Abstract
We predict the CH4-sensing performance of monolayer MoX2(S, Se, Te) with X-vacancy, Mo-vacancy, and divacancy by the density functional theory (DFT). The results demonstrate that the combination of different sixth main group elements with Mo atom has different adsorption behaviors for CH4 gas molecule. Compared with MoX2, MVX, MVMo, and MVD generally exhibit better adsorption properties under the same conditions. In addition, different defects will have different effects on adsorption behavior of the systems, the MVD(MoTe2) has the better adsorption, the better charge transfer, and the shortest distance in these systems. The results are proposed to predict the CH4 gas molecule adsorption properties of MVD(MoTe2) and would help in guiding experimentalists to develop better materials based on MoX2 for efficient gas detection or sensing applications.
Avoid common mistakes on your manuscript.
Introduction
Methane (CH4) is the simplest organic compound with colorless and tasteless gas [1,2,3,4], which is basically non-toxic to human beings, the oxygen content in the air will obviously decrease when the concentration of methane is too high, which makes people suffocate. When the concentration of methane reaches 25–30% in the air, it will cause headaches, dizziness, fatigue, inattention, rapid breathing and heartbeat, and ataxia [5,6,7]. Since the rise of graphene [8, 9] and the discovery of topological insulators [10], a lot of interesting physics have been found in systems with reduced dimensions. Other two-dimensional (2D) material, such as monolayers or few-layer systems (nanolayers) of transition-metal dichalcogenides (TMDs), gain importance because of their intrinsic band gap [11,12,13,14,15]. TMDs are MX2-type compounds where r(S, Se, Te) [16,17,18,19]. These materials form layered structures in which the different X-M-X layers are held together by weak van der Waals forces [20,21,22,23,24,25,26]. Yi Li [27] studied that the adsorption energy of COF2 on Ni-MoS2 was better than CF4, and Ni-MoS2 acted as electron donor and obvious charge transfer was observed. Soumyajyoti Haldar [28] reported that structural, electronic, and magnetic properties of atomic scale defects in 2D transition metal dichalcogenides MX2, and different vacancy had a great effect on different 2D dichalcogenides MX2, it is likely that band gap, density of states, some properties, and so on. Janghwan Cha [29] used different functionals to show the relatively binding energies about gas molecule and MoX2. The optPBE-vdW functionals showed relatively large binding energies. Furthermore, the TMDs are promising materials to realize gas sensors, so we study the effect of many defects on MoX2(X=S, Se, Te) for structure, band gap [30,31,32], adsorption energy, charge transfer, etc. This paper studied the interaction of methane with monolayer MoX2 by first-principle simulation (see Fig. 1). The green color ball is Mo atom, and the yellow color ball is X atom, the distance of d1 for S-S, Se-Se, and Te-Te is 3.190 Å, 3.332 Å, and 3.559 Å, respectively, the distance of d2 is the same as the three cases of d1. This work was based on DFT, and the adsorption energy, charge transfer, adsorption distance, and density of states (DOS) of CH4 gas molecule on MoX2 were studied.
Method and Theory
A 4 × 4 supercell of MoX2 (32 X atoms and 16 Mo atoms) and CH4 gas molecule adsorbed onto it was built in Materials studio [33,34,35,36]. DMol3 [37] software was used for calculation. In this paper, the Perdew, Burke, and Ernzerhof (PBE) [38, 39] functions with generalized gradient approximation (GGA) were selected to describe the exchange energy Vxc. The Mo was generated in 4p65s14d5 configuration and another was used for the generation of the valence electrons of X. The Brillouin zone of MoX2 was sampled using a 6 × 6 × 1 k-point grid and Methfessel-Paxton smearing of 0.01 Ry. The cutoff energy was 340 eV with self-consistence-field (SCF) converged of 1.0 × 10−5 eV. All the atomic structures were relaxed until the maximum displacement tolerance of 0.001 Å and maximum force tolerance of 0.03 eV/Å [40, 41].
We calculated the adsorption energy (Ead) in the adsorbed systems, which was defined in the following equation:
Where, EMoX2 + CH4 gas molecule, EMoX2 and ECH4 gas molecule represent the energies of the monolayer MoX2 adsorbed system, monolayer MoX2, and a CH4 gas molecule, respectively. All energies achieve the best optimization after structural optimization. We used Mulliken’s population analysis to study the charge transfer.
