A method of investigating the fracture of sheet materials in biaxial loading G. S. PisarenkoV. P. NaumenkoE. E. Onlshchenko Scientific-Technical Section Pages: 275 - 282
Strength of turbine parts in gas-turbine engines under complex loading conditions and associated problems N. D. Kuznetsov Scientific-Technical Section Pages: 283 - 288
Effect of stress-cycle asymmetry factor on the progress of fatigue and quasistatic fracture under low-cycle loading V. T. TroshchenkoV. A. StrizhaloV. V. Ivakhnenko Scientific-Technical Section Pages: 288 - 296
Evaluating critical curvature radii in stress concentration zones V. P. KogaevM. Ya. Gal'perin Scientific-Technical Section Pages: 296 - 301
Study of the scalar and vector properties of anisotropic materials under complex loading. Report no. 1. Yield condition of anisotropic materials A. A. LebedevV. V. KosarchukB. I. Koval'chuk Scientific-Technical Section Pages: 301 - 307
General principle of nondestructive mechanical methods of studying the residual stress state of coatings M. L. Kozlov Scientific-Technical Section Pages: 308 - 312
Principles of the mechanics of plastic materials M. Ya. LeonovB. A. Rychkov Scientific-Technical Section Pages: 313 - 319
Study of the stress-strain state near a joint between dissimilar elements of a pressure vessel Yu. N. Babich Scientific-Technical Section Pages: 319 - 323
Calculation of the state of thermal stress of steam turbine casings with a view to the circumferential inhomogeneity of temperature fields V. I. BerlyandA. A. GlyadyaS. S. Sokolovskaya Scientific-Technical Section Pages: 323 - 328
Method of large-scale modeling for estimating the fatigue limits of full-scale parts L. V. KonovalovV. P. Vandyshev Scientific-Technical Section Pages: 329 - 334
Experimental investigation of the effect of reactor irradiation on the resistance to alternating cyclic deformation of the heat-resistant steel 0Kh16N15M3B V. N. KiselevskiiD. F. KharitonovN. P. Losev Scientific-Technical Section Pages: 335 - 340
Effect of reactor irradiation on the long-term strength and creep of 0Kh16N15M3B steel in a plane stressed state. Part III. Experimental study of creep resistance G. P. KhristovB. D. KosovV. V. Samsonov Scientific-Technical Section Pages: 340 - 345
Influence of original structure on the radiation embrittlement of hardened and tempered 15Kh3MFA steel A. M. MorozovV. A. NikolaevV. V. Rybin Scientific-Technical Section Pages: 345 - 352
Fracture of LiF crystals with varied slip geometry T. S. OrlovaB. I. SmirnovV. V. Shpeizman Scientific-Technical Section Pages: 352 - 357
A model of failure in ideal elastoplastic media G. I. BykovtsevL. G. LukashevS. L. Stepanov Scientific-Technical Section Pages: 357 - 360
Low-cycle fatigue and special features of fracture of 30KhGSNA steel with a thick chrome coating Yu. M. DolzhanskiiO. D. Mit'kinaM. N. Tuchkevich Scientific-Technical Section Pages: 361 - 367
Method of calculating the optimum parameters of a multilayered coiled cylinder with constant tension of the strip during coiling A. F. Bezverbnyi Scientific-Technical Section Pages: 368 - 374
Experimental investigation of the bearing capacity of multilayered structures A. S. Dekhtyar'A. O. RasskazovV. S. Rublev Scientific-Technical Section Pages: 375 - 377
Effect of frequency differences between blades of small radially axial turbines on their state of stress O. K. SlivaA. A. KovadloV. Kh. Ivanyuk Scientific-Technical Section Pages: 378 - 383
Characteristics of cyclic creep resistance with an alternating load for steel 15Kh2NMFA V. V. Ivakhnenko Scientific-Technical Section Pages: 383 - 386
Fatigue resistance of heat-resistant alloy ÉI698VD under high temperature conditions A. V. ZheldubovskiiI. I. Ishchenko Scientific-Technical Section Pages: 386 - 389
Thermal-deformation curves for carbonized carbon plastics at elevated temperatures L. I. Gracheva Scientific-Technical Section Pages: 390 - 393
Ratio of the compression and tension creep rates of ceramic materials A. Ya. PerasV. P. Yakushka Scientific-Technical Section Pages: 394 - 396
Stress-intensity factors for the loading of one edge of a slot located in an elastic half space I. N. Zhukovskii Scientific-Technical Section Pages: 396 - 400
Character of residual stresses in the near-surface layers of alloys VT3-1 and VT22 after shot blasting R. G. GontarevaYu. V. PoloskinL. V. Tikhonov Scientific-Technical Section Pages: 400 - 402
Effect of prior residual deformation on the subsequent elastoplastic deformation of a material A. F. Nikitenko Scientific-Technical Section Pages: 402 - 406
Kinetics of bulk failure in an unoriented polymer A. Ya. Gol'dmanM. I. Gandel'smanS. Ya. Khaikin Scientific-Technical Section Pages: 406 - 410
Calculation of stretching diagrams for capron strip A. G. GiniyatullinA. M. Stalevich Scientific-Technical Section Pages: 411 - 414
The design strength of V95 aluminum alloy G. N. Golovin Scientific-Technical Section Pages: 415 - 418