Thermodynamic activities and phase boundaries for the alloys of the solid solution of Co in Ni3Al M. AlbersD. KathK. Hilpert OriginalPaper Pages: 2183 - 2188
The evolution of solutions: A thermodynamic analysis of mechanical alloying A. Y. BadmosH. K. D. H. Bhadeshia OriginalPaper Pages: 2189 - 2194
Effect of carbon and nitrogen on chemical homogeneity of fcc iron-based alloys V. G. GavriljukA. L. SozinovV. V. Runov OriginalPaper Pages: 2195 - 2199
Plate-shaped transformation products in zirconium-base alloys S. BanerjeeG. K. DeyS. Ranganathan OriginalPaper Pages: 2201 - 2216
Evolution of recrystallization texture from aluminum sheet cold rolled under unlubricated condition Chang-Hee ChoiDong Nyung Lee OriginalPaper Pages: 2217 - 2222
Synthesis of nanodispersed phases during rapid solidification and crystallization of glasses in Ti75Ni25 alloys R. NagarajanK. AokiK. Chattopadhyay OriginalPaper Pages: 2223 - 2232
Modeling the flow behavior of a medium carbon microalloyed steel under hot working conditions J. M. CabreraA. Al OmarJ. J. Jonas OriginalPaper Pages: 2233 - 2244
Damage effect on the fracture toughness of nodular cast iron: Part I. Damage characterization and plastic flow stress modeling M. J. DongC. PrioulD. François OriginalPaper Pages: 2245 - 2254
Damage effect on the fracture toughness of nodular cast iron: Part-II. Damage zone characterization ahead of a crack tip M. J. DongC. PrioulD. François OriginalPaper Pages: 2255 - 2262
Contact of crack surfaces during fatigue: Part 1. formulation of the model Ana María GarcíaHuseyin Sehitoglu OriginalPaper Pages: 2263 - 2275
Contact of crack surfaces during fatigue: Part 2. Simulations Huseyin SehitogluAna María García OriginalPaper Pages: 2277 - 2289
Effect of impurity hydrogen on the deformation and fracture in an Al-5 mass Pct Mg alloy Goroh ItohTakeshi JinkojiKatsumi Koyama OriginalPaper Pages: 2291 - 2295
Effects of test temperature, grain size, and alloy additions on the low-temperature fracture toughness of polycrystalline niobium A. V. SamantJ. J. Lewandowski OriginalPaper Pages: 2297 - 2307
Plastic-flow and microstructure evolution during hot deformation of a gamma titanium aluminide alloy V. SeetharamanS. L. Semiatin OriginalPaper Pages: 2309 - 2321
Influence of limit stress states and yield criteria on the prediction of forming limit strains in sheet metals W. M. SingK. P. RaoK. Swaminathan OriginalPaper Pages: 2323 - 2333
Effect of grain size on the observed pseudoelastic behavior of a Cu-Zn-Al shape memory alloy M. SomerdayJ. A. WertR. J. Comstock Jr. OriginalPaper Pages: 2335 - 2341
Modeling of rolling texture development in a ferritic chromium steel L. S. TóthA. MolinariD. Raabe OriginalPaper Pages: 2343 - 2351
Latent hardening behavior of monocrystalline Al-Mg solid solution Hsin-Ming WuMarek A. PrzystupaAlan J. Ardell OriginalPaper Pages: 2353 - 2360
The role of mass transport in the stress-corrosion cracking mechanism of Cu-25 At. Pct Au single crystals in chloride solutions C. J. Van der Wekken OriginalPaper Pages: 2361 - 2369
Particle fracture, retention, and fluid flow in metal matrix composite friction joints T. H. NorthG. J. BendzsakZ. Li OriginalPaper Pages: 2371 - 2384
Solidification of undercooled Fe-Cr-Ni alloys: Part III. Phase selection in chill casting Toshihiko KosekiMerton C. Flemings OriginalPaper Pages: 2385 - 2395
Anisotropic shrinkage during sintering of glass-powder compacts under uniaxial stresses: Qualitative assessment of experimental evidence Aldo R. BoccacciniEugene A. Olevsky OriginalPaper Pages: 2397 - 2404
Retained austenite characteristics in thermomechanically processed Si-Mn transformation-induced plasticity steels A. Zarei HanzakiP. D. HodgsonS. Yue OriginalPaper Pages: 2405 - 2414
The influence of austenite grain size and its distribution on chip deformation and tool life during machining of AISI 304L Laizhu JiangÅke RoosPing Liu OriginalPaper Pages: 2415 - 2422
Effect of laminate stacking sequence on the high frequency fatigue behavior of SCS-6 fiber-reinforced Si3N4 matrix composites Nikhilesh Chawla OriginalPaper Pages: 2423 - 2427
Development of reproducible and increased strength properties in thick extrusions of low-alloy Al-Zn-Mg-Cu based AA 7075 A. K. Mukhopadhyay Communications Pages: 2429 - 2433
Discussion of “kinetics and phase transformation evaluation of Fe-Zn-Al mechanically alloyed phases” Nai-Yong Tang Communications Pages: 2433 - 2434