Abstract
This study deals with the occurrence and numerical prediction of Portevin-Le Châtelier (PLC) instabilities during a forming process at room temperature. In a first part, the mechanical behavior of an aluminium alloy (5000 series) thin sheet is investigated in tension and simple shear under quasi-static conditions and at room temperature. As PLC effect takes place, jerky flow and bands of localised deformation, observed by digital image correlation, are clearly evidenced. A forming process, consisting of the mechanical bulging of a blank clamped between a die and a blank-holder with a hemispherical punch (Erichsen test), is then performed, using in-situ observation of the localised deformation bands and their propagation. In a second part, material parameters of McCormick’s model are identified considering both tensile and simple shear tests. Moreover, Hill’48 yield criterion is used to represent the material anisotropy. Finally, the numerical simulation of the Erichsen test is performed with McCormick’s model and the comparison of the load and band propagation with experiments shows a good prediction of plastic instabilities during a forming test.
Similar content being viewed by others
References
Benallal A, Berstad T, Børvik T, Hopperstad OS, Koutiri I, Nogueira De Codes R (2008) An experimental and numerical investigation of the behaviour of aa5083 aluminium alloy in presence of the portevin–le chatelier effect. Int J Plast 24(10): 1916–1945
Andreau O, Gubicza J, Zhang NX, Huang Y, Jenei P, Langdon TG (2014) Effect of short-term annealing on the microstructures and flow properties of an Al–1% Mg alloy processed by high-pressure torsion. Mater Sci Eng: A 615:231–239
Coër J, Manach PY, Laurent H, Oliveira MC, Menezes LF (2013) Piobert–Lüders plateau and Portevin–Le Chatelier effect in an Al–Mg alloy in simple shear. Mech Res Commun 48:1–7
Le Cam J-B, Robin E, Leotoing L, Guines D (2017) Calorimetric analysis of Portevin-Le Chatelier bands under equibiaxial loading conditions in Al–Mg alloys: kinematics and mechanical dissipation. Mech Mater 105:80–88
Fu S, Gao Y, Cai Y, Cheng T, Zhang Q, Wu X (2015) Study on the out-of-plane deformation of the Portevin–Le Châtelier band by using digital shearography. Measurement 72:61–67
Min J, Hector LG, Carsley JE , Stoughton TB , Carlson BE, Lin J (2015) Spatio-temporal characteristics of plastic instability in AA5182-O during biaxial deformation. Mater Des 83:786–794
Romhanji E, Popovic M, Glisic D, Stefanovic M, Milovanovic M (2004) On the Al-Mg alloy sheets for automotive application: problems and solutions. Metalurgija-J Metallur 10:205–215
Hong S, Shin SY, Lee J, Ahn D-H, Kim HS, Kim S-K, Chin K-G, Lee S (2014) Serration phenomena occurring during tensile tests of three high-manganese twinning-induced plasticity (TWIP) steels. Metall Mater Trans A 45(2):633–646
Kim JG, Hong S, Anjabin N, Park BH, Kim SK, Chin K-G, Lee S, Kim HS (2015) Dynamic strain aging of twinning-induced plasticity (TWIP) steel in tensile testing and deep drawing. Mater Sci Eng: A 633:136–143
Belotteau J, Berdin C, Forest S, Parrot A, Prioul C (2009) Mechanical behavior and crack tip plasticity of a strain aging sensitive steel. Mater Sci Eng: A 526(1):156–165
Hopperstad OS, Børvik T, Berstad T, Lademo OG, Benallal A (2007) A numerical study on the influence of the portevin–le chatelier effect on necking in an aluminium alloy. Modell Simul Mater Sci Eng 15(7):747
Mansouri LZ, Thuillier S, Manach PY (2016) Thermo-mechanical modeling of portevin-le châtelier instabilities under various loading paths. Int J Mech Sci 115–116:676–688
Coër J, Bernard C, Laurent H, Andrade-Campos A, Thuillier S (2011) The effect of temperature on anisotropy properties of an aluminium alloy. Exp Mech 51(7):1185–1195
Yoshida T, Katayama T, Usuda M (1995) Forming-limit analysis of hemispherical-punch stretching using the three-dimensional finite-element method. J Mater Process Technol 50:226–237
Gavrus A, Banu M, Ragneau E, Maier C (2010) An inverse analysis of the Erichsen test applied for the automatic identification of sheet materials behavior. Engineering 02(07):471– 476
Harpell ET, Worswick MJ, Fin M, Jain M, Martin P (2000) Numerical prediction of the limiting draw ratio for aluminum alloy sheet. J Mater Process Technol 100:131–141
McCormick PG (1988) Theory of flow localisation due to dynamic strain ageing. Acta Metall 36(12):3061–3067
Zhang S, McCormick PG, Estrin Y (2001) The morphology of portevin–le chatelier bands: finite element simulation for al–mg–si. Acta Mater 49(6):1087–1094
Manach PY, Thuillier S, Yoon J W, Coër J, Laurent H (2014) Kinematics of Portevin–Le Chatelier bands in simple shear. Int J Plast 58:66–83
Chaboche JL (2008) A review of some plasticity and viscoplasticity constitutive theories. Int J Plast 24:1642–1693
Thuillier S, Manach PY (2009) Comparison of the work-hardening of metallic sheets using tensile and shear strain paths. Int J Plast 25(5):733–751
Acknowledgements
This work was funded by the Région Bretagne (France), the Portuguese Foundation for Science and Technology via the project PTDC/EME-TME/103350/2008 and by FEDER via the programme FCOMP-01-0124-FEDER-010301.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interests
the authors declare that they have no conflict of interest.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Mansouri, L.Z., Coër, J., Thuillier, S. et al. Investigation of Portevin-Le Châtelier effect during Erichsen test. Int J Mater Form 13, 687–697 (2020). https://doi.org/10.1007/s12289-019-01511-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12289-019-01511-5