Fabrication of bulk ultrafine-grained materials through intense plastic straining Patrick B. BerbonTerence G. LangdonMinoru Nemoto OriginalPaper Pages: 2237 - 2243
Microstructural characteristics of ultrafine-grained aluminum produced using equal-channel angular pressing Yoshinori IwahashiMinoru FurukawaTerence G. Langdon OriginalPaper Pages: 2245 - 2252
Microstructures and properties of nanocomposites obtained through SPTS consolidation of powders I. V. AlexandrovR. K. IslamgalievT. C. Lowe OriginalPaper Pages: 2253 - 2260
Mechanical behavior of a bulk nanostructured iron alloy J. E. CarsleyA. FisherE. C. Aifantis OriginalPaper Pages: 2261 - 2271
Effect of B on the microstructure and mechanical properties of mechanically milled TiAl alloys Sang H. KimNack J. KimS. J. Hwang OriginalPaper Pages: 2273 - 2283
Mechanical properties, ductility, and grain size of nanocrystalline iron produced by mechanical attrition T. R. MalowC. C. Koch OriginalPaper Pages: 2285 - 2295
A transmission electron microscope study of 1 Pct Mn ductile iron with different austempering treatments M. Nili Ahmadabadi OriginalPaper Pages: 2297 - 2306
Static recrystallization kinetics with homogeneous and heterogeneous nucleation using a cellular automata model R. L. GoetzV. Seetharaman OriginalPaper Pages: 2307 - 2321
Analysis of ridging in aluminum auto body sheet metal A. J. BeaudoinJ. D. BryantDavid A. Korzekwa OriginalPaper Pages: 2323 - 2332
Heterogeneous microstructures and microtextures in cube-oriented al crystals after channel die compression Qing LiuNiels HansenJulian Driver OriginalPaper Pages: 2333 - 2344
High-temperature deformation of commercial-purity aluminum E. S. PuchiM. H. Staia OriginalPaper Pages: 2345 - 2359
An investigation of the fracture and fatigue crack growth behavior of forged damage-tolerant niobium aluminide intermetallics F. YeC. MerCerW. O. Soboyejo OriginalPaper Pages: 2361 - 2374
Microstructural and compositional transients during accelerated directional solidification of Al-4.5 wt pct Cu Rong-Jiunn SuRuel A. OverfeltWartan A. Jemian OriginalPaper Pages: 2375 - 2381
Enhancement of the mechanical properties of a low-carbon, low-silicon steel by formation of a multiphased microstructure containing retained Austenite P. JacquesF. DelannayJ. Ladriere OriginalPaper Pages: 2383 - 2393
The sweep constant concept in phase coarsening C. S. PandeR. A. MasumuraS. P. Marsh OriginalPaper Pages: 2395 - 2398
Transmission electron microscope specimen preparation of Zn powders using the focused ion beam lift-out technique B. I. PrenitzerL. A. GiannuzziT. L. Shofner OriginalPaper Pages: 2399 - 2406
Investigation of thermomechanical behavior of a work roll and of roll life in hot strip rolling C. G. SunS. M. HwangJ. S. Chung OriginalPaper Pages: 2407 - 2424
A novel way of amorphous phase formation during mechanical alloying of copper and cadmium powders D. L. ZhangT. B. Massalski OriginalPaper Pages: 2425 - 2432
Optimization of the strength-fracture toughness relation in particulate-reinforced aluminum composites via control of the matrix microstructure I. DuttaT. R. McNelleyF. N. Quiles OriginalPaper Pages: 2433 - 2446
Discussion of “Effect of dendrite arm coarsening on microsegregation” T. KraftY. A. Chang Communications Pages: 2447 - 2449
