Synthesis of roller screws V. V. MorozovA. V. ZhdanovA. B. Kosterin OriginalPaper 23 October 2016 Pages: 703 - 707
Plates in hydraulic presses with ohmic heaters E. N. MalyginS. V. KarpushkinS. V. Karpov OriginalPaper 23 October 2016 Pages: 708 - 712
Automated machining of turbine blades V. A. PoletaevE. V. Tsvetkov OriginalPaper 23 October 2016 Pages: 713 - 716
Vibrational machining with torsional spindle vibrations A. Ya. RyzvanovichV. A. GeneralovV. V. Kapralov OriginalPaper 23 October 2016 Pages: 717 - 721
Stress and strain concentration in weld-joint flaws K. P. ManzhulaA. Yu. Shlepetinskii OriginalPaper 23 October 2016 Pages: 722 - 726
Thermal distribution in the PTFE–steel frictional pair E. B. SedakovaYu. P. Kozyrev OriginalPaper 23 October 2016 Pages: 727 - 730
Burnishing with wear-resistant mineral–ceramic and hard-alloy indenters V. N. GadalovA. E. GvozdevS. V. Kovalev OriginalPaper 23 October 2016 Pages: 731 - 734
Dynamic stability of band saw machines L. V. KremlevaV. I. MalyginN. V. Lobanov OriginalPaper 23 October 2016 Pages: 735 - 740
Behavior of heat-resistant alloys and titanium alloys on cutting G. D. PetukhovV. F. Makarov OriginalPaper 23 October 2016 Pages: 741 - 744
Automated production system for reagents used in water and wastewater processing E. N. ArakcheevV. E. BrunmanA. P. Petkova OriginalPaper 23 October 2016 Pages: 745 - 750
Automated 3D modeling of working turbine blades A. I. Ryazanov OriginalPaper 23 October 2016 Pages: 751 - 754
Automated management of manufacturing orders K. S. Kul’ga OriginalPaper 23 October 2016 Pages: 755 - 759
Improving tool life and machining precision in band saws A. E. Litvinov OriginalPaper 23 October 2016 Pages: 760 - 761
Precision and efficiency of metal-cutting machines V. V. BushuevA. P. KuznetsovV. V. Molodtsov OriginalPaper 23 October 2016 Pages: 762 - 773
Control loops of a supply servo drive V. V. BushuevS. V. EvstafievaV. V. Molodtsov OriginalPaper 23 October 2016 Pages: 774 - 780
Recursive model of the blunting of an abrasive grain D. V. Ardashev OriginalPaper 23 October 2016 Pages: 781 - 783
Parametric modeling of ball end mills E. A. RyabovS. Yu. YurasovO. I. Yurasova OriginalPaper 23 October 2016 Pages: 784 - 785
Influence of the wire EDM conditions on the cut width T. R. AblyazR. V. Lesnikov OriginalPaper 23 October 2016 Pages: 786 - 787
Optimizing the high-speed drilling of small-diameter holes by core flat drills Yu. I. MyasnikovD. Yu. Pimenov OriginalPaper 23 October 2016 Pages: 788 - 790
Reliability in gear shaping V. A. GrechishnikovR. M. KhusainovR. R. Khaziev OriginalPaper 23 October 2016 Pages: 791 - 795