Abstract
This chapter introduces various construction automation concepts that have been developed over the past few decades and presents examples of construction robots that are in current use (as of 2006) and/or in various stages of research and development. Section 47.1 presents an overview of the construction industry, which includes descriptions of the industry, the types of construction, and the typical construction project. The industry overview also discusses the concept of automation versus robotics in construction and breaks down the concept of robotics in construction into several levels of autonomy. Section 47.1 also presents traditional and advanced concepts for sensing systems in construction, which enable the use of robots and various forms of automation. Section 47.2 discusses some of the economic aspects of implementing robotics in construction, and Sect. 47.3 presents examples of robots from various construction applications. Section 47.4 discusses unsolved technical problems in construction robotics, which include interoperability, connection systems, tolerances, and power and communications. Finally, Sect. 47.5 discusses future directions in construction robotics and Sect. 47.6 gives some conclusions and suggests resources for further reading.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
Abbreviations
- ATLSS:
-
advanced technology for large structural systems
- CAD:
-
computer-aided design
- CNC:
-
computer numerical control
- EDM:
-
electrical discharge machining
- EDM:
-
electronic distance measuring
- GDP:
-
gross domestic product
- GPR:
-
ground-penetrating radar
- GPS:
-
global positioning system
- I3CON:
-
industrialized, integrated, intelligent, construction
- LADAR:
-
laser radar or laser detection and ranging
- LIDAR:
-
light detection and ranging
- LOS:
-
line of sight
- MEMS:
-
microelectromechanical systems
- RAM:
-
random-access (volatile) memory
- RF:
-
radiofrequency
- RFID:
-
radiofrequency identification
- RGB:
-
red, green, blue
- ROM:
-
read-only memory
- US:
-
ultrasound
- UWB:
-
ultra-wideband
- iGPS:
-
indoor GPS
References
E. Ginzberg: The mechanization of work, Sci. Am. 247(3), 66–75 (1982)
US Bureau of the Census: Value of Construction Put in Place – Seasonally Adjusted Annual Rate (Luscensus, Washington 2006), available at: http://www.census.gov/
Bureau of Labor Statistic: Industry at a Glance, NAICS 23: Construction (US Department of Labor, Washington 2006), available at: http://www.bls. gov/iag/construction.htm
US Bureau of the Census: Statistics of U.S. Businesses (Luscensus, Washington 2006), available at: http://www.census.gov/csd/susb/
European Communities: Europe in Figures – Eurostat Yearbook 2005 (European Commission, Brussels, 2005), available at: http://epp.eurostat.ec. europa .eu/cache/ITY_OFFPUB/KS-CD-05-001/EN/KS-CD-05-001-EN.PDF
D. Crosthwaite: The global construction market: a cross-sectional analysis, Constr. Man. Econ. 18(5), 619–627 (2000)
D.W. Halpin, R.W. Woodhead: Construction Management, 2nd edn. (Wiley, New York 1998)
K.S. Saidi: Possible Applications of Handheld Computers to Quantity Surveying, Diss. (The Univ. Texas, Austin 2002)
Eurostat: European Business – Facts and Figures (European Commission, Brussels 2007), , available at: http://epp.eurostat.ec.europa.eu/pls/portal/url/page/PGP_MISCELLANEOUS/PGE_DOC_DETAIL?p_product_code= KS-BW-06-001
T. Greaves, B. Jenkins: Capturing Existing Conditions with Terrestrial Laser Scanning: a Report on Opportunities, Challenges and Best Practices for Owners, Operators, Engineering/Construction Contractors and Surveyors of Built Assets and Civil Infrastructure (Spar Point Research, Danvers 2004)
L. Cousineau, N. Miura: Construction Robots: the Search for New Building Technology in Japan (ASCE, Reston 1998)
