Improving the production of alumino-silicate cement concrete blocks at the Kuznets Metallurgical Combine B. L. IzhboldinA. F. KuznetsovG. I. Kozlov Production Pages: 453 - 456
Improving the mineral composition of refractories for the cement industry V. I. ShubinI. S. KainarskiiK. V. Simonov Production Pages: 456 - 460
Parameters of the kinetics of drying refractory concretes I. P. TsibinA. A. ShershnevÉ. P. Taigil'dina Thermal Engineering Pages: 461 - 465
Mechanized method of gathering screes A. A. MalyuginA. S. Fedosov Equipment, Mechanization, and Automation of Production Pages: 466 - 467
Use of an electric hammer for splitting oversize magnesite blocks Yu. F. KabachkovB. M. VainerV. V. Lesnikov Equipment, Mechanization, and Automation of Production Pages: 468 - 469
Electrical coagulation of finely dispersed kaolin aerosols L. I. EshchenkoN. P. PermiginV. F. Danilin Protection of the Environment Pages: 470 - 472
Fundamental positions of a rational method of testing refractory clays and kaolins for certification G. M. KatorginN. R. Pomeranets Raw Materials Pages: 473 - 476
Gas-flame atomization for the application of aluminosilicate coatings L. M. Demidenko Refractories for the Consumers Pages: 477 - 483
Introduction of a method of producing a monolithic lining for 150-ton steel teeming ladles at Krivoi Rog Steel Plant Yu. A. PirogovM. I. ProkopenkoV. S. Koshechko Refractories for the Consumers Pages: 484 - 485
Influence of various forms of refractories and firing conditions on the water-soluble chromium content in cement clinker V. G. SolonetskiiV. N. KravchenkoA. Kh. Evangelidi Refractories for the Consumers Pages: 486 - 488
Influence of cyclic freezing on the properties of refractories V. Ya. TolstayaV. P. SafronovaV. S. Tolstoi Refractories for the Consumers Pages: 489 - 490
Effect of the type of binding material on the properties of refractory glass-fiber heat-insulation products V. V. MartynenkoA. N. GaoduÉ. V. Degtyareva Research Pages: 491 - 497
Electrohydraulic-impulse pressing of refractory powders K. N. BogoyavlenskiiP. A. KuznetsovV. M. Yam Research Pages: 498 - 503
How corundum refractories are wetted by molten steel A. E. ZhukovskayaA. A. Kortel'T. P. Korableva Research Pages: 504 - 507
Mechanical properties of glass-crystal structures based on corundum I. I. VishnevskiiN. D. Tal'yanskaya Research Pages: 508 - 514
Melting diagram of the CaAl2O4-CaAl4O7-MgCr2O4 system N. G. IlyukhaM. T. Mel'nikF. Hesse Research Pages: 515 - 516
Production process for fused periclase powders used in the lining of electric smelting furnaces K. V. SimonovE. P. MezentsevM. K. Kolchin Production Pages: 519 - 526
Choosing the travel schedule for a tunnel kiln hearth V. G. AbbakumovS. I. Vel'sin Heat Technology Pages: 527 - 534
Equipment for isostatic pressing of refractories (review) Ya. M. GrinbergÉ. V. Degtyareva Equipment, Mechanization, and Automation of Production Pages: 535 - 540
Technical progress at the Velikoanadol'sk Refractory Combine N. S. ShevtsovR. N. IshchenkoG. I. Ivanov Equipment, Mechanization, and Automation of Production Pages: 541 - 542
Installation of the ÉSh-10/70A stepping excavator at the Borovich Refractory Combine Yu. P. GromovB. M. Dmitriev Equipment, Mechanization, and Automation of Production Pages: 542 - 546
A thyristor controller for furnaces with silicon carbide heaters A. N. Balykin Equipment, Mechanization, and Automation of Production Pages: 546 - 547
Gas cleaning by granular filters in refractory production V. Ya. BashkardinYu. D. SagalevichI. G. Kal'chik Preventing Atmospheric Pollution Pages: 548 - 552
Refractory masses based on fine quartz sand for the tamped linings of walls of low-tonnage steel-smelting arc furnaces V. M. SoiferN. I. MosolovaV. S. Kozlova Refractories for the Consumer Pages: 553 - 555
Heat insulation for a high-temperature thermocouple block O. N. ErmakovV. A. Emel'yanovV. V. Ryabov Refractories for the Consumer Pages: 555 - 556
Effect of heat treatment on the structure and properties of fused periclase V. A. BronI. S. RaevaV. G. Sivash Research Pages: 557 - 562
Relationship between the cracking resistance and the structure of refractory ceramics G. A. Prantskyavichyus Research Pages: 562 - 565
Analysis of the grain-size composition of refractory powders using the VSA-500 mg automatic sedimentation balance F. S. KaplanI. I. KoryakinaV. A. Pavlova Research Pages: 565 - 569