scale [11, 12]. The alcohol solvent is prone to attracting polar compounds as it contains hydroxyl group molecules (OH), while organic solvent is categorized as non-polar solvent which can dissolve lipids in the solution. The molecular structure of every alcohol contains similar carbon chain with non-polar characteristic due to the carbon and hydrogen both consisting of low electronegativity difference, and OH group with polar properties attached at the tail of the chains [13, 14]. Thus, alcohol has been categorized as a polar group of solvent due to the presence of hydroxyl functional group in the chains. Typical solvent extraction uses different type of solvents in the immiscible phase, where the distribution of ions and particle may occur according to the compatibility of the types of solvent to attract or release ions in the solution [15]. The conventional alcohol and organic solvent extraction does not create a significant cell disruption mechanism for the microalgae biomass. Pre-treatment processes such as mechanical or chemical method are needed to induce the cell wall membrane disruption before the lipid compounds may be released and readily dissolve into the organic solvent [16].
Current technologies used for mechanical pre-treatments in microalgae cell disruption includes bead milling, high-pressure homogenization, ultrasonication, microwave, pulse electric field, cavitation and thermal disruption methods [17]. These cell disruption techniques are reviewed intensively for the industrial algae biorefinery processing. The efficiency of mechanical cell disruption methods is based on energy input and duration of the process, where most of these techniques are highly energy intensive and require costly equipment [18, 19]. On the other hand, cell wall could be disrupted by chemical treatments such as acids, bases, and surfactants [20]. Chemical treatments are often associated with concerns on contamination and product quality compromise which is observed for food products extraction such as protein, antioxidant, and others nutrient supplements. The use of chemical treatments provides greater contact surface for liquid cell disruption compared to mechanical methods as the mechanical pretreatments rely on the contact orientation and is mobility restraint. The introduction of peroxyl cell disruption as a chemical treatment layer for enhancing extractability of microalgae lipids can be considered through the possibility of radical formation including peroxidation for the lipids. The biofuel production performance from biomass has also been reported to improve through applying radical cell disruption methods [21].
The oxygen–oxygen bond homolyzes in hydrogen peroxide (HOOH) forming a radical pair, in which the separation of the two hydroxyl radicals (OH) are in symmetry and there are more than 10 kJ/mol of energy needed. The difference of heterolysis and homolyzes of the dissociation components from the molecules are between ions and radicals. Heterolysis is a process of cleaving or loosening of electrons from the original bonded pair of the elements to form ions charge in the solution [22]. The transfer of ion occurs by breaking itself from a neutral molecule and subsequently made into a form of cation and anion from their parent compounds. Homolyzes is a process where the mechanism of radical forming in which the chemical bond dissociates from a molecule and form radical pairs [21, 23]. Each of the fragments obtain equal quantity of the original bonded electron. There is a possibility that applying heat or light source such as UV-ray to the bonds from the solution can trigger the homolytic and heterolytic cleavage process and generate radicals and ions [24].
In this work, a single-step extractive method with radical cell disruption properties for lipids extraction purpose was performed. This hybrid method involves the cell disruption of microalgae using a chemical base liquid mixture with an organic solvent for dissolving the lipids. The mixture of two types of liquids will form a biphasic system and the organic phase containing the lipid was characterized for the lipid concentration. Process parameters such as the concentration of the hydrogen peroxide, type of organic solvent, concentration of the organic solvent, ratio alternation, biomass variation, and volume of solvent, was optimized throughout the experiment to obtain the maximum recovery of lipid from microalgae biomass.
Materials and methods
Materials
Hydrogen peroxide (H2O2), hexane (C6H14), chloroform (CHCl3), acetone (C3H6O), methanol (CH3OH), and sodium chloride (NaCl) were purchased from R&M chemicals (Malaysia). Triglyceride lipids standard mixture were purchased from Sigma Aldrich (USA). All chemicals and solvents used were of analytical grade.
Microalgae biomass cultivation
Chlorella sorokiniana CY-1 strain has been selected in this study due to its high lipid content and the strain was provided by the National Cheng Kung University, Taiwan. C. sorokiniana CY-1 was cultivated in a laboratory scale vertical photobioreactor (PBR) as [25] using BG-11 medium containing (g/L): NaNO3, 1.5; K2HPO4, 0.03; MgSO4·7H2O, 0.075; citric acid, 0.006; Na2CO3, 2.0; CaCl2·2H2O, 3.6; Ferric ammonium nitrate, 0.6, EDTA, 0.1; H3BO3, 2.86; MnCl2·4H2O, 1.81; ZnSO4·7H2O, 0.222; Na2MoO4·2H2O, 0.39; CuSO4·5H2O, 0.079; Co(NO3)·6H2O, 0.049. The pre-culture and batch culture were both conducted in an indoor PBR system consisting of a 1 L glass vessel. The PBR was aerated with compressed air and an additional 5% of CO2 from a tank. The aerated air is filtered through a 0.45 μm air filter before entering the PBR. The photobioreactor was illuminated by external LED light sources with a light intensity of 200 μmol/m2/s on both sides of the vessel. The light intensity was determined by using LI-190SA pyranometer sensor (LI-COR, Lincoln USA). The operating temperature was in room condition around 25–27 °C with agitation speed of 300 rpm. Adequate biomass content was cultivated for the whole experiment.