Results and Discussion
Firstly, we discussed the geometric and electric structures of the four MoX2 substrates (ee in Fig. 2). The bond length of Mo-S, Mo-Se, and Mo-Te were 2.426 Å, 2.560 Å, and 2.759 Å, which were in good agreement with experimental value of 2.410 Å (MoS2) [42, 43], 2.570 Å (MoSe2) [44] and 2.764 Å (MoTe2) [45], the four structures MoX2 were in this paper, pristine MoX2, MVX(one X atom vacancy), MVMo(one Mo atom vacancy), and MVD(one X atom and one Mo atom vacancy) respectively. Full structural relaxation showed that the stretching X-Mo bond length from 2.420 Å to 2.394 Å (MVS), 2.420 Å to 2.398 Å (MVMo), and the main reason was that the absence of atoms enhanced the interaction between the adjacent Mo atoms and other S atoms, the chemical bond became stronger and the bond length became shorter.
Figure 3a–c displayed the calculated adsorption energy, charge transfer, and adsorption distance of CH4/MoX2 system. Before the adsorption, the distance between the CH4 gas molecules and the molybdenum disulfide was 3.6 Å. The CH4 gas molecule obtained about − 0.001 e to − 0.009 e from the four systems of MoS2 sheet, − 0.009 e to − 0.013 e from the four systems of MoSe2 sheet and − 0.014 e to − 0.032 e from the four systems of MoTe2 sheet, respectively, which means that CH4 acted as an acceptor. Inclusion of the van der Waals correction enhances the adsorption energies of CH4 gas molecule by − 0.31 eV to − 0.46 eV on the four systems of MoS2 systems, by − 0.07 eV to − 0.50 eV on the four systems of MoSe2 systems, and by − 0.30 eV to − 0.52 eV on the four systems of MoTe2 system, and 0.01 eV was usually thought within the error range. It was obvious that the adsorption distance was the shortest in the case of S atom defects and divacancy defects. To sum up the above data, we saw that the adsorption effect was the best under the condition of divacancy defected.
Adsorption of CH4 Gas Molecule on Monolayer MoS2
In order to have a clear understanding about the bonding mechanism of CH4 gas molecule on pure and defected MoS2 (including MVs, MVMo, and MVD), we analyzed the corresponding density of states (DOS) for adsorbed CH4 gas molecule in adsorption structures. Comparing four systems, the adsorption effect of CH4 gas molecule on pure and defected MoS2 (including MVs, MVMo, and MVD) were further investigated. The DOS (Fig. 4) showed that there was a certain change in the vicinity of the Fermi level, which was the same as the general DOS form. The energy band gap of four systems was observed along the gamma point (G) noticed to be 1.940 eV (MoS2), 1.038 eV (MVS), 0.234 eV (MVMo), and 0.209 eV (MVD). Moreover, the observed energy band gap of MoS2 nanosheet was in good agreement with other reported theoretical work (1.78 eV [39], 1.80 eV [40]) and experimental work (1.90 eV [41], 1.98 eV [42]). Meantime, monolayers MoS2 had five peak values, the peak was − 12.2 eV, − 5 eV, − 4 eV, − 2 eV, and − 1 eV which were ascribed to the S atom in MoS2 and the Mo atom in MoS2. However, the DOS of four systems (Fig. 4) showed that the electronic level of CH4 gas molecule has a peak for about − 3 eV which was closed to Fermi level. It was contributed to the conduction band in the system and affects the conductivity of the system. Comparing four systems, the peak of − 12.5 eV MVs was obviously much lower than MoS2 because of the defect of the S atom in the MoS2. And the defects of the Mo atom do not have much effect; however, the contribution at the conduction zone was still decreasing. As shown in Fig. 3 b, obviously, the band around the 0 eV was getting smaller and smaller, and the curve was more and more stable. In summary, there was no bond between CH4 gas molecule and MoS2, and the electron transfer and adsorption energy were small, and the adsorption was not very strong, which was obviously physical adsorption.
