Abstract
A 3-D computational fluid dynamics (CFD) model was developed to simulate the friction stir welding of 6-mm plates of DH36 steel in an Eulerian steady-state framework. The viscosity of steel plate was represented as a non-Newtonian fluid using a flow stress function. The PCBN-WRe hybrid tool was modelled in a fully sticking condition with the cooling system effectively represented as a negative heat flux. The model predicted the temperature distribution in the stirred zone (SZ) for six welding speeds including low, intermediate and high welding speeds. The results showed higher asymmetry in temperature for high welding speeds. Thermocouple data for the high welding speed sample showed good agreement with the CFD model result. The CFD model results were also validated and compared against previous work carried out on the same steel grade. The CFD model also predicted defects such as wormholes and voids which occurred mainly on the advancing side and are originated due to the local pressure distribution between the advancing and retreating sides. These defects were found to be mainly coming from the lack in material flow which resulted from a stagnant zone formation especially at high traverse speeds. Shear stress on the tool surface was found to increase with increasing tool traverse speed. To produce a “sound” weld, the model showed that the welding speed should remain between 100 and 350 mm/min. Moreover, to prevent local melting, the maximum tool’s rotational speed should not exceed 550 RPM.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Xiaocong H, Fengshou G, Andrew B (2014) A review of numerical analysis of friction stir welding. Prog Mater Sci 65:1–66
Nandan R, Roy GG, Lienert TJ, Debroy T (2007) Three-dimensional heat and material flow during friction stir welding of mild steel. Acta Mater 55(3):883–895
Toumpis AI, Gallawi A, Arbaoui L, Poletz N (2014) Thermo-mechanical deformation behaviour of DH36 steel during friction stir welding by experimental validation and modelling. Sci Technol Weld Join 19(8):653–663
Micallef D, Camilleri D, Toumpis A, Galloway A, & Arbaoui L (2015) Local heat generation and material flow in friction stir welding of mild steel assemblies. J Materials: Design and Applications, 0(0)(0), 1–17
Enkhsaikhan B, Edward C (2009) Detecting wormholes in friction stir welds from welding feedback data, Midwest instruction and computing symposium. South Dakota, USA
Toumpis A, Gallawi A, Cater S, McPherson N (2014) Development of a process envelope for friction stir welding of DH36 steel—a step change. Mater Des 62:64–75
Stevenson R, Toumpis A, Galloway A (2015) Defect tolerance of friction stir welds in DH36 steel. Material and design 87:701–711
Toumpis AI, Gallawi A, Molter L, Polezhayeva H (2015) Systematic investigation of the fatigue performance of a friction stir welded low alloy steel. Mater Des 80:116–128
Lenard J, Pietrzyk M, Cser L (1999) Mathematical and physical simulation of the properties of hot rolled products. Elsevier, Amsterdam, pp 1–10
Megastir (2013) Friction Stir Welding of high melting temperature materials .Online resource
Endo R, Shima M, Susa M (2010) Thermal-conductivity measurements and predictions for Ni–Cr solid solution alloys. Int J Thermophys 31:1991–2003
Atharifar H, Lin D, Kovacevic R (2009) Numerical and experimental investigations on the loads carried by the tool during friction stir welding. J Mater Eng Perform 18(4):339–350
Jacquin D, de Meester B, Simar A, Deloison D, Montheillet F, Desrayaud C (2011) A simple Eulerian thermomechanical modeling of friction stir welding. J Mater Process Technol 211(1):57–65
Grujicic M, Arakere G, Yalavarth HV, He CF, Yen C-F, Cheeseman BA (2010) Modeling of AA5083 material-microstructure evolution during butt friction-stir welding. J Mater Eng Perform 19(5):672–684
Schmidt H (2004) Hattel J and wert J,2004, an analytical model for the heat generation in friction stir welding. Modelling Simul Mater Sci Eng 12:143–157