Determination of nitrate content and microalgae cell concentration
Nitrate content and microalgae cell concentration was measured by spectrophotometric method as mentioned in a previous research [26]. For nitrate content, the supernatant fluid after centrifugation of the microalgae samples was obtained and diluted with deionized water. The nitrate content was measured at optical density of 220 nm using UV–Vis spectrophotometer (UV-1800, Shimadzu). While for microalgae cell concentration, the microalgae samples were measured directly at an optical density 680 nm. Harvesting of microalgae was conducted when the biomass and nitrate level reached a constant value. The approximation of harvesting period was around 14–16 days, where the microalgae culture broth harvested was centrifuged at 7000 rpm for 5 min. The microalgae biomass was freeze dried for 24 h and the resulting microalgae powder was used for experimental extraction studies.
Hybrid liquid biphasic system with radical cell disruption properties
The hybrid liquid biphasic system (HLBS) was generated by initially adding functionalized hydrogen peroxide (functionalized by exposing hydrogen peroxide to the florescent lamp at intensity of 8 µmol/m2/s for initiating the radical propagation) to 20 mg of biomass, followed by the addition of organic solvent for dissolving lipid in a 1:1 volume ratio of mixture. The solution was vortexed for 10 s and left for 1 min to allow the contact of the liquid mixture. Two phases were formed where the upper phase was hexane and lower phase was hydrogen peroxide disruption solvent. The organic solvent phase was separated using a pipette and analyzed for lipids concentration. Lipid triglyceride concentration was optimized at every parameter by utilizing the UV–Vis spectrometer at range of 220 nm–290 nm, in which the exact value for lipid content in hexane and chloroform are at 239 and 223.5 nm, respectively [27,28,29]. The final optimized lipid was tested through Perkin Elmer GC-FID. The column used was Perkin Elmer Elite-5 (30 m × 0.32 mm × id 0.25 μm) with helium 1.0 mL/min, column oven temperature held at 35 °C for 3 min, increasing to 200 °C with increment of 20 °C/min. The split ratio was 15:1. The concentration of organic solvent (20%) was prepared by diluting with acetone to form a homogeneous phase of solvent. Acetone is stable with oxidant solvent and mixes well with chloroform and hexane (ECHA 2019).
Total lipid analysis
Total lipid content in the microalgae biomass was determined using the following methods [12, 30]. Approximately 20 mg (± 0.3 mg) of microalgae biomass powder was filled into a 10 mL centrifuge tube. 3 mL of the solvent mixture, chloroform:methanol (2:1, v/v) was added. The contact duration for microalgae biomass in the solution was set at 30 min to allow the biomass to settle down and particulate in the solution. The supernatant lipid mixture was extracted using micropipette and transfered to a separate tube. The solution was heated at 60 °C for 1 h, then washed with 0.9% NaCl solution by 20% volume of the solution mixture. After vortexed, the mixture and the solution will form two phases, where the upper phase will be siphoned out and the lower phase containing lipids was dried by evaporation in a fume hood at room temperature condition for 3 h [31, 32]. The total weight of lipid extract remaining after evaporation was measured (Table 1).
Determination of recovery yield and enhancement value
The recovery yield (R, %) of lipids from the total lipid content was represented by Eq. 1 below:
The comparison percentage of using organic solvent biphasic compared to using water (without cell disruption solvent) is known as the enhancement value (E, Eq. 2). For the non-disruptive solvent extraction, the microalgae biomass was dissolved in distilled water in room temperature followed by the addition of organic solvent. The contact time duration was set as 1 min.
where Ai stands for optimized concentration of lipids, and Href stands for H2O with organic solvent (biphasic system without cell disruption properties). The results were analyzed for three repetitive individual samples.
Chemical reaction chains of radical formation
The potential of using radicals generated by the Fenton reaction to promote cell disruption for microalgae was experimentally tested [21]. Hydrogen peroxide was used without introducing Ferric ion to initiate the radical in the presence of conventional room fluorescent lamp condition. The reaction ID R3–R4 is the lumped reaction with rate constant kd and kLp respectively, as shown in Table 2.
In Table 2, the model parameters for estimating OH* radical concentration were shown. The lipid yield coefficient YL/X (mglip/mgbiomass) mentioned in [33] was used to anticipate the capability of oxidizing organic compounds in the solution, while the yield coefficient YOH/X depicts the amount of OH* radical needed for rupturing cell wall of microalgae. kd is the rate constant for Eq. (3) and kLp is the rate constant for Eq. (4).
The OH* radical produced by hydrogen peroxide may react with several compounds released from microalgae. Thus, the cell wall may cause degradation and consequent disruption on the protective cell layer. These reactions are known as a lumped reaction scheme to describe the overall disruption process [21]. The key radical formation steps as reported in Table 3.
Cell disrupted scheme
where YOH/X is the OH* needed to disrupt 1 mol of biomass, YL/X is the coefficient for amount (mol) of lipid released when 1 mol of biomass cell has been disrupted (amount of lipid peroxidation), DX is the disrupted cell, LH is the unsaturated lipid, X is the microalgae cells (biomass).
