Friction Stir Processing of Aluminum Alloy A206: Part I—Microstructure Evolution Ning SunDiran Apelian OriginalPaper 03 October 2018 Pages: 234 - 243
Friction Stir Processing of Aluminum Alloy A206: Part II—Tensile and Fatigue Properties Ning SunWayne J. JonesDiran Apelian OriginalPaper 03 October 2018 Pages: 244 - 254
Effect of Pouring Conditions and Gating System Design on Air Entrainment During Mold Filling Seyyed Hojjat MajidiChristoph Beckermann OriginalPaper 23 October 2018 Pages: 255 - 272
Thermal Analysis of Rare Earth Grain Refined 4130 Robert TuttleHet A. Kapadia OriginalPaper 08 November 2018 Pages: 273 - 285
Understanding the Role of Inclusions on the Dynamic Fracture Toughness of High Strength Lightweight FeMnAl Steels R. Vaz PennaL. N. BartlettT. Constance OriginalPaper 13 November 2018 Pages: 286 - 299
Effect of Alloy Composition on Microstructure and Tensile Properties of Net-Shaped Castings of Al–Zn–Mg–Cu Alloys Reza GhiaasiaanSumanth Shankar OriginalPaper 20 August 2018 Pages: 300 - 310
A Comparative Study on Titanium-Reinforced Aluminium Matrix Composites Produced by Melt Infiltration Casting and Squeeze Infiltration Ridvan GecuAhmet Karaaslan OriginalPaper 23 August 2018 Pages: 311 - 319
Revealing the As-Cast and Homogenized Microstructures of Niobium-Bearing Nickel-Based Superalloy Mohammad Javad SohrabiHamed MirzadehMohsen Rafiei OriginalPaper 23 August 2018 Pages: 320 - 330
Effect of Ce Inoculation on Microstructure and Mechanical Properties of in situ Al–20%Mg2Si Composite Yingmin LiTongyu LiuYuyan Ren OriginalPaper 27 August 2018 Pages: 331 - 336
Optimizing Morphology of Primary Carbides and Mechanical Properties during Processing of Cast-Cold Work AISI D2-Steel Press Forming Dies S. A. ElghazalyK. GyulaW. Elghazaly OriginalPaper 28 August 2018 Pages: 337 - 344
Parameter Optimization of Gas Tungsten-Arc Repair Welding Technique in Mg–6Gd–3Y–0.5Zr Alloy D. H. MengB. ZhouP. J. Li OriginalPaper 28 August 2018 Pages: 345 - 353
Optimisation of Dry Sliding Wear Parameters of Squeeze Cast AA336 Aluminium Alloy: Copper-Coated Steel Wire-Reinforced Composites by Response Surface Methodology Samson Jerold Samuel ChelladuraiRamesh ArthanariSiva Rama Chandran Petchimuthu OriginalPaper 03 September 2018 Pages: 354 - 366
Modification of Hypereutectic Al–20 wt%Si Alloy Based on the Addition of Yttrium and Al–5Ti–1B Modifiers Mixing Melt Qinglin LiBinqiang LiTiandong Xia OriginalPaper 07 September 2018 Pages: 367 - 383
Microstructure and Mechanical Properties of an AlN/Mg–Al Composite Synthesized by Al–AlN Master Alloy Zengqiang LiTong GaoXiangfa Liu OriginalPaper 10 September 2018 Pages: 384 - 391
Characterization and Microhardness Evaluation of A356/Mg Joint Produced by Vacuum-Assisted Sand Mold Compound Casting Process Rajender Kumar TayalSudhir KumarRohit Garg OriginalPaper 20 September 2018 Pages: 392 - 406
Influences of Rod Diameter and Sand-Mould Strength on Hot Tearing in Mg WE43A Constrained Rod Castings Qing Ya SunDong-Rong LiuEr Jun Guo OriginalPaper 20 September 2018 Pages: 407 - 416
Effects of Different Parameters on Porosity Defects Between the Horizontal and Vertical Shot Sleeve Processes Dashan SuiQingyou Han OriginalPaper 28 September 2018 Pages: 417 - 425
Effects of Al–Ti–C–Ce Master Alloy on Microstructure and Mechanical Properties of Hypoeutectic Al–7%Si Alloy Wanwu DingXiaoyan ZhaoTiandong Xia OriginalPaper 28 September 2018 Pages: 426 - 437
Effects of Amplitude of Die Vibration on Cast Structure of Al4.5Cu Alloy Meet C. MehtaDurbadal MandalSujoy K. Chaudhury OriginalPaper 08 October 2018 Pages: 438 - 449
Quality Index of Tensile Properties on Microporosity Variation in A5052 Aluminium Alloy SunKi KimChoongDo LeeYoungJig Kim OriginalPaper 02 November 2018 Pages: 450 - 462
Reducing Shrinkage Porosity in High-Performance Steel Castings: Case of an ASME B16.34 Gate Valve Body: Part 2—Simulation and Experimental Verification Nawaz MahomedHendrik Andries Kleynhans OriginalPaper 02 November 2018 Pages: 463 - 472
Phase Evolution of β-Al5FeSi During Recycling of Al–Si–Fe Alloys by Mg Melt Tong GaoZengqiang LiXiangfa Liu OriginalPaper 07 November 2018 Pages: 473 - 478