1. Control and measurement of doctoring angle at deformed state in doctoring apparatus for printed electronics

   • Sung Woong Jeon
   • Cheol Kim
   • Chung Hwan Kim

   Regular Paper 09 May 2017 Pages: 633 - 639

2. Processing errors in an on-machine measurement method based on the adaptive triangular mesh

   • Wu Shi
   • Mei-wen Zhu
   • Yang Lin

   Regular Paper 09 May 2017 Pages: 641 - 650

3. Precision measurement of Z-slide vertical error motion of an ultra-precision lathe by using three-probe method

   • Zengyuan Niu
   • Yuan-Liu Chen
   • Chun Hong Park

   Regular Paper 09 May 2017 Pages: 651 - 660

4. Increasing payload capacity of wearable robots employing linear actuators and elastic mechanism

   • Junghoon Choo
   • Jong Hyeon Park

   Regular Paper 09 May 2017 Pages: 661 - 671

5. Improving performance of cable robots by adaptively changing minimum tension in cables

   • Saeed Abdolshah
   • Giulio Rosati

   Regular Paper 09 May 2017 Pages: 673 - 680

6. Development of real-time gait phase detection system for a lower extremity exoskeleton robot

   • Dong-Hwan Lim
   • Wan-Soo Kim
   • Chang-Soo Han

   Regular Paper 09 May 2017 Pages: 681 - 687

7. Deviation calculation and analysis of tooth surfaces of conjugate-curve gear drive

   • Dong Liang
   • Bingkui Chen
   • Ruijin Liao

   Regular Paper 09 May 2017 Pages: 689 - 696

8. Effect of vibration transmission direction in ultrasonic thermoforming on the formability of micro-corrugations

   • Hojin Bae
   • Hyun-Joong Lee
   • Keun Park

   Regular Paper 09 May 2017 Pages: 697 - 703

9. Fracture behavior of adhesive interface at TDCB aluminum foam specimen with the type of Mode III

   • Jung Ho Lee
   • Jae Ung Cho

   Regular Paper 09 May 2017 Pages: 705 - 710

10. Path smoothing for five-axis machine tools using dual quaternion approximation with dominant points

    • Xin Zhao
    • Huan Zhao
    • Han Ding

    Regular Paper 09 May 2017 Pages: 711 - 720

11. Study on the design parameters of a low speed coupling of a wind turbine

    • Jong-Hun Kang
    • Hyoung-Woo Lee

    Regular Paper 09 May 2017 Pages: 721 - 727

12. Structural analysis of automotive cowl parts considering welding residual stress

    • Hee-Seon Bang
    • Chang-Soo Park
    • Han-Sur Bang

    Regular Paper 09 May 2017 Pages: 729 - 737

13. Analysis of temporal firing patterns of primary afferent C-fibers for different sensations in mice

    • Kyeongwon Cho
    • Jun Ho Jang
    • Dong Pyo Jang

    Regular Paper 09 May 2017 Pages: 739 - 745

14. Dielectrophoretic sensitivity analysis of cell characterization

    • Hyun-Boo Lee
    • Minjoong Jeong
    • Jae-Hyun Chung

    Regular Paper 09 May 2017 Pages: 747 - 754

15. 3D multi-nozzle system with dual drives highly potential for 3D complex scaffolds with multi-biomaterials

    • Zhichao Chen
    • Xianglin Zhang
    • Changqing Liu

    Regular Paper 09 May 2017 Pages: 755 - 761

16. Temperature-dependent mechanical properties of ABS parts fabricated by fused deposition modeling and vapor smoothing

    • Sung-Uk Zhang
    • Jonghyeuk Han
    • Hyun-Wook Kang

    Regular Paper 09 May 2017 Pages: 763 - 769

17. Electronic part obsolescence forecasting based on time series modeling

    • Jungmok Ma
    • Namhun Kim

    Regular Paper 09 May 2017 Pages: 771 - 777

18. Effect of substrate bias on the tribological behavior of ta-C coating prepared by filtered cathodic vacuum arc

    • Yeoh Chin Ean
    • Young-Jun Jang
    • Seock-Sam Kim

    Regular Paper 09 May 2017 Pages: 779 - 784