The radical reaction chain and peroxidation of lipid molecules were performed according to the initial, propagation and termination steps. The rate constants for the reaction steps are found in Table 3 and the reaction chain was described for the key reactions in the cell disruption from the interaction of radical species and lipid molecules.
Initiation (Homolytic Reaction)
Propagation
Termination
The hydroxyl radical OH* is highly reactive of free radical with short life span, therefore, the steady state of the concentration value for hydroxyl radical could be ignored. The concentration of the OH radical could be integrated through Eq. (12). Besides, the initial formation of hydroxyl could be described from Eq. (13) for the evolution of time and the effect of concentration of OH radical from the UV radiation from florescent lamp in normal room condition with intensity 8 μmol/m2/s.
The formation of hydroxyl radical could be estimated from differentiating equation from Eq. (14) through ordinary differential equation (ODE) from Matlab 2018a to express the radical formation time taken and concentration. Initial condition [x] = 0.8229 mol/L (experimental value for 20 mg of biomass for conversion), [\({\text{H}}_{2} {\text{O}}_{2} ]\) = 0.03837 mol/L, [LH] = 0.03837 mol/L (assumption value for every H2O2 reacted with lipid and formed lipid hydroxide).
Result and discussion
Effect of concentration of hydrogen peroxide toward lipid extraction
The concentration of hydrogen peroxide in the hybrid liquid biphasic system (HLBS) will directly affect the yield of lipids. Formation of hydroxyl or peroxyl is through homolytic reaction, where the bond breaking from the molecules creates abnormal valency that causes the radicals to seek electrons to substitute the valency [37]. The radical molecules may attract the electron from the cell wall surface of the microalgae biomass to form new bonds out of the cellular wall. The rapid radical formation through Fenton reaction is potential in causing disruption to the cell wall membrane of microalgae which leads to the release of nutrient compounds including lipids, making these compounds dissolve in the organic solvent phase [21]. The current method is suitable for extracting compounds in industrial applications and will not pose concerns of the radical degrading the extracted compound and causing peroxidation for lipid. This will avoid the lipid peroxidation chain reactions that leads to the formation of highly reactive electrophilic aldehydes, and hinder its negative effect for human internal organs [38, 39]. The radical formation is supported by florescent UV in open space condition with intensity of 8 μmol/m2/s without any external equipment for further enhancing the homolytic reaction.
Figure 1 shows the effect of hydrogen peroxide concentration on the lipid recovery yield and enhancement of the process. The highest recovery of lipid was observed at 30% concentration of hydrogen peroxide solution which yielded 50.9% lipid. The results show an increasing trend from the lowest hydrogen peroxide concentration, from 5 up to 30%. The maximum purity of hydrogen peroxide used in this work was limited to 30%, while for the purity of hydrogen peroxide, values higher than 30% would result in a highly oxidizing agent with strong oxidative properties that is usually used in the aerospace propulsive system as a hypergolic propellant thruster, also known as propulsion grade of reagent [40]. Therefore, the maximum concentration of the hydrogen peroxide does not exceed 30% in this experiment. Hydrogen peroxide is a polar solvent that attracts polar compound, while organic solvent tends to dissolve neutral or non-polar lipids [41]. Polar lipid consisting of glycolipid and phospholipid as the major components will affect the biofuel properties and conversion rate [42].
Concentration of peroxide with hexane effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 3 mL of 85% concentration of organic solvent (hexane), contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
Chloroform compared with hexane as the organic solvent, have a higher density at 1.49 g/cm3 compared to the density of hexane (0.65 g/cm3) and hydrogen peroxide (1.45 g/cm3). Thus, chloroform will settle to the bottom of the solution along with the biomass. Additional steps such as centrifugation were needed to fully separate the biomass and the organic solvent. Moreover, chloroform will not clearly separate the polar lipid into the surface of the solution, where it dissolves both polar lipid and non-polar lipid into the solvent. The HCl molecules may also convert the chloroform into carbon dioxide which is unwanted. Figure 2 shows the lipid recovery and enhancement using chloroform as an organic solvent with varying concentration of radical solvent for lipid extraction. The highest enhancement (99.7%) and recovery yield (61.7%) for lipid was found at 15% H2O2 in chloroform. Comparing similar concentrations at 30%, the use of chloroform combination showed about 5% higher in recovery yield compared to the hexane combination.
Concentration of peroxide with chloroform effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 3 mL of 85% concentration of organic solvent (chloroform), contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
The hydrogen peroxide concentration in chloroform at 5% have the lowest recovery yield of 46.65% and enhancement of 99.63%, while the highest lipid recovery yield and enhancement was 61.8% and 99.7%, respectively at 15% concentration of hydrogen peroxide in chloroform. The overall chloroform mixture results for recovery yield is higher than hexane as chloroform dissolves both polar and non-polar lipids in the solvent, where it will add salt solution in the solvent for washing and purification purposes [30]. The suitable type of lipid-based biofuel conversion utilizes neutral lipid which can perform better during the conversion into biofuel. Chloroform is tautomeric in-equilibrium where there is common relocation of the proton in the molecules. During light beam lighting on electrons, the tautomeric effect causes absence of energy returning electrons back to the ground state, therefore creating no energy dissipation and causing unstable measurements in the UV–Vis reading for chloroform [43]. Due to the characteristic of chloroform which dissolves both the polar and non-polar lipids, these lipids are not favorable to be used as biofuels because polar lipid from phosphorous and glycolipid affects the combustion and causes environmental issues. Furthermore, the tautomeric and aprotic effect does not contribute to better stability of the biofuel and may disturb the spectroscopic analysis performance. Therefore, hexane was selected as the better solvent of the two for lipid extraction.
