Notch wear detection in cutting tools using gradient approach and polynomial fitting H. H. ShahabiT. H. LowM. M. Ratnam ORIGINAL ARTICLE 05 March 2008 Pages: 1057 - 1066
Influence of friction during forming processes—a study using a numerical simulation technique Pradeep L. MenezesK. KumarSatish V. Kailas ORIGINAL ARTICLE 29 February 2008 Pages: 1067 - 1076
The effect of die/blank holder and punch radiuses on limit drawing ratio in angular deep-drawing dies Cebeli ÖzekMuhammet Bal ORIGINAL ARTICLE 13 March 2008 Pages: 1077 - 1083
On the temperature field during superficial grinding: an experimental study A. Aguiar VieiraA. Monteiro BaptistaR. M. Natal Jorge ORIGINAL ARTICLE 05 April 2008 Pages: 1084 - 1092
Influence of electrical conditions on performance of electrical discharge machining with powder suspended in working oil for titanium carbide deposition process Katsushi FurutaniHiromichi SatoMasayuki Suzuki ORIGINAL ARTICLE 21 February 2008 Pages: 1093 - 1101
Optimisation of multiple responses for WEDM processes using weighted principal components Susanta Kumar GauriShankar Chakraborty ORIGINAL ARTICLE 26 February 2008 Pages: 1102 - 1110
Design and experimental study of a power supply for micro-wire EDM Mu-Tian YanTsung-Liang Chiang ORIGINAL ARTICLE 06 March 2008 Pages: 1111 - 1117
A hybridized approach to optimal tolerance synthesis of clutch assembly Erwie ZaharaYi-Tung Kao ORIGINAL ARTICLE 19 February 2008 Pages: 1118 - 1124
An intelligent sampling method for inspecting free-form surfaces Suleiman M. ObeidatShivakumar Raman ORIGINAL ARTICLE 18 March 2008 Pages: 1125 - 1136
Model for surface-roughness parameters determination in a virtual machine shop environment N. BilalisM. PetousisA. Antoniadis ORIGINAL ARTICLE 15 March 2008 Pages: 1137 - 1147
In-cycle monitoring of tool nose wear and surface roughness of turned parts using machine vision H. H. ShahabiM. M. Ratnam ORIGINAL ARTICLE 04 March 2008 Pages: 1148 - 1157
A novel depth-from-focus-based measurement system for the reconstruction of surface morphology with depth discontinuity Gyung Bum KimGui Yun Tian ORIGINAL ARTICLE 14 March 2008 Pages: 1158 - 1165
Roughness modeling and optimization in CNC end milling using response surface method: effect of workpiece material variation B. C. RoutaraA. BandyopadhyayP. Sahoo ORIGINAL ARTICLE 15 March 2008 Pages: 1166 - 1180
Study on LD-VHDL conversion for FPGA-based PLC implementation Daoshan DuYadong LiuMakoto Fujishima ORIGINAL ARTICLE 28 February 2008 Pages: 1181 - 1190
Feedrate scheduling strategy for free-form surface machining through an integrated geometric and mechanistic model Liqiang ZhangJingchun FengMing Chen ORIGINAL ARTICLE 13 March 2008 Pages: 1191 - 1201
A bicriteria parallel machine scheduling with a learning effect Tamer ErenErtan Güner ORIGINAL ARTICLE 07 March 2008 Pages: 1202 - 1205
A study of lead time variation impact on supply chain performance Jafar HeydariReza Baradaran KazemzadehS. Kamal Chaharsooghi ORIGINAL ARTICLE 23 February 2008 Pages: 1206 - 1215
Bicriteria scheduling of a two-machine flowshop with sequence-dependent setup times S. Afshin MansouriS. Hamed HendizadehNasser Salmasi ORIGINAL ARTICLE 19 March 2008 Pages: 1216 - 1226
An artificial neural network approach to multiple-response optimization R. NoorossanaSam Davanloo TajbakhshA. Saghaei ORIGINAL ARTICLE Open access 03 April 2008 Pages: 1227 - 1238
A comprehensive study on the free vibration of machine tools’ hexapod table M. MahboubkhahM. J. NateghS. Esmaeilzadeh Khadem ORIGINAL ARTICLE 07 March 2008 Pages: 1239 - 1251
A band-type network model for the time-series problem used for IC leadframe dam-bar shearing process Zone-Ching LinDar-Yuan Chang ORIGINAL ARTICLE 18 March 2008 Pages: 1252 - 1266