J.G. Everett, H. Saito: Construction automation: demands and satisfiers in the United States and Japan, J. Constr. Eng. Man. ASCE 122(2), 147–151 (1996)
M. Taylor, S. Wamuziri, I. Smith: Automated construction in Japan, Proc. Inst. Civil Eng. Civil Eng. 156(1), 34–41 (2003)
J. Maeda: Current research and development and approach to future automated construction in Japan, Proc. Congress Construction Research Congress (2005) p. 2403
C. Balaguer, M. Abderrahim, J.M. Navarro, S. Boudjabeur, P. Aromaa, K. Kahkonen, S. Slavenburg, D. Seward, T. Bock, R. Wing, B. Atkin: FutureHome: an integrated construction automation approach, IEEE Robot. Autom. Mag. 9(1), 55–66 (2002)
Y. Maruyama, Y. Iwase, K. Koga, J. Yagi, H. Takada, N. Sunaga, S. Nishigaki, T. Ito, K. Tamaki: Development of virtual and real-field construction management systems in innovative, intelligent field factory, Autom. Constr. 9(5-6), 503–514 (2000)
C. Balaguer: Soft robotics concept in construction industry, World Automation Congress (2004) pp. 517–522
K.A. Reed: The Role of the CIMSteel Integration Standards in Automating the Erection and Surveying of Structural Steelwork, 19th Int. Symp. Autom. Robot. Constr. SP989 (NIST, Gaithersburg, 2002)
N.J. Shih: The application of a 3-D scanner in the representation of building construction site, ISARC 2002: 19th Int. Symp. Autom. Robot. Constr. (2002) pp. 337–342
B. Akinci, F. Boukamp, C. Gordon, D. Huber, C. Lyons, K. Park: A Formalism for utilization of sensor systems and integrated project models for active construction quality control, Autom. Constr. 15(2), 124–138 (2006)
G.S. Cheok, W.C. Stone: Non-intrusive scanning technology for construction assessment, IAARC/IFAC/IEEE. Int. Symp. (1999) pp. 645–650
K. McKinney, M. Fischer: Generating, evaluating and visualizing construction schedules with CAD tools, Autom. Constr. 7(6), 433–447 (1998)
B. Akinci, M. Fischer, J. Kunz: Automated generation of work spaces required by construction activities, J. Constr. Eng. Manage. ASCE 128(4), 306–315 (2002)
V. Kamat, R. Lipman: Evaluation of standard product models for supporting automated erection of structural steelwork, Autom. Constr. 16(2), 232–241 (2006)
C.M. Eastman: Building Product Models (CRC, Boca Raton 1999)
M. Vega, T. Bock, A. Malone: Newsletter 3 (ManuBuild Open Building Manufacturing, Moorgate 2006), available at: http://www.manubuild. org/
G. Aouad, J. Kirkham, P. Brandon, F. Brown, G. Cooper, S. Ford, R. Oxman, M. Sarshar, B. Young: Information modeling in the construction industry – the information engineering approach, Constr. Manage. Econ. 11(5), 384–397 (1993)
G. Beer: Tunconstruct: a new european initiative, Tunnels Tunneling Int. FEV (2006) pp. 21–23
H.M. Huang: Autonomy Levels for Unmanned Systems (ALFUS) Framework Volume I: Terminology Version 1.1, NIST SP1011 (NIST, Gaithersbrg 2004), available at: http://www.isd.mel.nist.gov/projects/autonomy _levels/publications/NISTSP_1011_ver_1.1.pdf
Y.F. Ho, H. Masuda, H. Oda, L.W. Stark: Distributed control for tele-operations, IEEE/ASME Trans. Mechatron. 5(2), 100–109 (2000)
S. Singh: State of the art in automation of earthmoving, ASCE J. Aerosp. Eng. 10(4), 179–188 (2002)
H. Quang, M. Santos, N. Quang, D. Rye, H. Durrant-Whyte: Robotic excavation in construction automation, IEEE Robot. Autom. Mag. 9(1), 20–28 (2002)
J. Albus, R. Bostelman, N. Dagalakis: The NIST RoboCrane, J. Robot. Syst. 10(5), 709–724 (1993)
K.S. Saidi, A.M. Lytle, W.C. Stone, N.A. Scott: Developments toward automated construction (NIST Interagency Rep., 7264 2005)
S.C. Kang, E. Miranda: Physics based model for simulating the dynamics of tower cranes, 10th Int. Conf. Comput. Civil Building Eng. (ICCCBE) (Weimar 2004)
C. Lindfors, P. Chang, W. Stone: Survey of construction metrology options for AEC industry, J. Aerosp. Eng. 12, 58 (1999)