Effect of solvent concentrations
Organic solvents play a vital role for lipid extraction due to its capability of dissolving lipids. The concentration for organic solvents in the HLBS has been altered to observe the effect towards recovery yield and enhancement. The concentration of organic solvent was investigated in the range of 20–85%. From Fig. 3, the optimum concentration for hexane is 60% for R and E value which is 43.2% and 97.42% respectively. The dilution of hexane is done with acetone which is nonreactive, non-metabolized, low viscosity and able to mixed well with most organic solvents [44]. The least recovered yield of lipid (19.17%) is at 20% concentration of hexane. The highest purity 85% of hexane showed reduced recovery yield at 30.2% and the enhancement at 96.3% compare to 60% concentration of hexane dilution with 40% of acetone. The highest recovery yield and enhancement for hexane dilution is at 60% where 97.4% of enhancement and 43.2% of recovery yield was achieved. Acetone can dissolve in polar and non-polar solvents, it consists of non-polar methyl groups and polar carbonyl (C=O) groups that allows it to dissolve in most polar and non-polar solvent types. Acetone is also an aprotic solvent with polar features and is prone to attract polar compound such as phospholipid and glycolipid [45]. Hence, acetone was selected as the suitable choice for its capability to dissolve in most types of non-polar solvent including chloroform and hexane without forming two different phases.
Concentration of organic solvent (hexane) effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 3 mL of 30% concentration of hydrogen peroxide, contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
The concentration varying for chloroform for extracting lipid was shown in Fig. 4, the optimum concentration for chloroform is at 60% and the enhancement is at 99.8% while recovery yield is 81.5%. The pure chloroform shown 99.8% enhancement and 55.7% recovery yield which is significantly lower for by 25.8% compare to 60% concentration of chloroform, this indicates that too high chloroform concentration will greatly reduce the lipid recovery yield. The optimum result for dilution of organic solvent for lipid extraction was selected to be 60% dilution of chloroform solvent with 40% of acetone.
Concentration of organic solvent (chloroform) effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 3 mL of 30% concentration of hydrogen peroxide, contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
Comparing with hexane dilution parameter, both the enhancement and recovery yield of using chloroform are higher. However, chloroform and acetone dilution for optimizing the lipid content is unstable due to the aprotic and tautomeric effect. According to the eluotropic series, taking silica as stationary medium indicates that hexane is a non-polar solvent with low detecting value in UV–Vis compared to chloroform [46, 47]. This means that the minimum detecting value for hexane is lower compared to most organic solvents including chloroform, acetone and toluene. Moreover, hexane is a favorable choice for solvent as it has higher stability and is more accurate for the parameter determination. It is reported that there are more monounsaturated fatty acids than polyunsaturated fatty acids in extraction processes using hexane derived solvents [48]. The monounsaturated fatty acids are preferred as the quality components for biodiesel properties in terms of low temperature fluidity and oxidative stability [49]. Therefore, hexane of 60% is been selected as the choice of organic solvent with 43.2% of lipid recovered yield.
Effect of different ratio (H2O2:Hexane)
Due to tautomeric effect and aprotic solvent distraction, pure hexane is chosen for optimizing this parameter for enhancing the lipid extraction for HLBS system. In Fig. 5, cell disruption and organic solvent extraction ratio in the system was altered for the lipid productivity of microalgae biomass. In the HLBS, the bottom aqueous layer consists of solvents for cell disruption of the biomass and the top organic layer contains hexane for dissolving lipids. The ratio for both solvents was studied to evaluate the effect of alternating the ratio of the solutions on the enhancement and recovery rate. The optimum ratio for lipid extraction is 1:3 where the E and R value are at 95.3% and 49.3% respectively. By increasing the cell disruption phase, the recovery yield does not increase proportionally, as the recovery yield for ratio 1:1, 2:1 and 3:1 showed 37.8%, 27.4% and 35.3%, respectively. Whereas by adjusting the ratio for cell disruption and organic phase will lead to a significant increase in recovery by about 3.5-fold when compared between the ratio 1:2 and 1:3. For a constant H2O2 amount, adding more organic solvent will assist in dissolving more lipids from the biomass.
Ratio of (H2O2: Hexane) effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 30% concentration of hydrogen peroxide, pure analytical grade of organic solvent (hexane), contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
H2O2 ratio in the default time of contact of 1 min accumulated more lipid from the biomass compared to 1:2 (H2O2:Hexane). This may be due to more peroxyl and hydroxyl radicals from the H2O2 assisting in the cell disruption once the H2O2 ratio has increased. The introduction of H2O2 assures the presence of peroxyl and hydroxyl radicals in the solvent to cause disruption of the cell membrane and thus allowing lipid molecules to dissolve into the organic solvent. The contact time represents the cycle of radical propagation frequency of the biomass in HLBS system, which plays a major role for preventing further disruption of the lipid compounds [50]. This parameter evaluation has indicated that the higher organic solvent with a same disruptive solvent amount will result in higher recovery of lipids as there will be more available volume for the lipids to dissolve into the system.
