Abstract
We numerically propose a dual-band absorber in the infrared region based on periodic elliptical graphene-black phosphorus (BP) pairs. The proposed absorber exhibits near-unity anisotropic absorption for both resonances due to the combination of graphene and BP. Each of the resonances is independently tunable via adjusting the geometric parameters. Besides, doping levels of graphene and BP can also tune resonant properties effectively. By analyzing the electric field distributions, surface plasmon resonances are observed in the graphene-BP ellipses, contributing to the strong and anisotropic plasmonic response. Moreover, the robustness for incident angles and polarization sensitivity are also illustrated.
Avoid common mistakes on your manuscript.
Introduction
Graphene is a two-dimensional material with carbon atoms arranged in a honeycomb lattice [1, 2]. Various graphene-based photonic devices have been developed in the recent years due to their ultracompact size and unique light-graphene interaction [3,4,5,6]. As one of its most significant applications, metamaterial absorbers based on graphene have attracted burgeoning amount of interest due to their strong and tunable plasmonic response [7,8,9,10]. However, several applications that require high on-off ratio are restricted due to the zero or near-zero band gap of graphene [11]. As an alternative two-dimensional material, black phosphorus (BP), a monolayer of phosphorus atoms arranged in a hexagonal lattice with a puckered structure [12], has also received a surge of research interest recently. It possesses exceptional optical and electronic properties, such as in-plane anisotropy, thickness-dependent tunable band gap [13], and high carrier density and mobility [14]. Over the past few years, in the infrared region, researchers have investigated numerous structures to enhance the light-BP interaction strength in the metamaterial based on BP [15,16,17]. Nevertheless, the plasmonic resonance of BP-based absorber is hardly to be tuned flexibly and effectively, and they normally suffer from relatively low absorption rate with moderate doping level. This is attributed to the fact that the resonance strength in monolayer BP is rather weak, limiting its anisotropic potentials. Thus, graphene-BP-based plasmonic absorbers have been proposed utilizing the hybridization of graphene and BP to achieve strong and anisotropic plasmonic absorption [18,19,20]. However, the previous reported graphene-BP-based absorbers generally require relatively complicated fabrication technique or possess single absorption band, impeding their further applications for imaging, biosensing, and communication systems.
In our work, an anisotropic dual-band infrared absorber is numerically proposed using periodic elliptical graphene-BP pairs, which is ease of fabrication. The independent tunability of resonance by geometric size and doping level is demonstrated. Electric field distributions are plotted to reveal the physical mechanism. The incident angle tolerance and polarization sensitivity are also illustrated.
Methods
The proposed absorber is made up of transverse and longitudinal elliptical graphene-BP pairs deposited on a SiO2 layer as shown in Fig. 1. A hexagonal boron nitride (hBN) layer is inserted between monolayer graphene and BP as an insulating spacer to prevent carrier transport between them and guarantee high carrier mobility. The parameters of SiO2 and hBN are obtained from Ref. 21 and Ref. 22 respectively. The simulations are carried out by COMSOL Multiphysics to investigate the dual-band properties, which is based on finite element method (FEM) in the frequency domain. We apply Floquet periodicity as the boundary conditions in both x- and y- directions. A port with infrared wave excitation is set upon the top surface of the computational domain, while perfect electric conductor (PEC) boundary condition is set on the bottom surface. Tetrahedral meshes with user-controller mesh density are applied for the entire domain.
In the simulation, both graphene and BP are treated as two-dimensional surface with surface conductivities instead of bulk materials with permittivity tensors. This assumption solves the problems of thickness definition for ultrathin materials and low computational efficiency [23].
To describe the surface conductivity of graphene σ(ω), we use the well-known Kubo formulas as below [24]:
According to Eq. 1, σ(ω) consists of the intraband and interband counterparts, namely σintra and σinter. ω is the radian frequency, μc is the chemical potential, Г is the scattering rate, and T is the Kelvin temperature. ħ, e, ξ, and kB are the reduced Planck constant, electron charge, electron energy, and Boltzmann constant, respectively.
In the infrared region, since the incident photon can hardly excite the interband transition, the light-graphene interaction is dominated by the intraband transition. Particularly, when μc ≫ kBT, Kubo formulas can be further simplified to Eq. 5:
Thus, the surface conductivity of graphene is dependent on the values of ω, Г, and μc. Here, Г is assumed as 0.3 meV and μc is assumed to be 0.7 eV according to the previous work [25, 26].
On the other hand, we calculate the surface conductivity σj of BP with a simple semi-classical Drude model [27]:
where ns is the carrier density relating with the doping level. We choose ns = 1.9 × 1013 cm−2 and ГBP = 10 meV according to the previous reference [16]. j is the concerned direction, so σx and σy are determined by the electron mass along x- and y-direction, respectively. mx and my can be further calculated by:
where m0 is the standard electron mass, and Δ and a are the band gap and scale length for BP monolayer, respectively. By substituting Eqs. 10–12 into Eq. 8 and Eq. 9, one can obtain the electron mass along armchair (x-) and zigzag (y-) direction. The discrepancy between them contributes to the anisotropic surface conductivity of BP.