S. Kang, D. Tesar: A Novel 6-DoF measurement tool with indoor GPS for metrology and calibration of modular reconfigurable robots, IEEE ICM Int. Conf. Mechatron. (Istanbul 2004)
L.E. Bernold, L. Venkatesan, S. Suvarna: Equipment mounted multi-sensory system to locate pipes, Pipelines 130, 112 (2004)
D.A. Willett, K.C. Mahboub, F. PE, B. Rister: Accuracy of ground-penetrating radar for pavement-layer thickness analysis, J. Transp. Eng. 132, 96 (2006)
C.L. Barnes, J.F. Trottier: Effectiveness of ground penetrating radar in predicting deck repair quantities, J. Infrastruct. Syst. 10, 69 (2004)
J.A. Huisman, S.S. Hubbard, J.D. Redman, A.P. Annan: Measuring soil water content with ground penetrating radar – a review, Vadose Zone J. 2(4), 476–491 (2003)
G.W. Housner, L.A. Bergman, T.K. Caughey, A.G. Chassiakos, R.O. Claus, S.F. Masri, R.E. Skelton, T.T. Soong, B.F. Spencer, J.T.P. Yao: Structural control: past, present, and future, J. Eng. Mech. 123(9), 897–971 (1997)
United States Department of Transportation: Maturity Meters: A Concrete Success, ed. by L. Pope (Federal Highway Administration (FHWA), Washington 2002)
S.V. Ramaiah, B.F. McCullough, T. Dossey: Estimating in Situ Strength of Concrete Pavements Under Various Field Conditions (The Univ. of Texas, Austin 2001) Center Transport. Res.
J. Song, C. Haas, C. Caldas, E. Ergen, B. Akinci, C.R. Wood, J. Wadephul: Field Trials of RFID Technology for Tracking Fabricated Pipe – Phase II (FIATECH, Austin 2003), available at: http://www.fiatech.org
J. Song, C.T. Haas, C. Caldas, E. Ergen, B. Akinci: Automating the task of tracking the delivery and receipt of fabricated pipe spools in industrial projects, Autom. Constr. 15(2), 166–177 (2006)
J. Aksoy, I. Chan, K. Guidry, J. Jones, C.R. Wood: Materials and Asset Tracking Using RFID: A Preparatory Field Pilot Study (FIATECH, Austin 2004), available at: http://www.fiatech.org
J. Kang, P. Woods, J. Nam, C.R. Wood: Field Tests of RFID Technology for Construction Tool Management (FIATECH, Austin 2005), available at: http://www.fiatech.org
J.B. OʼBrien: Holistic automation of construction projects, 13th Int. Symp. Autom. Robot. Constr. (1996) pp. 179–188
F. Peyret, J. Jurasz, A. Carrel, E. Zekri, B. Gorham: The computer integrated road construction project, Autom. Constr. 9(5), 447–461 (2000)
J.B. OʼBrien: Robotics as a technology for risk reduction in construction work, First Annual Risk Engineering Seminar – Implementation of Performance based risk and safety standards (1996) pp. 60–72
R.H. Hayes, S.C. Wheelwright: Restoring Our Competitive Edge: Competing Through Manufacturing (Wiley, New York 1984)
Y. Miyatake: SMART system: A full-scale implementation of computer integrated construction, 10th Int. Symp. Autom. Robot. Constr. (Houston 1993)
A.M. Lytle, K.S. Saidi: NIST research in autonomous construction, Auton. Robots 22(3), 211–221 (2007)
J.G. Everett, A.H. Slocum: Automation and robotics opportunities – construction versus manufacturing, J. Constr. Eng. Manage. ASCE 120(2), 443–451 (1994)
L.A. Demsetz: Task identification for construction automation, 6th Int. Symp. Autom. Robot. Constr. (1989) pp. 95–102
R. Kangari, D.W. Halpin: Potential robotics utilization in construction, J. Constr. Eng. Manage. 115(1), 126–143 (1989)
R.L. Tucker: High payoff areas for automation applications, 6th Int. Symp. Autom. Robot. Constr. (1988) pp. 9–16
F. Peyret: The Achievements of the computer integrated road construction project, 17th IAARC/CIB/ IEEE/IFAC/IFR Int. Symp. Autom. Robot. Constr. (ISARC) (Taipei 2000)
Commonwealth Scientific, Industrial Research Organisation: Mining Robotics Project (CSIRO, Clayton South 2006), available at: http://www.csiro.au/ csiro/content/ standard/ps1kk.html
D.A. Bradley, D.W. Seward: The development, control and operation of an autonomous robotic excavator, J. Intell. Robot. Syst. 21(1), 73–97 (1998)
