Abstract
Several new random copolyethers of styrene oxide (SO) and other monosubstituted oxirane as comonomer, i.e., propylene oxide (PO), isopropyl glycidyl ether (IPGE) or allyl glycidyl ether (AGE), were synthesized in THF solution at room temperature. As initiator monopotassium salt of dipropylene glycol activated by 18-crown-6 complexing agent was used. Synthesized copolyether-diols were characterized by SEC, 13C NMR and MALDI-TOF techniques. They were unimodal and had Mn = 3500–4600 and relatively low dispersity (Mw/Mn = 1.16–1.18). Low unsaturation of the products resulted from chain transfer reaction to styrene oxide. Composition of SO/PO-diol, SO/IPGE-diol and SO/AGE-diol copolymers was determined by MALDI-TOF mass spectrometry. Homopolymers were not formed during the processes.
Graphical abstract
![](http://media.springernature.com/lw685/springer-static/image/art%3A10.1007%2Fs00289-019-02717-y/MediaObjects/289_2019_2717_Figa_HTML.png)
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
Introduction
Polyether-polyols are the most important group of polyols for synthesis of polyurethanes, which represent about 80% of the total oligo-polyols production [1, 2]. The functionality of an oligo-polyol for elastic polyurethane is 2–3 hydroxyl groups/mol. Polyether-polyols are obtained by the polymerization of oxiranes, such as ethylene oxide (EO), propylene oxide (PO) and 1,2-butylene oxide (BO). Polymerization is carried out in bulk at elevated temperature and pressure in the presence of starter/catalyst systems. The most important starters used for the synthesis of oligo-polyols for elastic polyurethanes are water, ethylene glycol, diethylene glycol, 1,2-propylene glycol, dipropylene glycol and glycerol [1]. The catalysts utilized for polymerization belong to anionic (alkali metal hydroxides) [3], cationic (Lewis acids and Brönstedt super acids) [4,5,6], coordinative groups (aluminum and zinc alkyls and alkoxides, titanium alkoxides [7,8,9] and also dimetallic catalysts (DMC) can be used [10].
The most important system used industrially for the synthesis of polyether-diols with high molar masses is KOH and 1,2-propylene glycol [1]. The second system is the group of dimetallic catalysts based on a nonstoichiometric complex of Zn3[Co(CN)6]3·ZnCl2 with various ligands [10], which are 100 times more active than KOH. The polyether-diols are used especially for polyurethane elastomers, coating adhesives and sealants [11, 12]. The most popular classes of such polymers are PPO-diols (Mn = 400–4000), block copolymers PO-EO with terminal PEO blocks (Mn = 2000–4000), block copolymers PO-EO with internal PEO block (Mn = 2000–4000) and random copolymers PO-EO (Mn = 2000–4000). 13C NMR spectra of homopolymers and block and random linear copolymers PO-EO have been studied [13, 14]. In the earlier studies [11] the monomer sequence was elucidated at the diad level. Then, triad sequence has been unequivocally indentified, including the effects of stereoisomerism [14]. The second commonly used class of polyether-polyols are the polyether-triols which are applied in flexible polyurethane foams fabrication. The majority of technologically important polyether-triols are copolymers PO-EO. Random copolymers are used in continuous slabstock flexible foams and block copolymers PO-EO with terminal PEO block used in molded foams [1]. The high Mn polyether-triols, i.e., PO-EO copolymers, being the largest part of industrial production, are synthesized by polymerization of PO and/or EO initiated by eluent [1]. To modify the properties of the polyol component, copolymers are widely synthesized using anionic ring-opening copolymerization for propylene oxide and glycidol [15, 16], propylene oxide and N,N-diethyl glycidyl amine [17], ethylene oxide and sulfonamide-activated aziridines [18] or ethylene oxide or butylene oxide with glycerol [19]. Also cationic ring-opening copolymerization can be performed [20]. In the literature, there are reports concerning performing of ROP of other oxirane-ring-based monomers like styrene oxide [21], cyclohexane oxide [22] or ethoxyethyl glycidyl ether (EEGE) and isopropylidene glyceryl glycidyl ether (IGG) [23]. It is known that homopolymerization of styrene oxide in ROP either cationic or anionic leads to low molecular mass oligomers, accompanied by higher temperature and longer polymerization time [21].