Results and Discussion
To illustrate the anisotropic absorption characteristic of the proposed absorber, we first simulate and compare the absorption spectra with individual graphene layer, individual BP layer, and graphene-BP pairs. As can been observed in Fig. 2a, the plasmonic response of graphene is isotropic with two obvious absorption peaks at 9.9 μm and 15.4 μm, independent on the polarization. On the other hand, although the plasmon resonance of BP is anisotropic, its strength is quite weak for either TE (< 12.7%) or TM (< 0.7%) incidence. By combining the advantages of graphene and BP, graphene-BP pairs exhibit both strong and anisotropic plasmonic responses. For TE incidence, the two absorption peaks are located at 8.8 μm and 14.1 μm, with absorption rates larger than 90%. For TM incidence, the wavelengths of maximum absorption are shifted to 9.5 μm and 15.4 μm, respectively. The polarization extinction ratio can be defined as PER = 10 × log(R1/R0), where R1 and R0 denote the reflectance (R = 1-A, A represents the absorbance) of different polarizations at the same wavelength, then the maximum PER of each resonance can reach up to 23 dB and 25 dB at λ = 9.5 μm and λ = 14.1 μm, respectively. Therefore, the proposed absorber can be utilized as a dual-band reflective polarizer with high performance.
We next analyze the absorption spectra with different geometric configurations to demonstrate the tunable dual-band absorption property in Fig. 2b–d. In Fig. 2b, the first absorption peaks have redshifts as a increases from 42 to 52 nm for both polarizations, while second resonant frequencies are almost unchanged. On the other hand, as shown in Fig. 2c, by increasing the long axis length b, the second resonances are redshifted as well, while the first absorption peaks remain constant for TE and TM polarization. Therefore, the dual absorption peaks can be tuned independently by varying the corresponding axis length in the elliptical graphene-BP pairs. Moreover, the thickness of dielectric layer also plays a critical role in the performance for the proposed device, which acts as a Fabry-Perot resonator formed by the graphene-BP metasurface and the PEC substrate. Thus, the absorption spectra with different td are plotted in Fig. 2d. As td increases from 0.95 to 1.75 μm, the first absorption peaks for TE and TM polarization have a dramatic drop, while the second peaks increase at first then decrease sharply. As a consequence, there is an optimal thickness td that maximizes the dual absorption peaks of the proposed absorber.
In order to elucidate the physical insight, we further reveal the electric field intensity distributions at different wavelengths in Fig. 3. For TE incidence, the electric field is in the armchair (x-) direction. At the first peak (λ = 8.8 μm), the incident infrared light can excite electrons in graphene and BP to oscillate in the transverse direction, leading to the concentration of electric field at the short axis ends of the longitudinal ellipse as shown in Fig. 3a. At λ = 14.1 μm, the localized electric field is enhanced at the long axis ends of the transverse ellipse. On the other hand, TM incidence with electric field in the zigzag (y-) direction can excite electrons to vibrate along the longitudinal direction at the absorption peak of 9.5 μm, leading to concentrated field distributions at the short axis ends of the transverse ellipse. Besides, at λ = 15.4 μm, the enhancement of electric field is focused at the long axis ends of the longitudinal ellipse. Therefore, the resonance wavelengths are directly related to the finite oscillation length of the induced dipoles in both transverse and longitudinal elliptical graphene and BP pairs.
One can tune the anisotropic dual-band absorption performance effectively by varying the geometric dimensions as demonstrated in Fig. 2b–d. Meanwhile, the surface conductivities of graphene and BP can also be manipulated by varying μc and ns according to graphene and BP model formulas as mentioned above. μc and ns represent the doping level of graphene and BP that can be altered after geometric fabrication. Thus, performances of the proposed absorber with different μc and ns are depicted in Fig. 4. Considering the practical situation, μc is chosen between 0.4 and 0.8 eV from the previous work verified by experiments [28]. In the previous reported work [29], the maximum theoretical value for ns of BP was demonstrated to be 2.6 × 1014 cm−2, so a moderate ns is chosen between 1013 cm−2 and 1014 cm−2 in the simulation. In Fig. 4a, when μc = 0.4 eV, the first absorption peak is located at 10.9 μm and the second one is located at 17.1 μm. As μc increases to 0.8 eV, the two resonant wavelengths are blueshifted to 8.4 μm and 13.4 μm. Similarly for TM polarization, the dual absorption peaks are blueshifted from 12.4 and 19.8 μm to 8.9 and 14.4 μm, respectively, with μc increasing from 0.4 to 0.8 eV as shown in Fig. 4b. For individual patterned BP, the resonance wavelength λp can be calculated as \( {\lambda}_p\propto \sqrt{L/{n}_s} \), where L is the effective oscillation length [27]. Thus, if L is fixed, the absorption spectra exhibit an obvious blueshift as ns increases for TE polarization as plotted in Fig. 4c. For TM polarization, the absorption peaks are also slightly blueshifted as ns increases from 1013 cm−2 to 1014 cm−2 as demonstrated in Fig. 4d.