Adsorption of CH4 Gas Molecule on Monolayer MoSe2
We studied the adsorption of CH4 gas molecule on four systems of MoSe2, it could be seen from the DOS (Fig. 5) that the electron energy levels of CH4 gas molecule in the four adsorption orientations were close to the Fermi level, which had a certain influence on the conductivity of the system, and the band gap system was so small, same as adsorption of MoS2. Meantime, the DOS (Fig. 5) also showed that the Se atoms in MoSe2 had five peak values, the peak was − 12 eV, − 5 eV, − 4 eV, − 3 eV, and − 2 eV, the Mo atom in MoSe2 had overlapping peaks at about 0.5 eV and 2 eV. Compared with MoS2, Se contributed more to the system than S in MoS2 below the fermi level, and the energy band gaps of four systems were observed along the gamma point (G) that was noticed to be 1.680 eV (MoSe2), 1.005 eV (MVSe), 0.094 eV (MVMo), and 0.024 eV(MVD). The band was narrower and more stable around the 0 eV. Therefore, it could be confirmed that the adsorption properties and the CH4 gas molecule on the four systems were physisorption.
Adsorption of CH4 Gas Molecule on Monolayer MoTe2
We studied the adsorption of CH4 gas molecule on four systems of MoTe2, the DOS (Fig. 6) of CH4 gas molecule on the MoTe2 were analyzed. As shown in Fig. 6, the electronic levels of CH4 in the four MoTe2 systems were short with CH4/MoS2 systems and CH4/MoSe2 systems, and the energy band gap of four systems were observed along the gamma point (G) was noticed to be 1.261 eV (MoTe2), 0.852 eV (MVTe), 0 eV (MVMo), and 0.316 eV (MVD). One of the strangest things of all was the defect of the Mo atom, which allowed the system to be transformed from semiconductor to metal. Meantime, the DOS (Fig. 6) also showed that the Te atoms in MoTe2 had four peaks value, the peak was − 10 eV, − 5 eV, − 3 eV, and − 1 eV and the Mo atom in MoSe2 had overlapping peaks at about 1 eV.
In general, on the basis of the adsorption behaviors of CH4 gas molecule in different systems, the CH4 gas molecule adsorbed by the MVX could have two peaks near the Fermi level. The DOS between the two spikes was not zero but very wide, which reflected the strong covalent property of the system. To summarize all the data, the MVTe might become an ideal sensing material for the detection of CH4 gas molecule.
Conclusions
We carried out density-functional-GGA studies to study the interaction of an isolated CH4 gas molecule on MoX2 (X=S, Se, Te). The results indicated that the different defects changed the electrical properties of MoX2 greatly, and our results revealed a weak interaction between the CH4 gas molecules and MoX2 monolayer, which indicated the physical nature of the adsorption. The total electron density plots confirmed the physisorption of gas molecules on the MoX2 surface, as the material weakly interacts with the CH4 gas molecules without the formation of covalent bonds at the interface region. Furthermore, the structure of MVD has a good band gap, semiconductor property, the best adsorption energy, and the stronger charge transfer for the CH4 gas molecule. Besides, the electronic band structures of the sensing system were altered upon the adsorption of gas molecules. MoTe2 had the highest adsorption energy (− 0.51 eV), the shortest intermolecular distance (2.20 Å), and the higher charge transfer (− 0.026 e). At last from the analysis of these three materials, it could be seen that MVD (MoTe2) had the best adsorption effect on CH4 gas molecule. The calculated results thus suggested a theoretical basis for the potential application of MVD(MoTe2) monolayers in the CH4 based gas sensor devices.
Availability of Data and Materials
All data are fully available without restriction.