Cox C, Lammlein D, Strauss A, Cook G (2010) Modeling the control of an elevated tool temperature and the affects on axial force during friction stir welding. Mater Manuf Process 25:1278–1282
Hasan AF, Bennett CJ, Shipway PH (2015) A numerical comparison of the flow behaviour in friction stir welding (FSW) using unworn and worn tool geometries. Mater Des 87:1037–1046
Al-moussawi M, Smith AJ, Young A, Cater S and Faraji M (2016) An advanced numerical model of friction stir welding of DH36 steel, 11th Int. Symp. FSW, TWI Granta Park Cambridge, UK
Cho H, Kimd D, Hong S, Jeong Y, Lee K, Cho Y, Kang S, Han H (2015) Three-dimensional numerical model considering phase transformation in friction stir welding of steel. Metall Mater Trans A 46A:6040–6051
Arora A, Nandan R, Reynold AP, DebRoya T (2009) Torque, power requirement and stir zone geometry in friction stir welding through modelling and experiments. Scr Mater 60(1):13–16
Darvazi AR, Iranmanesh M (2014) Thermal modeling of friction stir welding of stainless steel 304 L. Int J Adv Manuf Technol 75(9–12):1299–1307
Pal S, Phaniraj MP (2015) Determination of heat partition between tool and workpiece during FSW of SS304 using 3D CFD modelling. J Mater Process Technol 222:280–286
Bergman TL, Incropera FP, DeWitt David P, Lavine AS (2011) Fundamentals of heat and mass transfer, 7th E edn. John Wiley and sons, USA
Khandkar MZH, Khan JA, Reynolds AP (2003) Prediction of temperature distribution and thermal history during friction stir welding: input torque based model. Sci Technol Weld Join 8(3):165–174
Long T, Tang W, Reynolds AP (2007) Process response parameter relationships in aluminium alloy friction stir welds. Sci Technol Weld Join 12(4):311–317
Elbanhawy A, Chevallier E, Domin K (2013) Numerical investigation of friction stir welding of high temperature materials. NAFEMS world congress, Salzburg
Besharati-Givi MK and Asadi P (2014) Advances in friction-stir welding and processing, a volume in woodhead publishing series in welding and other joining technologies, ScienceDirect
Fehrenbacher A, Schmale JR, Zinn MR, Pfefferkorn FE (2014) Measurement of tool-workpiece Interface temperature distribution in friction stir welding. J Manuf Sci Eng 136(2):21009
Yang KY, Dong H, Kou S (2008) Liquation tendency and liquid-film formation in friction stir spot welding. Weld J 87:202–211
Colegrove P, Shercliff (2005) 3-dimensional CFD modelling of flow round a threaded friction stir welding tool profile, H. J Mater Process Technol 169:320–327
Smith AJ, AL-Moussawi M, Young AE, Cater S and Faraji M (2016). Modelling of friction stir welding of 304 stainless steel. In: European Simulation and Modelling Conference, Univ. of Las Palmas, 26-28th October 2016
Leonard ES (1999) Light microscopy of carbon steel, ASM International ©, USA
Wang H, Colegrove PA, dos Santos J (2013) Hybrid modelling of 7449-T7 aluminium alloy friction stir welded joints. Sci Technol Weld Join 18:147–153
Fairchild D, Kumar A , Ford S, Nissley N (2009) Research concerning the friction stir welding of linepipe steels, Trends in welding research, Proceedings of the 8th International Conference, pp371–380
Nandan R, Lienert TJ, Debroy T (2008) Toward reliable calculations of heat and plastic flow during friction stir welding of Ti-6Al-4 V alloy. Int J Mat Res 99(4):434–444
Morisada Y, Fujii H, Kawahito Y, Nakata K, Tanaka M (2011) 2011, three-dimensional visualization of material flow during friction stir welding by two pairs of X-ray transmission systems. Scr Mater 65:1085–1088
Schmidt HNB, Dickerson TL, Hattel JH (2006) Material flow in butt friction stir welds in AA2024-T3. Acta Mater 54:1199–1209
Morisada Y et al (2014) Three-dimensional visualization of material flow during friction stir welding of steel and aluminum. J Mater Eng Perform 23(11):4143–4147
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Al-moussawi, M., Smith, A.J., Young, A. et al. Modelling of friction stir welding of DH36 steel. Int J Adv Manuf Technol 92, 341–360 (2017). https://doi.org/10.1007/s00170-017-0147-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0147-y