In the present work, we decided to synthesize new copolymers, i.e., random SO-oxirane copolyether-diols [where SO denotes styrene oxide and oxirane was PO, isopropyl glycidyl ether (IPGE) or allyl glycidyl ether (AGE)] and analyze their composition. The novelty of the work is the use of monopotassium salt of dipropylene glycol activated by 18-crown-6 complexing agent as initiator. Also new copolymers are synthesized, which can be interesting as substrates for synthesis of new thermoplastic polyurethanes. All reactions, i.e., synthesis of initiator and copolymerization, were carried out in tetrahydrofuran solution at room temperature and normal pressure. The products obtained were characterized by use of SEC, 13C NMR and MALDI-TOF techniques.
Experimental
Materials
Monomers, i.e., propylene oxide, styrene oxide, isopropyl glycidyl ether and allyl glycidyl ether (all from Aldrich), were dried over CaH2 and distilled at 306 K (33 °C), 467 K (194 °C), 414 K (131 °C), 427 K (154 °C), respectively. Anhydrous tetrahydrofuran (THF) (Acros Organics) was kept over CaH2 and distilled at 339 K (66 °C) prior to use. Potassium hydride (KH) (Aldrich) was purified according to the procedure described by Brown [24]. Dipropylene glycol (Aldrich) and 18-crown-6 (18C6) (Merck) and were used without purification.
Synthesis
All syntheses were carried out at room temperature in a 50 cm3 reactor equipped with a magnetic stirrer and a Teflon valve enabling substrates delivery and sampling under argon atmosphere. Monopotassium salt of dipropylene glycol was obtained in the reaction of KH with dipropylene glycol dissolved in THF. For example, potassium hydride (0.08 g, 2.0 mmol) and tetrahydrofuran (6.2 cm3) containing 18C6 (0.53 g, 2.0 mmol) were introduced into the reactor and then 0.5 mol/dm3 solution of dipropylene glycol in tetrahydrofuran (4.0 cm3) was added. The reaction mixture was then stirred during 20 min until all hydrogen (44.7 cm3) was evolved. It resulted in solution of monopotassium salt of dipropylene glycol activated by 18C6 complexing agent. That system was then used as the initiator, when the mixture of styrene oxide (4.6 cm3, 4.8 g, 40 mmol) and equimolar amount of IPGE (4.7 cm3) was introduced into the reactor and stirred to the end of copolymerization. Then, the reaction mixture was neutralized with HCl/H2O system (0.1 mol/dm3, 50 cm3) and transferred to the separator containing chloroform (70 cm3). After 5-min shaking, two layers were obtained, i.e., inferior copolyether layer and superior layer containing water and the potassium salt. These layers were separated, and the superior layer was removed. After triple washing with distilled water, copolyether was obtained by evaporating of chloroform and water in vacuum. In the next experiments SO-PO and SO-AGE copolyethers were prepared in similar way. The concentration of monomers during the polymerization was monitored by the 1,4-dioxane method [25]. The final conversion of monomers was ~ 99%, while the yields of the products were 97–99%.