Abbreviations
- CH4:
-
Methane
- DOS:
-
Density of states
- Ea:
-
Adsorption energy
References
Wetchakun K, Samerjai T, Tamaekong N et al (2011) Semiconducting metal oxides as sensors for environmentally hazardous gases [J]. Sens Actuators B 160(1):580–591
Abbasi A, Sardroodi JJ (2016) N-doped TiO2 anatase nanoparticles as a highly sensitive gas sensor for NO2 detection: insights from DFT computations [J]. Environ Sci: Nano 3(5):1153–1164
Ueda T, Bhuiyan MMH, Norimatsu H et al (2008) Development of carbon nanotube-based gas sensors for NOx gas detection working at low temperature [J]. Physica E: Low-dimensional Systems and Nanostructures 40(7):2272–2277
Abbasi A, Sardroodi JJ (2016) Theoretical study of the adsorption of NOx on TiO2/MoS2 nanocomposites: a comparison between undoped and N-doped nanocomposites[J]. J Nanostruct Chem
Abbasi T, Abbasi SA (2011) ‘Renewable’hydrogen: prospects and challenges [J]. Renew Sustain Energy Rev 15(6):3034–3040
Reddy RG (2006) Fuel cell and hydrogen economy [J]. J Mater Eng Perform 15(4):474–483
Cheng X, Shi Z, Glass N et al (2007) A review of PEM hydrogen fuel cell contamination: Impacts, mechanisms, and mitigation [J]. J Power Sources 165(2):739–756
Novoselov KS, Morozov SV, Mohinddin TMG et al (2010) Electronic properties of graphene [J]. Physica Status Solidi 244(11):4106–4111
Jose D, Datta A (2013) Structures and chemical properties of silicene: unlike graphene [J]. Acc Chem Res 47(2):593–602
Hasan MZ, Kane CL (2010) Colloquium: topological insulators [J]. Rev Mod Phys 82(4):3045
Stankovich S, Dikin DA, Dommett GHB et al (2006) Graphene-based composite materials [J]. Nature 442(7100):282
Nijamudheen A, Bhattacharjee R, Choudhury S et al (2015) Electronic and chemical properties of germanene: the crucial role of buckling [J]. J Phys Chem C 119(7):3802–3809
Chowdhury C, Jahiruddin S, Datta A (2016) Pseudo-Jahn–Teller distortion in two-dimensional phosphorus: origin of black and blue phases of phosphorene and band gap modulation by molecular charge transfer [J]. J Phys Chem Lett 7(7):1288–1297
Bhattacharjee R, Majumder T, Datta A (2019) Analysis of pseudo jahn–teller distortion based on natural bond orbital theory: case study for silicene [J]. J Comb Chem
Ni J, Yang B, Jia F et al (2018) Theoretical investigation of the sensing mechanism of the pure graphene and AL, B, N, P doped mono-vacancy graphene-based methane[J]. Chem Phys Lett 710:221–225
Qiao X, Chao Z, Shao Q et al Structural characterization of corn stover lignin after hydrogen peroxide presoaking prior to ammonia fiber expansion pretreatment [J]. Energy Fuels, 2018: acs. energyfuels. 8b00951
Zhao C, Yan C, Ma Z et al (2017) Optimization of liquid ammonia pretreatment conditions for maximizing sugar release from giant reed (Arundo donax L) [J]. Biomass Bioenergy 98(2):61–69
Zhao C, Shao Q, Ma Z et al (2016) Physical and chemical characterizations of corn stalk resulting from hydrogen peroxide presoaking prior to ammonia fiber expansion pretreatment [J]. Ind Crops Prod 83(2):86–93
Zhao C, Qiao X, Cao Y et al (2017) Application of hydrogen peroxide presoaking prior to ammonia fiber expansion pretreatment of energy crops. Fuel 205:184–191
Mak KF, Lee C, Hone J et al (2010) Atomically thin MoS 2: a new direct-gap semiconductor [J]. Phys Rev Lett 105(13):136805
Pan H, Zhang YW (2012) Edge-dependent structural, electronic and magnetic properties of MoS2 nanoribbons [J]. J Math Chem 22(15):7280–7290
Ataca C, Sahin H, Ciraci S (2012) Stable, single-layer MX2 transition-metal oxides and dichalcogenides in a honeycomb-like structure [J]. J Physic Chem C 116(16):8983–8999
Pan H, Zhang YW (2012) Tuning the electronic and magnetic properties of MoS2 nanoribbons by strain engineering [J]. J Phys Chem C 116(21):11752–11757
Yin Z, Li H, Li H et al (2011) Single-layer MoS2 phototransistors [J]. ACS Nano 6(1):74–80
Frindt RF (1966) Single crystals of MoS2 several molecular layers thick [J]. J App Phys 37(4):1928–1929
