Thermodynamic considerations of " solid state engines" based on thermoelastic martensitic transformations and the shape memory effect H. C. TongC. M. Wayman OriginalPaper Pages: 29 - 32
Solidification rate in rapid conduction cooling Paul H. ShinguRyohei Ozaki OriginalPaper Pages: 33 - 37
Fatigue behavior of maraging steel 300 L. F. Van SwamR. M. PellouxN. J. Grant OriginalPaper Pages: 45 - 54
The densities of high-purity iron-carbon alloys in the spheroidized condition F. X. KayserA. LitwinchukG. L. Stowe OriginalPaper Pages: 55 - 58
The non-cubic lattice of rapidly quenched packet martensite A. K. SachdevP. G. Winchell OriginalPaper Pages: 59 - 63
Deformation kinetics of the Ti-6Al-4V alloy at low temperatures B. de MeesterM. DönerH. Conrad OriginalPaper Pages: 65 - 75
The grain size dependence of flow and fracture in a Cr-Mn-N austenitic steel from 300 to 1300K V. Kutumba RaoD. M. R. TaplinP. Rama Rao OriginalPaper Pages: 77 - 86
The effect of surface dissolution on fatigue crack nucleation in polycrystalline copper H. MasudaD. J. Duquette OriginalPaper Pages: 87 - 94
Transformational elasticity in a polycrystalline Cu-Zn-Sn alloy I. DvorakE. B. Hawbolt OriginalPaper Pages: 95 - 99
Effects of transient carbon deposition on the sodium sulfate-induced corrosion of nickel-base alloys D. W. McKeeG. Romeo OriginalPaper Pages: 101 - 108
Fatigue-crack propagation behavior of type 304 stainless steel in a liquid sodium environment Lee A. JamesRobert L. Knecht OriginalPaper Pages: 109 - 116
Permeation of hydrogen through alpha iron R. F. MillerJ. B. HudsonG. S. Ansell OriginalPaper Pages: 117 - 121
The deformation behavior of the matrix near a planar interface in a two-phase medium K. JagannadhamK. S. Raghavan OriginalPaper Pages: 123 - 127
The effect of thermal cycling on the mechanical properties of various aluminum alloys reinforced with unidirectional boron fibers M. A. Wright OriginalPaper Pages: 129 - 134
Grain refinement through thermal cycling in an Fe-Ni-Ti cryogenic alloy S. JinJ. W. MorrisV. F. Zackay OriginalPaper Pages: 141 - 149
Quantitative microstructural characterization of aligned eutectics by electrical analog modeling W. G. WatsonW. C. HahnR. W. Kraft OriginalPaper Pages: 151 - 158
Analysis of liquid metal embrittlement from a bond energy viewpoint M. J. KelleyN. S. Stoloff OriginalPaper Pages: 159 - 166
On the subsequent yielding of an aluminum alloy following cyclic prestraining J. LipkinJ. C. Swearengen OriginalPaper Pages: 167 - 177
Grain growth in dispersion strengthened superalloys by moving zone heat treatments R. L. CairnsL. R. CurwickJ. S. Benjamin OriginalPaper Pages: 179 - 188
Effect of thermal and thermo-mechanical processing on the properties of Al-Mg alloys M. ConservaM. Leoni OriginalPaper Pages: 189 - 195
The dendrite arm spacings of aluminum-copper alloys solidified under steady-state conditions K. P. YoungD. H. Kerkwood OriginalPaper Pages: 197 - 205
The thermally activated dislocation motion in neutron irradiated iron-nickel alloys C. T. K. KuoR. J. Arsenault OriginalPaper Pages: 207 - 212
Effect of aluminum addition on the precipitation behavior of a Co-Ni-Cr base superalloy containing Nb C. RavindranM. C. Chaturvedi OriginalPaper Pages: 213 - 217
Effect of solutes on preferred orientation in high-purity aluminum R. V. BelluzK. T. Aust Communication Pages: 219 - 220
Discussion of “an optimal design of a high strength, ductile metallic material: Criteria and application to aβ-titanium alloy” H. J. Rack Communication Pages: 220 - 221
Some aspects of precipitation of copper and columbium (Nb) carbide in an experimental high strength steel M. R. KrishnadevA. Galjbois Communication Pages: 222 - 224
The ferrite/austenite equilibrium in the Fe-Cr system (discussion of reference 1) Gernot KjrchnerBjörn Uhrenius Communication Pages: 224 - 226
Direct evidence for boron segregation to grain boundaries in a nickel-base alloy by secondary ion mass spectrometry J. M. WalshB. H. Rear Communication Pages: 226 - 229
Discussion of “tensile properties to 650° C and deformation structures in a precipitation-strengthened Ti-Al alloy” Frank A. Crossley Communication Pages: 229 - 229
Production of homogeneous casts for use in microprobe analysis M. H. BurdenD. J. HebditchJ. D. Hunt Communication Pages: 230 - 232
Further observations on the effect of grain boundary segregation in the hydrogen embrittlement of nickel R. M. LatanisionH. Opperhauser Communication Pages: 233 - 234
Kinetics of the diffusion controlled peritectic reaction during solidification of iron-carbon-alloys Y. K. ChuangDieter ReinischKlaus Schwerdtfeger Communication Pages: 235 - 238
On the microstructure of extruded rods and drawn wires of beryllium G. Y. Chin Communication Pages: 238 - 240
A mechanism for the columnar to equiaxed transition in castings or ingots M. H. BurdenJ. D. Hunt Communication Pages: 240 - 241
The CsCl-type order-disorder transition temperature in VMn alloys Tomoo SuzukiMasuo Hagiwara Communication Pages: 241 - 242
Partial excess entropies of hydrogen in palladium alloys Ted B. FlanaganJ. F. Lynch Communication Pages: 243 - 245
Criterion for peritectic and eutectic reactions in ternary systems Raghaba P. Sahu Communication Pages: 248 - 249
Errata: Microdetermination of Dissolved Nitrogen and Oxygen in a Titanium Alloy by Secondary Ion Mass Spectrometry Joseph M. Walsh Erratum Pages: 249 - 249