Effect of volume differences
The difference in volume for the H2O2 cell disruption layer was studied and its effect on the lipid recovery yield and enhancement is shown in Fig. 6. The highest extracted lipid is with 3 ml of volume, obtaining 94.6% enhancement and 57.5% of recovery yield of lipid. The addition of more hydrogen peroxide volume into the HLBS system may tend to induce more hydroxyl and peroxyl radicals which should increase the cell disruption rate [51], however, the results shows an inconsistent trend. Too much radicals may have cause the disruption of the lipids which result in lower recovery, hence it is not advantageous to add a higher amount of cell disruptive solvent. The least recovery and enhancement is in 2 ml of hydrogen peroxide, which is at 28.37% and 89.1% respectively. The decreasing cell disruption layer phase volume in general does not contribute to a significant recovery yield of lipid. This is due to the cell membrane properties which needs more radical propagation cycles to disrupt the cell membrane of microalgae. The optimum volume amount is 3 ml as it achieved the highest yield in this experimental parameter.
Volume of hydrogen peroxide (H2O2) effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 30% concentration of hydrogen peroxide, pure analytical grade of organic solvent 85% (hexane) at volume 3 mL, contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
The volume difference of organic solvent in the HLBS system was also studied and the results of lipid recovery and enhancement are shown in Fig. 7. The highest extracted lipid amount is at 3 ml of hexane and 1 ml of hydrogen peroxide in the HLBS system, achieving an enhancement of 90.2% and recovery yield of 56.7%. A decreasing trend was observed by adding more volume of organic solvent (hexane) into the HLBS system. Hexane has a delta value of 14.9 δ for total and partial solubility value after propane in the non-polar fluids categories, indicating the solubility value for oil and lipid [52]. Thus, by adding more solvents of the same solubility into the HLBS system will not enhance the extraction capability but may dilute the solution for analysis of lipid compound. The enhancement in Fig. 7 shows a decrement by more than 10% as more hexane were added in the system. The optimum volume for HLBS is 3 mL in this experimental parameter.
Volume of organic solvent (hexane) effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 30% concentration of hydrogen peroxide at volume 3 mL, pure analytical grade of organic solvent 85% (hexane), contact time at 1 min, biomass 20 mg (± 1 mg), and at room temperature 25 °C
Effect of contact time
The concentration of hydrogen peroxide and hydroxyl radical formation against time was simulated by using the mathematical modelling, where the time of hydroxyl radical formation was completed within 0.35 s. The estimated concentration was at 0.035 mol/L for the hydroxyl radical (Fig. 8). The optimized time may enhance the lipid extraction into the organic solvent. This parameter may affect the degradation rate of the cell membrane with the initial reasoning that longer contact time of the cell disruption phase layer could improve the productivity of lipid extraction. The highest lipid recovery yield and enhancement is with 3 min contact time at 83.5% and 94.4% respectively (Fig. 9). The least enhancement and recover yield are found within 1 min of contact time at 88.9% and 41.7% respectively. According to the study by Concas et al. the peak value of time contact exceeding 3 min will reduce lipid production and our results are in accordance with their work [21]. The recovery yield and enhancement of lipid extraction reached the peak at 3 min and started fall at 4 min. The time of contact may increase the cell disruption and lipid will be released more efficiently in the organic solvent, resulting in more lipids accumulation in the solvent. Prolonged contact time will eventually caused the disrupiton of lipids that leads to lower lipids production. The radical cell disruption method has also been reported to enhance the quality of biodiesel, as the characteristic of biodiesel produced with radical disruption method are more stable with reduction of undesired polyunsaturated fatty acid, such as linolenic acids (C18:3), from the lipid molecular structure [53]. Furthermore, the lipids produced may be used as industrial intermediate products for polymer crosslinking products, since the lipid compounds extracted have been radically treated and retain a partially functionalized form of the unsaturated chains from the hydrocarbon molecules [54]. The contact time of 3 min showed the best R and E and hence it was selected as the optimum value for this experimental parameter.
Time of contact effect for the extract lipid productivity for recovery yield and enhancement comparison toward water-organic solvent biphasic system from C. Sorokiniana CY-1. Other operating condition fix at 30% concentration of hydrogen peroxide, pure analytical grade of organic solvent 85% (hexane), biomass 20 mg (± 3 mg), and at room temperature 25 °C
Effect of biomass amount with solvent ratio and GC-FID lipid profile
The retention time for the lipid profile comparison in Table 4 has shown that the percentage error for peak 1, 2, 3, and 4 are less than 1%. The similarity of the lipid profile through GC-FID results for these 4 peak components in Table 4 is apparent and observed with the lipid extraction in the optimized HLBS solution mixture. The results from GC-FID indicates that the lipids extracted are comparable to that of commercial triglyceride and the HLBS process used is very potential in recovering the lipids efficiently. In chromatography, the detect signal for the analyte is directly proportional to the concentration of the component in the solution against functional of time [55]. These components of fatty acids are the potential tail which are attached to the glycerol to form triglycerides in lipids.