Measurements
100 MHz 13C NMR spectra were recorded in CDCl3 at 25 °C on a Bruker Avance 400 pulsed spectrometer equipped with 5 mm broad band probe and applying Waltz16 decoupling sequence. Chemical shifts were referenced to tetramethylsilane serving as an internal standard. In order to obtain a good spectrum of the copolymer main chain exhibiting its microstructural details, about 3000 scans were satisfactory, but in order to observe the signals of the polymer chain ends more then 10, 000 scans were necessary. Molar masses and dispersities of copolymers were obtained by means of size exclusion chromatography (SEC) on a Shimadzu Prominance UFLC instrument at 40 °C on a Shodex 300 mm × 8 mm OHpac column using tetrahydrofuran as a solvent. Polystyrenes were used as calibration standards. Matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF) spectra were recorded on a Shimadzu AXIMA Performance instrument. The mass spectrometer operated in linear mode. The laser power was optimized to obtain a good signal-to-noise ratio after averaging 250 single-shot spectra. Dithranol was used as a matrix (10.0 mg/mL) and polymer samples were dissolved in tetrahydrofuran (2.0 mg/mL) producing clear, homogenous solutions. By using a pipette 0.5 μL of sample solution and 0.5 μL of matrix solution were applied onto a stainless-steel target plate then air dried at room temperature for several minutes. Data were acquired in continuum mode until acceptable averaged data were obtained and were analyzed using Shimadzu Biotech Launchpad program. Resolution and accuracy of the registered spectra were 1000 and 0.5, respectively. The spectrometer mass calibration was performed upon 4 calibration points derived for peptides standards within mass range between 757.40 (standard1: Bradykinin fragment 1–7, Mcalc (M + H)+ = 757.40 Da) up to 3657.93 (standard4: Adrenocorticotropic Hormone Fragment 7–38 human, Mcalc (M + H)+ = 3657.93 Da).
Results and discussion
Three new copolymers were prepared in this work by use of monopotassium salt of dipropylene glycol as initiator which was activated by macrocyclic ligand 18-crown-6 (K-DPG/L). In each experiment, SO was mixed with other oxirane as comonomer and introduced to initiator solution in tetrahydrofuran. It starts anionic ring-opening copolymerization, which results in random copolyether-diols (Scheme 1).
The role of ligand was activation of alkoxide center of growing chain by the formation of separated ion pairs and free ions. It resulted in increasing of the reactions rate and yield. The products obtained were analyzed by several techniques. SEC method indicated that all copolymers are unimodal. Their characterization is presented in Table 1.
13C NMR analysis of copolymers reveals strong signals of carbons present in polymer chains (CH2 and CH) and substituents as well as weak signals of terminal carbons. Spectrum of exemplary copolymer (1) is shown in Fig. 1. For SO/PO copolyether-diol (1) the chemical shift of signals corresponding to end group carbon (δCH(R)OH) is at 73.0, 65.0 and 67.1. The chemical shifts of respective signals for SO/IPGE copolyether-diol (2) and SO/AGE copolyether-diol (3) are at 73.0; 69.8 and 73.0; 70.1.
Additionally weak signals in unsaturated region (at 136.2 and 159.7 ppm) were found for the copolymers (1)–(3). They indicated that chain transfer with SO occurred during the propagation, observed recently by us in anionic homopolymerization of SO [26], but this reaction is strongly limited. On the other hand, similar reaction with comonomers did not take place. For example, signals at 116.7 and 134.9 ppm characteristic for allyloxy group were not observed in the spectrum of copolymer (1). It is also worth noting that in the spectra of copolymers (2) and (3) weak signal of CH3 group derived from initiator is shown at 17.3 ppm (Fig. 2). Other weak signals of terminal carbons in CH(R)OH groups derived from comonomers. It clearly indicated that propagation occurred in two directions due to cation exchange reaction (Scheme 2).
In order to determine the composition of macromolecules MALDI-TOF mass spectrometry was applied. Spectra of copolymers (1)–(3) were shown below. Each signal in the spectrum was analyzed separately. Figure 3 shows MALDI-TOF spectrum of copolymer (1). Next to the spectrum one of the possible structure of the macromolecules chains is presented, which originates from incorporation of both SO (Mmer = 120.1) and PO mers (Mmer = 58.1). The general scheme of the macromolecules composition was described as H − (PO)m1 − (SO)n1 − INI − (SO)n2 − (PO)m2 − H, where n1 ≠ n2 and m1 ≠ m2.
