Investigation of Microstructure, Mechanical Properties and Residual Stress in Non-equal-Channel Angular Pressing of 6061 Aluminum Alloy H. KhanlariM. Honarpisheh Original Article 31 March 2020 Pages: 1109 - 1121
Influence of Sintered Low-Alloy Steel Microstructure on the DLC Coating Characteristics Mahsa Haji GhasemiBehrooz GhasemiHamid Reza Mohammadian Semnani Original Article 02 April 2020 Pages: 1123 - 1130
Optimization Study on Sliding Wear Characteristics and Heat-Treatment Conditions of Different Grades of Ferritic Ductile Cast Iron V. BramarambaS. Sen Original Article 04 April 2020 Pages: 1131 - 1146
Mechanical and Thermoelectric Properties of Eutectic Composite (Bi, Sb)2Te3/Te Thermoelectric Material Femi Emmanuel OluSoon-Jik HongKamanio Chattopadhyay Original Article 09 April 2020 Pages: 1147 - 1155
Effect of Ti Powders Addition on Mechanical and Metallurgical Properties of IN718/BNi-2/316L Diffusion Couple M. SalmaliyanM. Shamanian Original Article 15 April 2020 Pages: 1157 - 1169
Influence of Milling Parameters on Surface Roughness of Al–SiC–B4C Composites M. Bhuvanesh KumarR. ParameshwaranS. M. Senthil Original Article 16 April 2020 Pages: 1171 - 1183
Microstructure Evolution and Mechanical Behaviour of SAW Weldments of CSEF Steel on Preheating and PWHT Saurav SumanPankaj BiswasAvinish Tiwari Original Article 16 April 2020 Pages: 1185 - 1197
Interface and Strength of Laser Impact Welding of Fe-Based Nanocrystalline Alloys to Aluminum Xiao WangXiaojun WangHuixia Liu Original Article 19 April 2020 Pages: 1199 - 1207
Thermodynamics and Kinetics of Borochromized Coatings Prepared on 5CrNiMo Steel by Thermo-Reactive Diffusion Chenggang PanXiaolong HePeng He Original Article 22 April 2020 Pages: 1209 - 1214
Experimental Investigations on the Effect of Severe Plastic Deformation Through End Milling on X-Ray Peak Broadening and Microcrystalline Characteristics of Nimonic 263 S. GowthamanT. Jagadeesha Original Article 22 April 2020 Pages: 1215 - 1226
Effect of Reversible Cyclic Plastic Deformation and Thermal Treatment on the Microstructure and Mechanical Properties of SS304L Steel Ranveer SinghS. SharmaS. K. Vajpai Original Article 27 April 2020 Pages: 1227 - 1237
Recycling of White Aluminium Dross: Production of Potash Alum Arunabh MeshramDivyansh GautamKamalesh Kumar Singh Original Article 29 April 2020 Pages: 1239 - 1248
Characterization of Tantalum Oxide Sol–Gel-coated AZ91 Mg Alloys Canser GülSevda AlbayrakHanifi Çinici Original Article 29 April 2020 Pages: 1249 - 1256
Laboratory-Scale Tests for the Utilization of High Ash Non-Coking coal in Coke-Making Process Shaik SaidaSanchita ChakravatyKoushik Chakravarty Original Article 30 April 2020 Pages: 1257 - 1263
Influence of Feeding Techniques in Bottom Tapping Stir Casting Process for Fabrication of Alumina Nano-filler-reinforced Aluminium Composites S. PrakashR. SasikumarB. Suresha Original Article 02 May 2020 Pages: 1265 - 1272
The Effects of Cr and Zr Additives on the Microstructure and Mechanical Properties of A356 Alloy Tansel TunçayDursun ÖzyürekSüleyman Tekeli Original Article 05 May 2020 Pages: 1273 - 1285
Neuro-Fuzzy Technique for Micro-hardness Evaluation of Explosive Welded Joints Bir Bahadur SherpaPal Dinesh KumarSachin Tyagi Original Article 06 May 2020 Pages: 1287 - 1299
The Effect of Lamellar and Globular α-Phase on Mechanical Behavior of Strongly Textured Ti–6Al–4V alloy Peyman AhmadianMaryam Morakabati Original Article 06 May 2020 Pages: 1301 - 1309
Metallurgical Failure Investigation of Replaceable Tooth Flank Used in Gear Rim Applications R. SahooT. K. Sahoo Original Article 07 May 2020 Pages: 1311 - 1317
Multicomponent Diffusion Studies in Selected High Temperature for IN718/BNi-2/316L Diffusion Couple M. SalmaliyanM. ShamanianA. Shafyei Original Article 08 May 2020 Pages: 1319 - 1331
Influence of Filler Wires to Suppress the Microsegregation and to Improve Mechanical Properties of Conventional Arc-Welded Nickel-Based Superalloy Incoloy 20 M. NateshM. Manikandan Original Article 12 May 2020 Pages: 1333 - 1362
Elastic Moduli of Nanoglasses and Melt-Spun Metallic Glasses by Ultrasonic Time-of-Flight Measurements W. ArnoldR. BirringerS. P. Singh Original Article Open access 13 May 2020 Pages: 1363 - 1371
Evaluation of Mechanical Properties of Titanium Alloy after Thermal Oxidation Process Anil KumarManoj Kumar KushwahaRakesh Kumar Original Article 15 May 2020 Pages: 1373 - 1381
Sintering Process of Cu–28Zn Brass Alloy: Statistical Investigation Arman HasaniMaziyar AzadbehMahmoud Moradi Original Article 17 May 2020 Pages: 1383 - 1400
Adhesively Bonded Aluminum Double-Strap Joints Improved by Nano-silica B. PaygozarM. A. Saeimi Sadigh Original Article 18 May 2020 Pages: 1401 - 1406
