Light Metals Alliance: Light Metals Technology 2017 Special Section News 10 May 2018 Pages: 427 - 427
The Role of Zn Additions on the Microstructure and Mechanical Properties of Mg–Nd–Zn Alloys S. GavrasT. SubrotoD. Tolnai OriginalPaper 18 September 2017 Pages: 428 - 433
Effect of Co and Ni Addition on the Microstructure and Mechanical Properties at Room and Elevated Temperature of an Al–7%Si Alloy Toni BogdanoffArne K. DahleSalem Seifeddine OriginalPaper Open access 02 October 2017 Pages: 434 - 440
Complexities in the Assessment of Melt Quality Martin RiestraAnton BjurenstedtSalem Seifeddine OriginalPaper Open access 12 October 2017 Pages: 441 - 448
Effect of Cooling Rate on the Mechanical Properties of AA365 Aluminum Alloy Heat-Treated Under T4, T5, and T6 Conditions Eunkyung LeeBrajendra Mishra OriginalPaper 28 November 2017 Pages: 449 - 456
Effect of Titanium Levels on the Hot Tearing Sensitivity and Abnormal Grain Growth After T4 Heat Treatment of Al–Zn–Mg–Cu Alloys Xiaochun ZengCassandra FergusonSumanth Shankar OriginalPaper 10 April 2018 Pages: 457 - 468
Dimensional Control of Nickel-Based Single Crystal Turbine Blade Investment Casting by Process Control Optimization Fei QiuKun BuXian-Dong Zhang OriginalPaper 13 October 2017 Pages: 469 - 479
Effect of Silicon and Microstructure on Spheroidal Graphite Cast Iron Thermal Conductivity at Elevated Temperatures Kalle JalavaKaisu SoivioJuhani Orkas OriginalPaper 20 October 2017 Pages: 480 - 486
Effect of Process Parameters on Distortion and Residual Stress of High-Pressure Die-Cast AZ91D Components Hoda DiniNils-Eric AnderssonAnders E. W. Jarfors OriginalPaper Open access 01 November 2017 Pages: 487 - 497
Experimental Investigation and Optimization of Process Parameters for Impact Strength of Compound Cast Bimetallic Joints Rajender Kumar TayalSudhir KumarVikram Singh OriginalPaper 13 November 2017 Pages: 498 - 513
Simulation of Fluidity and Misrun Prediction for the Casting of 356.0 Aluminum Alloy into Sand Molds V. E. BazhenovA. V. PetrovaA. V. Koltygin OriginalPaper 13 November 2017 Pages: 514 - 522
Microstructure and Tribological Characteristics of Strain-Induced Melt Activation (SIMA)-Processed Al–10Cu–Fe alloy L. Sankara RaoA. K. JhaS. N. Ojha OriginalPaper 13 November 2017 Pages: 523 - 542
Effects of Process Related Variations on Fillablity Simulation of Thin-Walled IN718 Structures Mohsin RazaRoger SvenningssonAnders E. W. Jarfors OriginalPaper Open access 20 November 2017 Pages: 543 - 553
Effect of Samarium (Sm) Addition on the Microstructure and Tensile Properties of Al–20%Si Casting Alloy Qinglin LiJinbao LiTiandong Xia OriginalPaper 21 November 2017 Pages: 554 - 564
Effects of Electromagnetic Frequency and SiC Nanoparticles on the Microstructure Refinement and Mechanical Properties of Al A357-1.5 wt% SiC Nanocomposites Reza Mohammadi BadiziMohsen Askari-PaykaniHamid Reza Shahverdi OriginalPaper 01 December 2017 Pages: 565 - 573
Effects of Addition of Transition Metals on Intermetallic Precipitation in Al–2%Cu–1%Si-Based Alloys A. I. IbrahimE. M. ElgalladF. H. Samuel OriginalPaper 04 December 2017 Pages: 574 - 588
Effect of Degassing and Grain Refinement on Hot Tearing Tendency in Al8Si3Cu Alloy Muhammet UludağRemzi ÇetinMurat Tiryakioğlu OriginalPaper 06 December 2017 Pages: 589 - 595
Counter-Gravity Sand Casting of Steel with Pressurization During Solidification Lucas ArcherRichard A. HardinChristoph Beckermann OriginalPaper 12 December 2017 Pages: 596 - 606
Effect of Ca on the Y Content and Cyclic Oxidation Behavior of Ni-Based Single-Crystal Superalloy Genfeng ShangPengzhe GaoHang Wang OriginalPaper 14 December 2017 Pages: 607 - 613
AlSi5Mg0.3 Alloy for the Manufacture of Automotive Wheels M. KabaA. DonmezY. Birol OriginalPaper 19 December 2017 Pages: 614 - 624
Inclusion Measurements in Al–Si Foundry Alloys Using Qualiflash and Prefil Filtration Techniques A. M. SamuelH. W. DotyF. H. Samuel OriginalPaper 20 November 2017 Pages: 625 - 642
Metallurgical Aspects of Inclusion Assessment in Al–6%Si Casting Alloy Using the LiMCA Technique A. M. SamuelH. W. DotyF. H. Samuel OriginalPaper 20 December 2017 Pages: 643 - 657