1. Attritor milling of titanium carbide and titanium nitride produced by self-propagating high-temperature synthesis

   • R. A. Andrievskii
   • A. Zh. Dzneladze
   • S. V. Yudin

   Theory, Production Technology, and Properties of Powders and Fibers Pages: 867 - 869

2. Production of very fine TiN-Mo composite powders in a low-temperature plasma stream

   • T. V. Rezchikova
   • I. A. Domashnev
   • Yu. M. Shul'ga

   Theory, Production Technology, and Properties of Powders and Fibers Pages: 869 - 873

3. Evaluation of force and kinematic parameters in the compression of sintered porous blanks

   • I. D. Radomysel'skii
   • G. A. Baglyuk
   • G. G. Serdyuk

   Theory and Technology of the Component Formation Process Pages: 874 - 877

4. Continuous shaping of tubes from metal powders

   • A. V. Stepanenko
   • L. A. Isaevich
   • A. A. Veremeichik

   Theory and Technology of the Component Formation Process Pages: 878 - 882

5. Stressed-strained state of powder being rolled in the densification zone. I. Mathematical model of rolling in the densification zone

   • V. P. Katashinskii
   • M. B. Shtern

   Theory and Technology of the Component Formation Process Pages: 882 - 885

6. Computer modeling and investigation of the process of rolling of porous materials

   • G. Ya. Gun
   • S. A. Stebunov
   • A. A. Frolov

   Theory and Technology of the Component Formation Process Pages: 886 - 890

7. Carburization of P/M steels alloyed with copper and phosphorus

   • F. G. Lovshenko
   • V. T. Vysotskii

   Theory and Technology of Sintering, Thermal, and Chemicothermal Treatment Processes Pages: 891 - 894

8. Dilatometric and thermographic investigation of the reactive sintering of titanium nickelide. I. Production of porous titanium nickelide by reactive sintering

   • I. F. Martynova
   • V. Ya. Petrishchev
   • V. V. Skorokhod

   Theory and Technology of Sintering, Thermal, and Chemicothermal Treatment Processes Pages: 895 - 899

9. Production of a sintered tungsten-rhenium alloy at low temperatures

   • V. V. Skorokhod
   • O. G. Radchenko
   • V. V. Panichkina

   Powder Metallurgical Materials, Parts, and Coatings Pages: 900 - 903

10. Cleaning the basis metal of surface films in the spray-deposition of powders

    • Yu. A. Kharlamov

    Powder Metallurgical Materials, Parts, and Coatings Pages: 904 - 909

11. Electric-spark alloying of steels with TiN-Cr materials

    • V. I. Poveshchenko
    • F. F. Egorov
    • A. D. Verkhoturov

    Powder Metallurgical Materials, Parts, and Coatings Pages: 910 - 915

12. Production and properties of reinforced laminated materials for filtration

    • V. K. Sorokin
    • G. F. Tikhonov

    Powder Metallurgical Materials, Parts, and Coatings Pages: 916 - 918

13. Erosion behavior of alloys of the transition metal carbide-boride system during electric-spark alloying

    • A. D. Verkhoturov
    • S. S. Ordan'yan
    • T. V. Kurinnaya

    Powder Metallurgical Materials, Parts, and Coatings Pages: 919 - 921

14. Thermodynamic properties of the gadolinium germanide GdGe_1.63

    • V. G. Batalin
    • G. M. Lukashenko
    • R. I. Polotskaya

    Test Methods and Properties of Powder Metallurgical Materials Pages: 922 - 923

15. Evaporation characteristics of praseodymium monobismuthide

    • G. Sh. Viksman
    • S. P. Gordienko

    Test Methods and Properties of Powder Metallurgical Materials Pages: 924 - 926

16. Homogeneity ranges of the MeNi₃ phases in the Ti-Ni-Mo system

    • S. B. Prima
    • B. S. Semukhin

    Test Methods and Properties of Powder Metallurgical Materials Pages: 926 - 928

17. Quantitative correlation between fracture toughness K_1C and the short-term strength σ_b, σ_0·2 of tungsten

    • A. V. Babak

    Test Methods and Properties of Powder Metallurgical Materials Pages: 928 - 932

18. Effect of impurity element substitution on the failure behavior of a W-Ni-Fe alloy

    • R. V. Minakova
    • L. G. Bazhenova
    • A. V. Tolstunov

    Test Methods and Properties of Powder Metallurgical Materials Pages: 932 - 937

19. Influence of cutting speed on the effectiveness of polishing with magnetic abrasive powders

    • V. E. Oliker
    • A. F. Zhornyak
    • T. Ya. Gridasova

    Test Methods and Properties of Powder Metallurgical Materials Pages: 938 - 942

20. Structure and properties of electrophoretic chromium carbide coatings with a eutectic composition nickel-boron binder

    • V. V. Furman
    • G. K. Gaiduchenko
    • V. B. Deimontovich

    Test Methods and Properties of Powder Metallurgical Materials Pages: 942 - 945

21. Interaction in the LaB₆-ZrB₂ system

    • S. S. Ordan'yan
    • Yu. B. Paderno
    • E. V. Maksimova

    Test Methods and Properties of Powder Metallurgical Materials Pages: 946 - 948

22. Design strength of powder metallurgy steels produced by dynamic hot pressing

    • Yu. G. Dorofeev
    • N. A. Shtepin
    • K. K. Lamkov

    Test Methods and Properties of Powder Metallurgical Materials Pages: 949 - 952

23. Structure and thermal expansion of NbC base complex carbides

    • I. M. Khatsinskaya
    • I. N. Chaporova
    • L. P. Dodonova

    Test Methods and Properties of Powder Metallurgical Materials Pages: 952 - 956

24. Influence of premolding pressure in electric-discharge sintering on the physicomechanical properties of a copper-tin-abrasive composite

    • T. I. Istomina
    • A. A. Baidenko
    • A. V. Svechkov

    Test Methods and Properties of Powder Metallurgical Materials Pages: 957 - 960

25. Mechanical properties of zirconium carbide-cobalt materials

    • N. I. Demidenko
    • A. S. Vlasov
    • B. S. Skidan

    Test Methods and Properties of Powder Metallurgical Materials Pages: 960 - 964