1. IJMF 10th anniversary - advances in material forming

   • Francisco Chinesta

   Editorial 01 September 2020 Pages: 661 - 661

2. Exploiting data in smart factories: real-time state estimation and model improvement in metal forming mass production

   • Jos Havinga
   • Pranab K. Mandal
   • Ton van den Boogaard

   IJMF 10th Anniversary - Advances in Material Forming Open access 24 July 2019 Pages: 663 - 673

   

3. Advanced modeling and simulation of sheet moulding compound (SMC) processes

   • M. Perez
   • D. Prono
   • F. Chinesta

   IJMF 10th Anniversary - Advances in Material Forming 27 August 2019 Pages: 675 - 685

   

4. Investigation of Portevin-Le Châtelier effect during Erichsen test

   • L. Z. Mansouri
   • J. Coër
   • P. Y. Manach

   IJMF 10th Anniversary - Advances in Material Forming 12 September 2019 Pages: 687 - 697

   

5. Metallurgical and material properties correlations between machined and severely plastic deformed aluminium alloy

   • Stano Imbrogno
   • Domenico Umbrello
   • Eric Segebade

   IJMF 10th Anniversary - Advances in Material Forming 12 November 2019 Pages: 699 - 708

   

6. Experimental characterization of the compressive mechanical behaviour of Ti6Al4V alloy at constant strain rates over the full elastoplastic range

   • Víctor Tuninetti
   • Paulo Flores
   • Anne-Marie Habraken

   IJMF 10th Anniversary - Advances in Material Forming 06 March 2020 Pages: 709 - 724

   

7. Surface and mechanical characterization of stationary shoulder friction stir welded lap joints: experimental and numerical approach

   • Gianluca Buffa
   • Livan Fratini
   • Antonino Squillace

   IJMF 10th Anniversary - Advances in Material Forming 07 July 2020 Pages: 725 - 736

   

8. A novel sensitivity analysis on friction spot joining process performed on aluminum\polycarbonate sheets by simulation

   • Giuseppe Serratore
   • Francesco Gagliardi
   • Francisco Chinesta

   IJMF 10th Anniversary - Advances in Material Forming Open access 15 July 2020 Pages: 737 - 747

   

9. Advances in anisotropy of plastic behaviour and formability of sheet metals

   • Dorel Banabic
   • Frédéric Barlat
   • Toshihiko Kuwabara

   IJMF 10th Anniversary - Advances in Material Forming 24 August 2020 Pages: 749 - 787

   

10. A state of the art review of hydroforming technology

    • Colin Bell
    • Jonathan Corney
    • David Savings

    Review Open access 18 December 2019 Pages: 789 - 828

    

11. Prediction of metal sheet forming based on a geometrical model approach

    • Pascal Froitzheim
    • Michael Stoltmann
    • Wilko Flügge

    Review 20 December 2019 Pages: 829 - 839

    

12. Optimized and validated prediction of plastic yielding supported by cruciform experiments and crystal plasticity

    • Holger Hippke
    • Sebastian Hirsiger
    • Pavel Hora

    Review 10 June 2020 Pages: 841 - 852

    

13. Comment on “Prediction of strain distribution and four, six, or eight ears depending on single-crystal orientation using a new single crystal criterion”

    • Frédéric Barlat

    Letter to Editor 22 July 2020 Pages: 853 - 854

    

14. Response to the letter to editor

    • Nitin Chandola
    • Oana Cazacu
    • Benoit Revil-Baudard

    Letter to Editor 17 August 2020 Pages: 855 - 860