1. Problems of the statics and dynamics of modern engineering designs. Status of the problem, new problems, and prospects

   • I. F. Obraztsov

   Scientific-Technical Section Pages: 1423 - 1433

2. Calculation of fatigue and life of crack-bearing structural elements under cyclic load

   • V. T. Troshchenko
   • P. V. Yasnii
   • V. V. Pokrovskii

   Scientific-Technical Section Pages: 1434 - 1439

3. Fracture toughness of aluminum alloys of the system Al-Mg-Si for cyclic and static loads

   • V. G. Kudryashov
   • Yu. K. Shtovba

   Scientific-Technical Section Pages: 1439 - 1443

4. Calculation of the static crack propagation trajectory

   • M. P. Savruk
   • P. N. Osiv

   Scientific-Technical Section Pages: 1443 - 1447

5. Fracture toughness of high-strength layered plates containing plastic interlayers with a high elastic modulus

   • E. N. Rudnitskii
   • P. G. Miklyaev
   • D. A. Andreev

   Scientific-Technical Section Pages: 1448 - 1450

6. Contour J-integral in the plastic region

   • Yu. G. Matvienko
   • V. Yu. Gol'tsev

   Scientific-Technical Section Pages: 1451 - 1455

7. Effect of loading-cycle asymmetry on the crack resistance of structural alloys

   • P. V. Yasnii
   • V. V. Pokrovskii
   • G. P. Karzov

   Scientific-Technical Section Pages: 1456 - 1461

8. Evaluating the limiting states of a steel under combined low-cycle loading and diffusion of sorbed hydrogen

   • V. V. Litvin
   • G. N. Tret'yachenko

   Scientific-Technical Section Pages: 1462 - 1466

9. Temperature-time dependence of the cyclic-creep activation energy of heat-resistant alloys

   • V. P. Golub

   Scientific-Technical Section Pages: 1466 - 1473

10. Study of the high-temperature creep of multilaminate iron/copper and nickel/copper condensates

    • B. A. Movchan
    • E. V. Dabizha
    • R. Nimmagadda

    Scientific-Technical Section Pages: 1474 - 1476

11. Evaluating the durability of materials on the basis of thermal fluctuation theory

    • E. S. Pereverzev

    Scientific-Technical Section Pages: 1477 - 1482

12. Analysis of damage accumulation in gas-turbine-engine blades subject to thermal cycling and vibration in a gas stream

    • G. N. Tret'yachenko
    • V. G. Barilo

    Scientific-Technical Section Pages: 1482 - 1489

13. Inelastic torsion of plane rods

    • M. Ya. Leonov
    • V. D. Perederii

    Scientific-Technical Section Pages: 1490 - 1493

14. Torsion of a rectangular beam with circular cavities

    • O. P. Orzhekhovskaya

    Scientific-Technical Section Pages: 1494 - 1497

15. Torsion of rods of hardening material with almost-circular cross section

    • S. B. Maksimov
    • V. A. Lupin
    • L. V. Maksimova

    Scientific-Technical Section Pages: 1498 - 1501

16. Plastic bands at the tip of a linear rigid inclusion

    • L. T. Berezhnitskii
    • N. M. Kundrat

    Scientific-Technical Section Pages: 1502 - 1505

17. Thermoelectric method for studying stresses in plates weakened by holes

    • V. Ya. Bash

    Scientific-Technical Section Pages: 1506 - 1508

18. Stress state of a heated flattened spherical shell caused by thermal diffusion

    • R. N. Shvets
    • M. S. Ravrik
    • A. L. Bichuya

    Scientific-Technical Section Pages: 1509 - 1515

19. Analysis of process stresses in two-layer SiC-Si disks

    • A. S. Tsybenko
    • A. L. Maistrenko
    • V. L. Yupko

    Scientific-Technical Section Pages: 1515 - 1518

20. Effect of shear modulus on the elastic behavior of strongly anisotropic plates

    • Yu. A. Bogan

    Scientific-Technical Section Pages: 1518 - 1523

21. Influence of the level of stresses on the static Young's modulus of a number of constructional materials

    • A. F. Voitenko
    • Yu. D. Skripnik
    • G. N. Nadezhdin

    Scientific-Technical Section Pages: 1524 - 1526

22. Determination of certain elastic characteristics of materials with the use of parabolic interpolation of strain curves

    • Yu. D. Skripnik

    Scientific-Technical Section Pages: 1527 - 1531

23. Influence of alloying on the strength of vanadium

    • G. G. Maksimovich
    • E. M. Lyutyi
    • G. N. Per'kova

    Scientific-Technical Section Pages: 1531 - 1535

24. Intergranular brittle fracture resistance of 18Kh2N4VA steel after hardening

    • G. A. Filippov
    • O. N. Chevskaya

    Scientific-Technical Section Pages: 1536 - 1540

25. Influence of the degree of preliminary strain on the strain aging of pearlitic casing steel

    • V. A. Yukhanov
    • S. I. Arkhangel'skii
    • S. I. Markov

    Scientific-Technical Section Pages: 1540 - 1544

26. Experimental examination of the strength of a glass-fiber plastic with longitudinal-transverse reinforcement in the plane stress state

    • V. I. Kulik
    • E. V. Meshkov
    • Z. T. Upitis

    Scientific-Technical Section Pages: 1544 - 1550

27. Strength of porous net materials in the uniaxial strain state

    • A. F. Tret'yakov
    • G. P. Polushkin
    • A. D. Panov

    Scientific-Technical Section Pages: 1551 - 1556

28. Fracture mechanics of syntactic foam composites

    • P. G. Krzhechkovskii

    Scientific-Technical Section Pages: 1556 - 1564

29. Examination of the stress state of a helically reinforced composite in shearing

    • G. E. Freger

    Scientific-Technical Section Pages: 1564 - 1568

30. Software for automatic loading controls in strength testing

    • V. I. Litvak
    • V. M. Gal'perin

    Production Section Pages: 1569 - 1573