Pacific Coal, C. Hughes: Project C8001: Introduction of Autonomous Haul Trucks. Final Report (Australian Coal Research, Brisbane 1997)
K. Kikuchi, S. Furuta, T. Imai: Development and the result of practical works of concrete floor finishing robot, 5th Int. Symp. Autom. Robot. Constr. (1988)
K. Arai, B. Yamada, M. Saito, K. Banno: The development and practice test of the Mark II mobile robot for concrete floor slab finishing, 5th Int. Symp. Autom. Robot. Constr. (1988)
H. Benckert: Mechydronic for boom control on truck-mounted concrete pumps, Tech. Symp. Constr. Equipment Technol. 2003 (Dresden 2003)
E. Gambao, C. Balaguer, F. Gebhart: Robot assembly system for computer-integrated construction, Autom. Constr. 9(5-6), 479–487 (2000)
K.S. Saidi, A.M. Lytle, W.C. Stone, N.A. Scott, N.A. Scott: Developments toward automated construction (NIST Interagency Rep. 7264, 2005)
Y. Miyatake, Y. Yamazaki, R. Kangari: The SMART system project: a strategy for the management of information and automation technology in computer Integrated Construction. In: Management of Information Technology for Construction, ed. by S. Marthur Krishan (Worls Scientific, Brighton 1993) pp. 407–420
C. Haas, K. Saidi, Y. Cho, W. Fagerlund, H. Kim, Y. Kim: Implementation of an Automated Road Maintenance Machine (ARMM) (Univ. of Texas, Austin 1999) Center for Transportation Research, Project Summary Report
D.A. Bennett, X. Feng, S.A.V.A. Maintenance, C. Technology: AHMCT Automated crack sealing program and the operator controlled crack sealing machine, Transportation Res. Board 2003 Annual Meeting (2003)
C. Balaguer, A. Gimenez, J.M. Pastor, V.M. Padron, M. Abderrahim: A climbing autonomous robot for inspection applications in 3-D complex environments, Robotica 18(03), 287–297 (2000)
S.J. Lorenc, B.E. Handlon, L.E. Bernold: Development of a robotic bridge maintenance system, Autom. Constr. 9(3), 251–258 (2000)
M.P. Gallaher, R.E. Chapman: Cost Analysis of Inadequate Interoperability in the US Capital Facilities Industry (National Institute of Standards and Technology, Gaithersburg 2004) US Dept. of Commerce, Technology Administration
K.B. Lee, M.E. Reichardt: Open standards for homeland security sensor networks, Instrum. Meas. Mag. IEEE 8(5), 14–21 (2005)
E.F. Begley, M.E. Palmer, K.A. Reed: Semantic mapping between IAI ifcXML and FIATECH AEX models for centrifugal pumps (National Institute of Standards and Technology, Gaithersburg, 2005)
R. Fleischman, B.V. Viscomi, L.W. Lu: Development, analysis and experimentation of ATLSS connections for automated construction. Proceedings of the 1st World Conference on Steel Structures (Acapulco 1992)
S. Garrido, M. Abderrahim, A. Gimenez, C. Balaguer: Anti-swinging input shaping control of an automatic construction crane, IEEE Trans. Autom. Sci. Eng. (2007)
J.K. Latta: Inaccuracies in Construction (National Research Council Canada, Ottawa 1975), available at: http://irc.nrc-cnrc.gc.ca/pubs/cbd/cbd171_e.html
A.M. Lytle, K.S. Saidi: Application of laser-based 3-D imaging to steel construction, ISARG (2006)
A.M. Lytle, K.S. Saidi: Proceedings of the Automated Steel Construction Workshop June 6-7, 2002 (National Institute of Standards and Technology, Gaithersburg 2004), NIST Internal Report 7108
Author information
Authors and Affiliations
Corresponding authors
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2008 Springer-Verlag
About this entry
Cite this entry
Saidi, K.S., OʼBrien, J.B., Lytle, A.M. (2008). Robotics in Construction. In: Siciliano, B., Khatib, O. (eds) Springer Handbook of Robotics. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-540-30301-5_48
Download citation
DOI: https://doi.org/10.1007/978-3-540-30301-5_48
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-540-23957-4
Online ISBN: 978-3-540-30301-5
eBook Packages: EngineeringEngineering (R0)