Joensen P, Frindt RF, Morrison SR (1986) Single-layer MoS2 [J]. Mater Res Bull 21(4):457–461
Li Y, Zhang X, Chen D et al (2018) Adsorption behavior of COF2 and CF4 gas on the MoS2 monolayer doped with Ni: A first-principles study [J]. App Surf Sci 443:274–279
Haldar S, Vovusha H, Yadav MK et al (2015) Systematic study of structural, electronic, and optical properties of atomic-scale defects in the two-dimensional transition metal dichalcogenides MX2 (M= Mo, W; X= S, Se, Te) [J]. Phys Rev B 92(23):235408
Cha J, Sung D, Min KA et al (2018) Van der Waals density functional theory study of molecular adsorbates on MoX2 (X= S, Se or Te) [J]. J Korean Phys Soc 73(1):100–104
Li H, Huang M, Cao G (2016) Markedly different adsorption behaviors of gas molecules on defective monolayer MoS2: a first-principles study [J]. Phys Chem Chem Phys 18(22):15110–15117
Lee C, Hone J, Shan J et al (2010) Atomically 392 Thin MoS2: A new direct-gap semiconductor [J]. Phys. Rev. Lett 393(105):136805
Ma D, Wang Q, Li T et al (2016) Repairing sulfur vacancies in the MoS2 monolayer by using CO, NO and NO2 molecules [J]. J Mat Chem C 4(29):7093–7101
Shokri A, Salami N (2016) Gas sensor based on MoS2 monolayer[J]. Sens Actuators B 236:378–385
Yue Q, Shao Z, Chang S et al (2013) Adsorption of gas molecules on monolayer MoS 2 and effect of applied electric field [J]. Nanoscale Res Lett 8(1):425
Zhao S, Xue J, Kang W (2014) Gas adsorption on MoS2 monolayer from first-principles calculations [J]. Chem Physics Lett 595:35–42
Ray SJ (2016) First-principles study of MoS2, phosphorene and graphene based single electron transistor for gas sensing applications [J]. Sens Actuators B: Chem 222:492–498
O.-T W J. Molecular mechanics: by U. Burkert and N. L. Allinger, American Chemical Society, Washington. Journal of Molecular Structure Theochem [J],109(3–4) (1984) 401-401.
Kohn W, Sham LJ (1965) Self-consistent equations including exchange and correlation effects [J]. Phys Rev 140(4A):A1133
Perdew JP (1997) JP Perdew, K. Burke, and M. Ernzerhof, Phys. Rev. Lett. 78, 1396 (1997) [J]. Phys. Rev. Lett. 78:1396
Monkhorst HJ, Pack JD (1976) Special points for Brillouin-zone integrations [J]. Phys Rev B 13(12):5188
Becke AD (1993) A new mixing of Hartree–Fock and local density-functional theories [J]. J Chem Phys 98(2):1372–1377
Komsa HP, Krasheninnikov AV (2015) Native defects in bulk and monolayer MoS 2 from first principles [J]. Phys Rev B 91(12):125304
Zahid F, Liu L, Zhu Y et al (2013) A generic tight-binding model for monolayer, bilayer and bulk MoS2 [J]. Aip Advances 3(5):052111
Sharma M, Jamdagni P, Kumar A et al (2016) Interactions of gas molecules with monolayer MoSe2: A first principle study [C]//AIP Conference Proceedings. AIP Publishing 1731(1):140045
Fan Z, Wei-Bing Z, Bi-Yu T (2015) Electronic structures and elastic properties of monolayer and bilayer transition metal dichalcogenides MX2 (M= Mo, W; X= O, S, Se, Te): a comparative first-principles study [J]. Chinese Physics B 24(9):097103
Acknowledgements
We also thank the College of Materials Science and Engineering, Anhui University of Science and Technology, for its assistance with the MS simulations.
Funding
The financial supports for this work from the Natural science fund for colleges and universities in Jiangsu Province (17KJB510007, 17KJB535001, 18KJB510005).
Author information
Authors and Affiliations
Contributions
JR and YX designed and carried out the experiments and drafted the manuscript. JR, HL, and LW participated in the work to analyze the data. HL participated in the revision of the manuscript. All authors read and approved the final manuscript.
Authors’ information
Not applicable
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Ren, J., Liu, H., Xue, Y. et al. Adsorption Behavior of CH4 Gas Molecule on the MoX2(S, Se, Te) Monolayer: The DFT Study. Nanoscale Res Lett 14, 293 (2019). https://doi.org/10.1186/s11671-019-3125-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s11671-019-3125-5