Abstract
Optical waveguide cross-sectional shapes that deviate from rectangles or squares may cause significant loss of signal. In this study, a photolithography approach was adopted to fabricate waveguides on printed circuit boards, using photo-imageable polysiloxane as a waveguide material. The effects of I-line ultraviolet (UV) lamp exposure, 355-nm Nd:YAG laser direct imaging, and 248-nm excimer laser direct imaging on the cross-sectional shape of waveguides were investigated. For I-line UV lamp exposure, increasing the exposure time could cause changes in the tilt angle of the waveguides from negative (inverted trapezoid) to positive (trapezoid). To obtain rectangular waveguides, the optimum I-line UV lamp exposure time was found to be around 150 s. From the results for 355-nm Nd:YAG laser direct imaging, the width and tilt angle of the waveguides varied with the energy density of the laser beam irradiating the core materials, being controlled by the repetition rate and focus. Lowering the laser energy density could produce waveguides with small widths and tilt angles. Excimer laser direct imaging at 248 nm was found to be unsuitable for waveguide patterning since the core materials could not be cured at this wavelength.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
E. Griese, Print. Circuit Fabr. 25, 20 (2002).
H.T. Holden, Circuit World 29, 42 (2003).
S. Kopetz, E. Rabe, W.J. Kang, and A. Neyer, Electron. Lett. 40, 668 (2004).
K.B. Yoon, I.K. Cho, and S.H. Ahn, J. Lightwave Technol. 22, 2119 (2004).
H. Ma, A.K.-Y. Jen, and L.R. Dalton, Adv. Mater. 14, 1339 (2002).
R. Dangel, C. Berger, R. Beyeler, L. Dellmann, M. Gmür, R. Hamelin, F. Horst, T. Lamprecht, T. Morf, S. Oggioni, M. Spreafico, and B.J. Offrein, IEEE Trans. Adv. Packag. 31, 759 (2008).
F. Grillot, L. Vivien, S. Laval, D. Pascal, and E. Cassan, IEEE Photonics Technol. Lett. 16, 1661 (2004).
S. Kopetz, D. Cai, E. Rabe, and A. Neyer, Int. J. Electron. Commun. (AEÜ) 61, 163 (2007).
M. Immonen, J. Wu, H.J. Yan, P.-F. Chen, J.X. Xu, and T. Rapala-Virtanen, Circuit World 38, 104 (2012).
S.S. Zakariyah, P.P. Conway, D.A. Hutt, D.R. Selviah, K. Wang, J. Rygate, J. Calver, and W. Kandulski, J. Lightwave Technol. 29, 3566 (2011).
G.V. Steenberge, N. Hendrickx, E. Bosman, J.V. Erps, H. Thienpont, and P.V. Daele, IEEE Photonics Technol. Lett. 18, 1106 (2006).
S.S. Zakariyah, P.P. Conway, D.A. Hutt, K. Wang, and D.R. Selviah, Opt. Laser Eng. 50, 1752 (2012).
T. Bierhoff, Y. Sonmez, J. Schrage, A. Himmler, E. Griese, G. Mrozynski, Proceedings 6th IEEE Workshop on Signal Propagation on Interconnects (Torino, Italy: Politecnico di Torino, 2002), p. 47.
K. Tamaki, H. Takase, Y. Eriyama, and T. Ukachi, J. Photopolym. Sci. Technol. 16, 639 (2003).
LIGHTLINK™ Optical Waveguide Technology Process Manual, Dow, Rev. 3.
Technical Data Sheet of LIGHTLINK™ XP-5202A Waveguide Clad, Dow, Rev. 1.
Technical Data Sheet of LIGHTLINK™ XP-6701A Waveguide Core, Dow, Rev. 1.
M. I. Gurian, Printed Circuit Handbook, 6th ed., Chap. 34, ed. C.F. Coombs, Jr. (New York: McGraw-Hill, 2008).
Laser Drill System Application Guides-Model 5150/5200, ESI, June 1999.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yung, Kc., Lee, Cp., Wong, Ch. et al. Influence of Photolithography on the Cross-Sectional Shape of Polysiloxane as an Optical Waveguide Material on Printed Circuit Boards. J. Electron. Mater. 42, 3494–3501 (2013). https://doi.org/10.1007/s11664-013-2732-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11664-013-2732-7