The effect of biomass amount correlates with the ratio of solvent in HLBS for improving the lipid productivity. Increase in biomass amount will increase the lipid output from the final extraction process, but it will not directly improve the lipid recovery yield and enhancement value (Table 5). The optimum ratio for 20 mg of biomass was found at 1:3 (H2O2:Hexane solvent ratio), where the values E and R achieved 93.8% and 37.4% respectively. In 30 mg of biomass, the 2:3 solvent ratio is best where the E and R values achieved 93.1% and 33.6% respectively. The value for 40 mg of biomass achieved higher productivity at 2:3 ratio, where the recovery is 53.9% and enhancement is 95.7%. While for 50 mg of biomass, 2:3 was the optimum ratio for extraction as the R and E values reported were the highest. The addition of more biomass does not assist in lipid recovery, but it demonstrates a relationship between varying biomass weight with ratio which will affect the lipid recovery and enhancement value. This is due to more contact surface area for cell disruption when more biomass is added within the same amount of solvent. Ratio of 1:3 showed higher lipid recovery yield at 54.6% with 50 mg of biomass and enhancement value of 95.8%. Besides, for ratio 2:3 the highest lipid recovery and enhancement is at 55.1% and 95.8%, respectively, which showed improvements of 1.2% for R and 0.09% for E value compare to 40 mg with the same ratio. The ratio for 3:3 have the highest E and R value at 50 mg which are 94.9% and 45.4% respectively, while the value is higher than 3:4 ratio with the same amount of biomass at 50 mg with an increment of 1.26% in E and 9% in R value. Ratio 2:3 (H2O2:Hexane) is the most versatile ratio to various biomass amount in this experimental parameter. It is deduced that a suitable ratio of the solvents will assist in optimizing the extraction through reducing chemical solvent consumption as well as lowering the material costs needed.
Conclusions
The hybrid liquid biphasic system (HLBS) in a single solution with two different phases in the system is efficient for the extraction of lipids from microalgae. The combination of cell disruption pre-treatment along with simultaneous extraction process will contribute to cost and energy saving by reducing the multistep procedure to a single-step extraction technique. Furthermore, this HLBS method could be applied in producing biofuels with enhanced properties through treatment in the hybrid system. Both the extraction and cell disruption will occur in two immiscible phases for ease of separation which is sustainable as there is potential to recycle of the solvents in large scale applications. More than 80% of lipids were successfully recovered from microalgae biomass and the extraction enhancement compare to water biphasic system achieved was higher than 90%. This hybrid biphasic system is potential to be applied in lipids extraction involving biomass with thick cell wall, especially for commercial biofuel production which requires biofuels of enhanced quality performance.
Availability of data and materials
Not applicable.
References
Chew KW, Yap JY, Show PL, Suan NH, Juan JC, Ling TC, Lee D-J, Chang J-S. Microalgae biorefinery: high value products perspectives. Bioresour Technol. 2017;229:53–62.
Chia SR, Ong HC, Chew KW, Show PL, Phang S-M, Ling TC, Nagarajan D, Lee D-J, Chang J-S. Sustainable approaches for algae utilisation in bioenergy production. Renew Energy. 2018;129:838–52.
PaulAbishek M, Patel J, PremRajan A. Algae oil: a sustainable renewable fuel of future. Biotechnol Res Int. 2014;2014:272814.
Subramanian S, Barry AN, Pieris S, Sayre RT. Comparative energetics and kinetics of autotrophic lipid and starch metabolism in chlorophytic microalgae: implications for biomass and biofuel production. Biotechnol Biofuels. 2013;6:150.
Hossain N, Mahlia T, Saidur R. Latest development in microalgae-biofuel production with nano-additives. Biotechnol Biofuels. 2019;12:125.
Borowitzka MA, Moheimani NR. Algae for biofuels and energy. New York: Springer; 2013. p. 77–89.
Tester CC, Joester D. Chapter twelve—precipitation in liposomes as a model for intracellular biomineralization. In: De Yoreo JJ, editor. Methods in enzymology. New York: Academic Press; 2013. p. 257–76.
Ariede MB, Candido TM, Jacome ALM, Velasco MVR, De Carvalho JCM, Baby AR. Cosmetic attributes of algae—a review. Algal Res. 2017;25:483–7.
Demirbas A, Fatih Demirbas M. Importance of algae oil as a source of biodiesel. Energy Conv Manag. 2011;52:163–70.
Stefan Mecking PK. Production of synthetic polymer from algae oil. Germany: Bioprod Baden-Wurttemberg GmbH. 2014. https://www.biooekonomie-bw.de/en/articles/news/production-of-synthetic-polymers-from-algae-oil/. Accessed 24 Apr 2019.
Bligh EG, Dyer WJ. A rapid method of total lipid extraction and purification. Can J Biochem Phys. 1959;37:911–7.
Folch J, Lees M, Sloane Stanley GA. simple method for the isolation and purification of total lipides from animal tissues. J Biol Chem. 1957;226:497–509.
