Volume 4, Issue 2

Search all International Journal of Material Forming articles

June 2011

Material models for sheet metal forming

Issue Editors:

Ton Boogaard,
Timo Meinders,
Han Huetink

16 articles in this issue

Thematic issue: material models for sheet metal forming
Ton van den Boogaard
Timo Meinders
Han Huétink
Editorial Open access 18 June 2011 Pages: 83 - 83
The Vegter Lite material model: simplifying advanced material modelling
Henk Vegter
Carel ten Horn
Michael Abspoel
Thematic 16 November 2010 Pages: 85 - 92
Constitutive modeling of two phase materials using the mean field method for homogenization
E. Semih Perdahcıoğlu
Hubert J. M. Geijselaers
Thematic Open access 25 November 2010 Pages: 93 - 102
On the identification of kinematic hardening material parameters for accurate springback predictions
Per-Anders Eggertsen
Kjell Mattiasson
Thematic Issue: Twente 22 December 2010 Pages: 103 - 120
Inverse method for identification of initial yield locus of sheet metals utilizing inhomogeneous deformation fields
Alper Güner
Qing Yin
A. Erman Tekkaya
Thematic Issue: Twente 23 December 2010 Pages: 121 - 128
Simulation of stretch forming with intermediate heat treatments of aircraft skins
Srihari Kurukuri
Alexis Miroux
Ton van den Boogaard
Thematic Issue: Twente Open access 23 December 2010 Pages: 129 - 140
Phenomenological modeling of anisotropy induced by evolution of the dislocation structure on the macroscopic and microscopic scale
Till Clausmeyer
Ton van den Boogaard
Swantje Bargmann
Thematic Issue: Twente Open access 06 January 2011 Pages: 141 - 154
Effect of warm forming conditions on AZ31B flow behaviour and microstructural characteristics
Daniele Pellegrini
Andrea Ghiotti
Stefania Bruschi
Thematic Issue: Twente 08 January 2011 Pages: 155 - 161
Modelling of ductile failure in aluminium sheet forming simulation
Holger Aretz
Stefan Keller
Olaf Engler
Thematic Issue: Twente 14 January 2011 Pages: 163 - 182
Variation of deep drawing steel grades’ properties in dependency of the stress state and its impact on FEA
Vera Goedel
Marion Merklein
Thematic Issue: Twente 14 January 2011 Pages: 183 - 192
Measurement and analysis of differential work hardening behavior of pure titanium sheet using spline function
Mantaro Ishiki
Toshihiko Kuwabara
Yasuhiro Hayashida
Thematic Issue: Twente 21 January 2011 Pages: 193 - 204
Phenomenological and crystal plasticity approaches to describe the mechanical behaviour of Ti6Al4V titanium alloy
Walid Hammami
Gaëtan Gilles
Laurent Duchêne
Thematic Issue: Twente 12 February 2011 Pages: 205 - 215
A new anisotropic elasto-plastic model with degradation of elastic modulus for accurate springback simulations
Marko Vrh
Miroslav Halilovič
Boris Štok
Thematic Issue: Twente 19 February 2011 Pages: 217 - 225
Evaluation of constitutive models for textured aluminium alloys using plane-strain tension and shear tests
Dasharatha Achani
Odd-Geir Lademo
Odd Sture Hopperstad
Thematic Issue: Twente Open access 05 March 2011 Pages: 227 - 241
Modelling direction-dependent hardening in magnesium sheet forming simulations
Dirk Steglich
Wolfgang Brocks
Frederic Barlat
Thematic Issue: Twente 09 March 2011 Pages: 243 - 253
On the influence of kinematic hardening on plastic anisotropy in the context of finite strain plasticity
Ivaylo N. Vladimirov
Michael P. Pietryga
Stefanie Reese
Thematic Issue: Twente 22 March 2011 Pages: 255 - 267

Volume 4, Issue 2

Search

Navigation