Several signals were observed in the spectrum at m/z 1000 to 5000. Among them there are scare signals corresponding to PSO-diols and PPO-diols homopolymers. The signal represent macromolecules containing different numbers of SO and PO mers. All macromolecules contain central part derived from initiator and form adducts with sodium ions. The main characterization data of SO/PO copolyether-diol (1) involving composition of macromolecules are presented in Table 2.
In the range of m/z 1694.3 to 3428.6, several kinds of macromolecules were identified, which contain 7 ÷ 19 mers of SO and different PO mers (9 ÷ 20), for example, macromolecules containing 10 mers of SO and 10 ÷ 16 mers of PO (no4, Table 2), macromolecules with 18 mers of SO and 10 ÷ 18 mers of PO (no12, Table 2). In general, in analyzed m/z range with increasing number of SO mers in the macromolecules chains numbers of PO mers decreased. The most abundant signals represent sodium adducts of macromolecules with following composition: SO14PO15 (no8, Table 2), SO9PO16 and SO9PO13 (no3, Table 2).
Similar results were obtained for other systems (Figs. 4, 5 and Table 4, respectively). Next to the spectrum of each copolymers, one of the possible structure of the macromolecules chains is presented, which originates from incorporation of both SO (Mmer = 120.1) and either IPGE (Mmer = 116.1) (Fig. 4) or AGE (Mmer = 114.1) (Fig. 5) mers. The general scheme of the macromolecules composition was described as H − (IPGE)m1 − (SO)n1 − INI − (SO)n2 − (IPGE)m2 − H for SO/IPGE copolyether-diol (2) and H − (AGE)m1 − (SO)n1 − INI − (SO)n2 − (AGE)m2 − H for SO/AGE copolyether-diol (3).
In the spectrum of SO/IPGE copolyether-diol (2) at m/z 1000 to 5500, no signals of homopolymers, i.e., PSO-diols or PIPGE-diols were observed. The signals represent copolyether-diols which form adducts with sodium ions. Characterization data of macromolecules describing their composition are shown in Table 3. In the range of m/z 983.4 to 5016.1, a number of macromolecules were identified, which contain 4 ÷ 17 mers of SO and 3 ÷ 17 mers of IPGE.
In general, in analyzed m/z range with increasing number of SO mers in the macromolecules chains numbers of IPGE mers decreased. For instance, macromolecules with 6 mers of SO contain 6 ÷ 12 mers of IPGE (no3, Table 3), whereas macromolecules with 17 mers of SO contain 10 ÷ 14 mers of IPGE (no14, Table 3). Signals of the most intensities represent sodium adducts of SO12IPGE13 (no9, Table 3), SO14IPGE14 (no11, Table 3) and SO15IPGE13 (no12, Table 3) macromolecules.
Several signals were shown in the spectrum of SO/AGE copolyether-diol (3) in the range of m/z from 1500 to 5500. Most signals represent copolyether-diols, which form adducts with sodium ions. Sare signals of homopolymers, i.e., PSO-diols or PAGE-diols were identified. Characterization data of macromolecules concerning their composition are shown in Table 4.
In the range of m/z 1794 to 5214.2 macromolecules containing 7 ÷ 18 mers of SO and 9 ÷ 19 mers of AGE were found. In general, with increasing number of SO mers in the macromolecules chains numbers of AGE mers decreased. For example, macromolecules with 8 mers of SO contain 10 ÷ 18 mers of AGE (no2, Table 4), whereas macromolecules with 17 mers of SO contain 11 and 13 mers of AGE (no11, Table 4). The most abundant signals represent sodium adducts of macromolecules with the following formulas SO13AGE15, SO11AGE14 and SO16AGE17.