Lawrence C. Chapter 10—fibre to yarn: filament yarn spinning. In: Sinclair R, editor. Textiles and fashion. Woodhead: Woodhead Publishing; 2015. p. 652–894.
Rerek ME. 27—ProLipid® Skin-mimetic lamellar gel carrier and delivery systems. In: Rosen MR, editor. Delivery system handbook for personal care and cosmetic products. Norwich: William Andrew Publishing; 2005. p. 285–302.
Vovers J, Smith KH, Stevens GW. Chapter 4-Bio-based molecular solvents. In: Pena-Pereira F, Tobiszewski M, editors. The application of green solvents in separation processes. New York: Elsevier; 2017. p. 320–560.
Patel A, Mikes F, Matsakas L. An overview of current pretreatment methods used to improve lipid extraction from oleaginous micro-organisms. Molecule (Basel, Switzerland). 2018;23:1562.
Dhondt E, Martín-Juárez J, Bolado S, Kasperoviciene J, Koreiviene J, Sulcius S, Elst K, Bastiaens L. 6-Cell disruption technologies. In: Gonzalez-Fernandez C, Muñoz R, editors. Microalgae-based biofuels and bioproducts. Woodhead: Woodhead Publishing; 2017. p. 320–560.
Munir N, Sharif N, Shagufta N, Saleem F, Manzoor F. Harvesting and processing of microalgae biomass fractions for biodiesel production (a review). Sci Tech Dev. 2013;32:235–43.
Show K-Y, Lee D-J, Tay J-H, Lee T-M, Chang J-S. Microalgal drying and cell disruption–recent advances. Bioresour Technol. 2015;184:258–66.
Hayes M, Skomedal H, Skjånes K, Mazur-Marzec H, Toruńska-Sitarz A, Catala M, IsletenHosoglu M, García-Vaquero M. 15-Microalgal proteins for feed, food and health. In: Gonzalez-Fernandez C, Muñoz R, editors. Microalgae-based biofuels and bioproducts. Woodhead: Woodhead Publishing; 2017. p. 250–352.
Concas A, Pisua M, Caoa G. Microalgal cell disruption through Fenton reaction: experiments, modeling and remarks on its effect on the extracted lipids composition. Chem Eng. 2015;43:367.
Nic M, Jirat J, Kosata B. Compendium of chemical terminology gold book. IUPAC compendation of chemistry terminology. 2014. p. 1132.
Lymar SV, Khairutdinov RF, Hurst JK. Hydroxyl radical formation by O–O bond homolysis in peroxynitrous acid. Inorg Chem. 2003;42:5259–66.
Liu W, Ma D, Guo H, Gu G. UV-induced catalyst-free intramolecular formal Heck reaction. J Saudi Chem Soc. 2018;140:16929.
Chen C-Y, Yeh K-L, Chang H-Y, Chang J-S. Strategies to improve oil/lipid production of microalgae in outdoor cultivation using vertical tubular-type photobioreactors. Energy Proced. 2014;61:2755–8.
Chew KW, Chia SR, Show PL, Ling TC, Arya SS, Chang J-S. Food waste compost as an organic nutrient source for the cultivation of Chlorella vulgaris. Bioresour Technol. 2018;267:356–62.
Mitra S. Protective role of native bovine serum albumin and alpha-unsaturated fatty acids on catechin oxidation. Indian J Chem B. 2012;51(8):1131–44.
Dzomba P, Togarepi E, Musekiwa C, Chagwiza C. Improving oxidative stability of soya and sunflower oil using Temnocalyx obovatus extracts. Afr J Biotechnol. 2012;11:11099–103.
Gomez NA, Abonia R, Cadavid H, Vargas IH. Chemical and spectroscopic characterization of a vegetable oil used as dielectric coolant in distribution transformers. J Braz Chem Soc. 2011;22:2292–303.
Gosch BJ, Magnusson M, Paul NA, De Nys R. Total lipid and fatty acid composition of seaweeds for the selection of species for oil-based biofuel and bioproducts. GCB Bioenergy. 2012;4:919–30.
Carpio RB, De Leon RL, Martinez-Goss MR. Growth, lipid content, and lipid profile of the green Alga, Chlorella vulgaris Beij, under different concentrations of Fe and CO2. J Eng Sci Technol. 2015;6:19–30.
Fry R. Systems biology in toxicology and environmental health. New York: Academic Press; 2015. p. 150–284.
Mujtaba G, Choi W, Lee C-G, Lee K. Lipid production by Chlorella vulgaris after a shift from nutrient-rich to nitrogen starvation conditions. Bioresour Technol. 2012;123:279–83.
Kang N, Lee DS, Yoon J. Kinetic modeling of Fenton oxidation of phenol and monochlorophenols. Chemosphere. 2002;47:915–24.
Buxton GV, Greenstock CL, Helman WP, Ross AB. Critical review of rate constants for reactions of hydrated electrons, hydrogen atoms and hydroxyl radicals (· OH/· O—in aqueous solution. J Phys Chem Reference Data. 1988;17:513–886.
Yu X-Y. Critical evaluation of rate constants and equilibrium constants of hydrogen peroxide photolysis in acidic aqueous solutions containing chloride ions. J Phys Chem Reference Data. 2004;33:747–63.
