Abstract
In this study, the ultraviolet (UV) curing and air pressure imprinting methods are proposed for the fabrication of a light-intensity-enhancement component. The air-pressing process provides a uniform embossing pressure, and the UV curing module enables the process to be performed at room temperature and low pressure. Because the UV resin is sensitive to the process parameters, such as the curing time and pressing pressure, the liquid resin must be filled at a precise pressure. To control the precision, the UV embossing facility comprised a resin-dispensing system, air-pressing system, and UV curing system. These systems were controlled by the Arduino system. In the Arduino system, the computer-controlled input can eliminate artificial errors and each forming step can be programed into one script to achieve automation. In this study, V-groove microstructures were formed. The V-groove pattern was replicated with a width of 47 μm and height of 22 μm on polymethyl methacrylate substrate for use as a light guiding panel. The proposed methodology enables automatic control of the UV microscale imprinting process.
Similar content being viewed by others
References
Bender M, Otto M, Hadam B et al (2000) Fabrication of nanostructures using a UV-based imprint technique. Microelectron Eng 53:233–236. https://doi.org/10.1016/S0167-9317(00)00304-X
Bender M, Otto M, Hadam B et al (2002) Multiple imprinting in UV-based nanoimprint lithography: related material issues. Microelectron Eng 61–62:407–413. https://doi.org/10.1016/S0167-9317(02)00470-7
Faugel H, Bobkov V (2013) Open source hard- and software: using Arduino boards to keep old hardware running. Fusion Eng Des 88:1276–1279. https://doi.org/10.1016/j.fusengdes.2012.12.005
Kim I, Mentone PF (2006) Electroformed nickel stamper for light guide panel in LCD back light unit. Electrochim Acta 52:1805–1809. https://doi.org/10.1016/j.electacta.2006.01.083
Kim H-H, Beom-Hoan O, Lee S-G, Park S-G (2010) Fabrication of novel double microlens using two step soft lithography. Microelectron Eng 87:1033–1036. https://doi.org/10.1016/j.mee.2009.11.099
Lee H-J, Yoon T-H, Kim D-P (2007) Fabrication of microfluidic channels derived from a UV/thermally cured preceramic polymer via a soft lithographic technique. Microelectron Eng 84:2892–2895. https://doi.org/10.1016/j.mee.2007.03.002
Li C-J, Fang Y-C, Cheng M-C (2010) Prism-pattern design of an LCD light guide plate using a neural-network optical model. Opt Int J Light Electron Opt 121:2245–2249. https://doi.org/10.1016/j.ijleo.2009.09.007
Liew L-A, Liu Y, Luo R et al (2002) Fabrication of SiCN MEMS by photopolymerization of pre-ceramic polymer. Sens Actuators Phys 95:120–134. https://doi.org/10.1016/S0924-4247(01)00723-3
Park S, Shin Y, Choi E et al (2012) Improvement of luminance and uniformity of light guide panel using scatterer pattern by laser processing. Opt Laser Technol 44:1301–1306. https://doi.org/10.1016/j.optlastec.2011.12.040
Price RBT (2017) Light curing in dentistry. Dent Clin N Am 61:751–778. https://doi.org/10.1016/j.cden.2017.06.008
Schmitt H, Rommel M, Bauer AJ et al (2010) Full wafer microlens replication by UV imprint lithography. Microelectron Eng 87:1074–1076. https://doi.org/10.1016/j.mee.2009.11.069
Shih Y-M, Kao C-C, Ke K-C, Yang S-Y (2017) Imprinting of double-sided microstructures with rapid induction heating and gas-assisted pressuring. J Micromech Microeng 27:095012. https://doi.org/10.1088/1361-6439/aa7acd
Wang Y, Zhao Q, Shang Y et al (2011) Ultra-precision machining of Fresnel microstructure on die steel using single crystal diamond tool. J Mater Process Technol 211:2152–2159. https://doi.org/10.1016/j.jmatprotec.2011.07.018
Yang J-C, Huang C-C (2013) Fabrication of dual brightness enhancement structures on light guide plates using UV roll-to-plate imprinting lithography. Opt Int J Light Electron Opt 124:3324–3328. https://doi.org/10.1016/j.ijleo.2012.10.049
Zhang XH, Que W, Jia CY et al (2011) Fabrication of micro-lens arrays built in photosensitive hybrid films by UV-cured imprinting technique. J Sol Gel Sci Technol 60:71–80. https://doi.org/10.1007/s10971-011-2552-2
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Chang, NW., Ke, KC. & Yang, SY. Fabrication of a light-intensity-enhancement component by using computer-controlled ultraviolet curing and air-pressing imprinting. Microsyst Technol 25, 31–37 (2019). https://doi.org/10.1007/s00542-018-3927-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00542-018-3927-x