Summarizing, styrene oxide easily polymerizes with other oxiranes, as propylene oxide, isopropyl glycidyl ether or allyl glycidyl ether giving random copolyether-diols after protonation. The product consists of macromolecules with various composition. They could be useful for synthesis of new thermoplastic polyurethanes.
Conclusions
Monopotassium salt of dipropylene glycol activated by coronand 18C6 in THF solution at room temperature effectively initiates random copolymerization of styrene oxide and propylene oxide, isopropyl glycidyl ether or allyl glycidyl ether. The main features of these processes are:
-
All synthesized copolyether-diols are unimodal and have relatively low dispersity (Mw/Mn = 1.16–1.19). This value is close to the dispersities derived for catalyzed ring-opening homopolymerization of SO (1.06–1.14) [21].
-
Mainly copolymers were synthesized in the reaction course with spare homopolymers chains formed during the studied processes.
-
Chain transfer reaction with monomer occurs exclusively for styrene oxide, leading to very low unsaturation.
-
Propagation occurs in two directions due to cation exchange reaction.
-
MALDI-TOF technique allows to determine composition of copolyether-diols obtained; exemplary SO/AGE system contain several macromolecules with 7–18 mers of SO and 9–19 mers of AGE; in general, with increasing number of SO mers in the macromolecules chains numbers of AGE mers decreased.
-
The products obtained could be interesting as substrates for synthesis of new thermoplastic polyurethanes.
References
Ionescu M (2008) Chemistry and technology of polyols for polyurethanes. Rapra Technol Ltd, Shawbury
Wegener G, Brandt M, Duda L, Hofmann J, Klesczewski B, Koch D et al (2001) Trends in industrial catalysis in the polyurethane industry. Appl Catal A 221:303–335. https://doi.org/10.1016/S0926-860X(01)00910-3
Bruins PF (1969) Polyurethane technology. Interscience Publishers, New York
Kubisa P, Penczek S (1999) Cationic activated monomer polymerization of heterocyclic monomers. Prog Polym Sci 24:1409–1437. https://doi.org/10.1016/S0079-6700(99)00028-3
Penczek S, Kubisa P (1993) In: Brunelle DJ (ed) Ring-opening polymerization. Mechanisms, catalysis, structure, utility. Hanser Publishers, Münich
Penczek S, Sekiguchi H, Kubisa P (1997) In: Hatada K, Kitayama T, Vogl O (eds) Macromolecular design of polymeric materials. Marcel Dekker, New York
Aida T, Inoue S (1981) Living polymerization of epoxide catalyzed by the porphyrin-chlorodiethylaluminium system. Structure of the living end. Macromolecules 14:1166–1169. https://doi.org/10.1021/ma50006a005
Inoue S, Aida T (1992) New method for polymer synthesis. In: Mijs WJ (ed) Plenum Press, New York, p 33
Sugimoto H, Inoue S (1999) Polymerization by metalloporphyrin and related complexes. Adv Polym Sci 146:39–119. https://doi.org/10.1007/3-540-49424-3_2
Schuchardt J, Harper S (1989) In: Proceedings of the 32nd annual polyurethane technical marketing conference, San Francisco, p 360
Lamba NMK, Woodhouse KA, Cooper SL (1998) Polyurethanes in biomedical applications. CRC Press, New York
Meier-Westhues U (2007) Polyurethanes-coatings, adhesives and sealants. Vincentz Network Gmbh, Hannover
Whipple EB, Green PJ (1973) Sequence analysis of ethylene oxide-propylene oxide copolymers by carbon-13 nuclear magnetic resonance. Macromolecules 6:38–40. https://doi.org/10.1021/ma60031a006
Heatley F, Luo Y-Z, Ding J-F, Mobbs RH, Booth C (1988) A carbon-13 nuclear magnetic resonance study of the triad sequence structure of block and statistical copolymers of ethylene oxide and propylene oxide. Macromolecules 21:2713–2721. https://doi.org/10.1021/ma00187a011