In the practical applications, tolerance of wide incident angles is preferred for infrared absorbers. Therefore, absorption spectra under oblique incidences are elaborated. In Fig. 5a, it is observed that, for TE polarization, the first absorption peak remains larger than 80% when θ increases to 52°, while the second absorption peak maintains above 80% even when θ increases to 80°. When θ > 46°, the second resonant wavelength is redshifted gradually as θ becomes larger. For TM incidence, when θ is less than 62°, the absorption rate at the first peak maintains larger than 90%, while the resonant wavelength keeps constant at λ = 9.5 μm as shown in Fig. 5b. Besides, for the second resonance, the peak absorption remains larger than 80% with θ up to 60°, then drops slightly with the increase of θ. The excellent angular stability originates from the common feature of Fabry-Perot resonators, which are robust for oblique incident angles [30].
Absorption spectra under normal incidence with different polarization angles φ are presented in Fig. 5c to investigate the polarization dependence of the proposed absorber. We assume the polarization angle of TE polarization to be 0°. One can see from Fig. 5c that, as φ increases from 0 to 90°, the absorption spectrum turns out to be the same as the TM polarization in Fig. 2a. When 0° < φ < 90°, the incidence will excite electrons in BP to oscillate in both armchair and zigzag directions due to its x- and y- components of the incident electric field. Consequently, surface plasmon resonances can be induced simultaneously in armchair and zigzag directions of BP.
Conclusions
In conclusions, we have proposed an anisotropic dual-band infrared absorber consisting of periodic transverse and longitudinal graphene-BP ellipses. The maximum PER at each resonance can reach up to 23 dB and 25 dB. The dual anisotropic resonances are attributed to the induced electric dipoles located at the ends of short and long axes. By adjusting the lengths of short axis and long axis, the first and second absorption peaks can be independently tuned, respectively. Moreover, the resonant absorption bands can also be tuned by changing the corresponding doping level of graphene and BP. Besides, high absorption rates at both peaks can be achieved under oblique incidence for any polarization. The proposed absorber can be utilized as a tunable reflective polarizer and novel infrared sensor.
Availability of Data and Materials
All data are fully available without restriction.
Abbreviations
- BP:
-
Black phosphorus
- FEM:
-
Finite element method
- hBN:
-
Hexagonal boron nitride
- PEC:
-
Perfect electric conductor
- TE:
-
Transverse electric
- TM:
-
Transverse magnetic
References
Novoselov KS, Geim AK, Morozov SV, Jiang D, Zhang Y, Dubonos SV, Grigorieva IV, Firsov AA (2004) Electric field effect in atomically thin carbon films. Science 306:666–669
Geim AK, Novoselov KS (2007) The rise of graphene. Nat Mater 6:183–191
Li H, Wang L, Zhang H, Huang Z, Sun B, Zhai X, Wen S (2014) Graphene-based mid-infrared, tunable, electrically controlled plasmonic filter. Appl Phys Express 7:024301
Cai Y, Zhu J, Liu QH (2015) Tunable enhanced optical absorption of graphene using plasmonic perfect absorbers. Appl Phys Lett 106:043105
Wu B, Zu H, Xue B, Zhao Y, Cheng QS (2019) Flexible wideband power divider with high isolation incorporating spoof surface plasmon polaritons transition with graphene flake. Appl Phys Express 12:022008
Cai Y, Xu KD, Guo R, Zhu J, Liu QH (2018) Graphene-based plasmonic tunable dual-band bandstop filter in the far-infrared region. IEEE Photonics J 10:5900709
Xiao S, Wang T, Liu Y, Xu C, Han X, Yan X (2016) Tunable light trapping and absorption enhancement with graphene ring arrays. Phys Chem Chem Phys 18:26661–26669
Cai Y, Xu KD (2018) Tunable broadband terahertz absorber based on multilayer graphene-sandwiched plasmonic structure. Opt Express 26:31693–31705
Zhang K, Yuan Y, Ding X, Ratni B, Burokur SN, Wu Q (2019) High-efficiency metalenses with switchable functionalities in microwave region. ACS Appl Mater Interfaces 11:28423–28430