Hey DH, Watdsdsers WA. 11-Free radicals and homolytic reactions. In: Coffey S, editor. Rodd’s chemistry of carbon compounds. 2nd ed. Amsterdam: Elsevier; 1964. p. 250–432.
Ayala A, Muñoz MF, Argüelles S. Lipid peroxidation: production, metabolism, and signaling mechanisms of malondialdehyde and 4-hydroxy-2-nonenal. Oxid Med Cell Longevity. 2014;2014:1–31.
Sultana R, Perluigi M, Butterfield DA. Lipid peroxidation triggers neurodegeneration: a redox proteomics view into the Alzheimer disease brain. Free Radical Biol Med. 2013;62:157–69.
Rarata G, Florczuk W, Smetek J. Research on preparation and propulsive applications of highly concentrated hydrogen peroxide. J Aerosp Sci Technol. 2016;1:42–7.
Hutchins PM, Barkley RM, Murphy RC. Separation of cellular nonpolar neutral lipids by normal-phase chromatography and analysis by electrospray ionization mass spectrometry. J Lipid Res. 2008;49:804–13.
Navarro López E, Robles Medina A, González Moreno PA, Esteban Cerdán L, Molina Grima E. Extraction of microalgal lipids and the influence of polar lipids on biodiesel production by lipase-catalyzed transesterification. Bioresour Technol. 2016;216:904–13.
Alex S, Thanh HL, Vocelle D. Studies of the effect of hydrogen bonding on the absorption and fluorescence spectra of all-trans-retinal at room temperature. Can J Chem. 1992;70:880–7.
Morris JB. Chapter 28—Deposition of inhaled gases and vapors. In: Parent RA, editor. Comparative biology of the normal lung (second edition). San Diego: Academic Press; 2015.
Andersson H, Carlsson A-CC, Nekoueishahraki B, Brath U, Erdélyi M. Chapter two—solvent effects on nitrogen chemical shifts. In: Webb GA, editor. Annual reports on NMR spectroscopy. New York: Academic Press; 2015. p. 650–834.
Snyder L. High-performance liquid chromatography (C Horváth, ed). New York: Academic Press; 1983. p. 3–20.
Guide HPS. Burdick and Jackson laboratories. Inc, Muskegon, MI. 1980;53(9):1093.
Li Y, Naghdi FG, Garg S, Adarme-Vega TC, Thurecht KJ, Ghafor WA, Tannock S, Schenk PM. A comparative study: the impact of different lipid extraction methods on current microalgal lipid research. Microb Cell Fact. 2014;13:14.
Cao Y, Liu W, Xu X, Zhang H, Wang J, Xian M. Production of free monounsaturated fatty acids by metabolically engineered Escherichia coli. Biotechnol Biofuels. 2014;7:59.
Rice-Evans CA. Chapter 5—Formation of free radicals and mechanisms of action in normal biochemical processes and pathological states. In: Rice-Evans CA, Burdon RH, editors. New comprehensive biochemistry. New York: Elsevier; 1994. p. 240–83.
Wu M-L, Tsai K-L, Wang S-M, Wu J-C, Wang B-S, Lee Y-T. Mechanism of hydrogen peroxide and hydroxyl free radical–induced intracellular acidification in cultured rat cardiac myoblasts. Circ Res. 1996;78:564–72.
Hansen CM. Hansen solubility parameters: a user’s handbook. New York: CRC Press; 2002. p. 325–522.
Steriti A, Rossi R, Concas A, Cao G. A novel cell disruption technique to enhance lipid extraction from microalgae. Bioresour Technol. 2014;164:70–7.
Yew GY, Tham TC, Law CL, Chu D-T, Ogino C, Show PL. Emerging crosslinking techniques for glove manufacturers with improved nitrile glove properties and reduced allergic risks. Mater Today Commun. 2019;19:39–50.
Pierce KM, Synovec R. Data analysis methods. Gas Chromatogr. 2012;1184:415.
Acknowledgements
Special appreciate to Nottingham University Malaysia laboratory technologist Noor Fatihah Bt Suhaimi for assisting in gas chromatography analysis, and Mr. Yong Kai Lit for assisting in coding for radical formation time studies.
Funding
This study was financially supported by iRMC Bold2025, Universiti Tenaga Nasional, Malaysia (Grant Code: RJO10436494).
Author information
Authors and Affiliations
Contributions
GYY , MAM and PLS conceived and designed the analysis. GYY conducted the experiments. GYY, WHC and KWC analyzed and interpret the data. WHC and MAM assisted in software result analysis. GYY wrote the manuscript. KWC, MAM, TCL and PLS reviewed and edited the manuscript. TCL, MAM, and YCH funded the research. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare that they have no competing interests.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.
About this article
Cite this article
Yew, G.Y., Chew, K.W., Malek, M.A. et al. Hybrid liquid biphasic system for cell disruption and simultaneous lipid extraction from microalgae Chlorella sorokiniana CY-1 for biofuel production. Biotechnol Biofuels 12, 252 (2019). https://doi.org/10.1186/s13068-019-1591-8
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13068-019-1591-8