Schömer M, Seiwert J, Frey H (2012) Hyperbranched poly(propylene oxide): a multifunctional backbone-thermoresponsive polyether polyol copolymer. CS Macro Lett 1:888–891. https://doi.org/10.1021/mz300256y
Sunder A, Mullhaupt R, Frey H (2000) Hyperbranched polyether-polyols based on polyglycerol: polarity design by block copolymerization with propylene oxide. Macromolecules 33:309–314. https://doi.org/10.1021/ma991191x
Blankenburg J, Wagner M, Frey H (2017) Well-defined multi-amino-functional and stimuli-responsive poly(propylene oxide) by Crown Ether assisted anionic ring-opening polymerization. Macromolecules 50:8885–8893. https://doi.org/10.1021/acs.macromol.7b01324
Gleede T, Rieger E, Blankenburg J, Klein K, Wurm FR (2018) Fast access to amphiphilic multiblock architectures by the anionic copolymerization of aziridines and ethylene oxide. J Am Chem Soc 140:13407–13412. https://doi.org/10.1021/jacs.8b08054
Scharfenberg M, Seiwert J, Scherger M, Preis J, Susewind M, Frey H (2017) Multiarm polycarbonate star polymers with a hyperbranched polyether core from CO2 and common epoxides. Macromolecules 50:6577–6585. https://doi.org/10.1021/acs.macromol.7b01131
Christ EM, Hobernik D, Bros M, Wagner M, Frey H (2015) Cationic copolymerization of 3,3-bis(hydroxymethyl)oxetane and glycidol: biocompatible hyperbranched polyether polyols with high content of primary hydroxyl groups. Biomacromol 16(10):3297–3307. https://doi.org/10.1021/acs.biomac.5b00951
Misaka H, Sakai R, Satoh T, Kakuchi T (2011) Synthesis of high molecular weight and end-functionalized poly(styrene oxide) by living ring-opening polymerization of styrene oxide using the alcohol/phosphazene base initiating system. Macromolecules 44:9099–9107. https://doi.org/10.1021/ma202115w
Su ChK, Chuang HJ, Li ChY, Yu ChY, Ko BT, Chen JD, Chen MJ (2014) Oxo-bridged bimetallic group 4 complexes bearing amine-bis(benzotriazole phenolate) derivatives as bifunctional catalysts for ring-opening polymerization of lactide and copolymerization of carbon dioxide with cyclohexene oxide. Organometallics 33(24):7091–7100. https://doi.org/10.1021/om500784a
Hofmann AM, Wurm F, Frey H (2011) Rapid access to polyfunctional lipids with complex architecture via oxyanionic ring-opening polymerization. Macromolecules 44(12):4648–4657. https://doi.org/10.1021/ma200367c
Brown CA (1974) Saline hydrides and superbases in organic reactions. VII. Potassium hydride, highly active new hydride reagent. Reactivity, applications, and techniques in organic and organometallic reactions. J Org Chem 39:3913–3928. https://doi.org/10.1021/jo00940a025
Siggia S (1963) Quantitative organic analysis via functional groups. Wiley, New York, p 241
Grobelny Z, Matlengiewicz M, Jurek-Suliga J, Golba S, Skrzeczyna K, Kwapulińska D (2017) Ring opening polymerization of styrene oxide initiated with potassium alkoxides and hydroxyalkoxides activated by 18-crown-6: determination of mechanism and preparation of new polyether-polyols. Polym Bull 74:4763–4780. https://doi.org/10.1007/s00289-017-1976-4/
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
The authors declare that there is no known conflict of interest concerning the given work.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Grobelny, Z., Jurek-Suliga, J., Golba, S. et al. Anionic ring-opening copolymerization of styrene oxide with monosubstituted oxiranes: analysis of composition of prepared new copolyether-diols by MALDI-TOF mass spectrometry. Polym. Bull. 76, 6291–6303 (2019). https://doi.org/10.1007/s00289-019-02717-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00289-019-02717-y