Yuan Y, Zhang K, Ding X, Ratni B, Burokur SN, Wu Q (2019) Complementary transmissive ultra-thin meta-deflectors for broadband polarization-independent refractions in the microwave region. Photonic Res 7:80–88
Chen Y, Jiang G, Chen S, Guo Z, Yu X, Zhao C, Zhang H, Bao Q, Wen S, Tang D, Fan D (2015) Mechanically exfoliated black phosphorus as a new saturable absorber for both Q-switching and mode-locking laser operation. Opt Express 23:12823–12833
Liu H, Neal AT, Zhu Z, Luo Z, Xu X, Tomanek D, Ye PD (2014) Phosphorene: an unexplored 2D semiconductor with a high hole mobility. ACS Nano 8:4033–4041
Li L, Yu Y, Ye GJ, Ge Q, Ou X, Wu H, Feng D, Chen XH, Zhang Y (2014) Black phosphorus field-effect transistors. Nat Nanotechnol 9:372–377
Saito Y, Iwasa Y (2015) Ambipolar insulator-to-metal transition in black phosphorus by ionic-liquid gating. ACS Nano 9:3192–3198
Liu Z, Aydin K (2016) Localized surface plasmons in nanostructured monolayer black phosphorus. Nano Lett 16:3457–3462
Wang J, Jiang Y (2017) Infrared absorber based on sandwiched two-dimensional black phosphorus metamaterials. Opt Express 25:5206–5216
Qing YM, Ma HF, Tie JC (2018) Strong coupling between magnetic plasmons and surface plasmons in a black phosphorus-spacer-metallic grating hybrid system. Opt Lett 43:4985–4988
Nong J, Wei W, Wang W, Lan G, Shang Z, Yi J, Tang L (2018) Strong coherent coupling between graphene surface plasmons and anisotropic black phosphorus localized surface plasmons. Opt Express 26:1633–1644
Hong Q, Xiong F, Xu W, Zhu Z, Liu K, Yuan X, Zhang J, Qin S (2018) Towards high performance hybrid two-dimensional material plasmonic devices: strong and highly anisotropic plasmonic resonances in nanostructured graphene-black phosphorus bilayer. Opt Express 26:22528–22535
Cai Y, Xu KD, Feng N, Guo R, Lin H, Zhu J (2019) Anisotropic infrared plasmonic broadband absorber based on graphene-black phosphorus multilayers. Opt Express 27:3101–3112
Palik ED (1998) Handbook of optical constants of solids, vol 3. San Diego: Academic, p 207
Ishii T, Sato T (1983) Growth of single crystals of hexagonal boron nitride. J Cryst Growth 61:689–690
Zhu J, Cheng J, Zhang L, Liu QH (2017) Modeling of 2D graphene material for plasmonic hybrid waveguide with enhanced near-infrared modulation. Mater Lett 186:53–56
Hanson GW (2008) Dyadic Green’s functions and guided surface waves for a surface conductivity model of graphene. J Appl Phys 103:064302
Diaz J, Morote M, Carrier J (2013) Plane wave excitation-detection of non-resonant plasmons along finite-width graphene strips. Opt Express 21:24856–24872
Ye L, Sui K, Liu Y, Zhang M, Liu QH (2018) Graphene-based hybrid plasmonic waveguide for highly efficient broadband mid-infrared propagation and modulation. Opt Express 26:15935–15947
Low T, Roldán R, Wang H, Xia F, Avouris P, Moreno LM, Guinea F (2014) Plasmons and screening in monolayer and multilayer black phosphorus. Phys Rev Lett 113:106802
Jiang Y, Zhang H, Wang J, Gao C, Wang J, Cao W (2018) Design and performance of a terahertz absorber based on patterned graphene. Opt Lett 43:4296–4299
Luo Z, Liu M, Guo Z, Jiang X, Luo A, Zhao C, Yu X, Xu W, Zhang H (2015) Microfiber-based few-layer black phosphorus saturable absorber for ultra-fast fiber laser. Opt Express 23:20030–20039
Luo X, Zhai X, Wang L, Lin Q (2018) Enhanced dual-band absorption of molybdenum disulfide using a plasmonic perfect absorber. Opt Express 26:11658–11666
Funding
This work was supported by the National Natural Science Foundation of China (51702271), the Young and Middle-aged Teachers Education and Scientific Research Foundation of Fujian Province, China (JAT170407), and the High Level Talent Project of Xiamen University of Technology, China (YKJ16016R).
Author information
Authors and Affiliations
Contributions
CY and LS conceived the idea and wrote the manuscript. ZY and WX undertook the simulations. XK analyzed the data. GR and JW supervised the project. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Cai, Y., Li, S., Zhou, Y. et al. Tunable and Anisotropic Dual-Band Metamaterial Absorber Using Elliptical Graphene-Black Phosphorus Pairs. Nanoscale Res Lett 14, 346 (2019). https://doi.org/10.1186/s11671-019-3182-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s11671-019-3182-9