Vacuum-evaporation assembly for the evaporation of yeast suspensions P. F. SavenkovYu. N. PiskunovV. F. Sushchenko New Machinery and Equipment Pages: 395 - 397
Apparatus for single-channel differentiated separate water injection into two tiers of one oil well Sh. T. DzhafarovO. I. ÉfendievL. V. Perevezentsev New Machinery and Equipment Pages: 398 - 399
Analysis of stresses in the separator rotor by optical simulation and with electrical strain gages B. F. GusakovS. M. Kutepov Construction and Design of Machinery and Apparatus Pages: 400 - 405
Effect of installed length of multilayer bellows on cyclic strength V. E. AlekseevN. I. IvanovV. S. Chukhin Construction and Design of Machinery and Apparatus Pages: 406 - 407
Calculation of the hermeticity of flanged connections with a tongue and groove type teflon seal under variable internal pressures and temperatures P. A. PavlovYu. É. KhanguE. M. Budin Construction and Design of Machinery and Apparatus Pages: 408 - 410
A preliminary tightening of shut-off devices with profiled obturators A. F. PershinV. D. ProdanYu. A. Davankov Construction and Design of Machinery and Apparatus Pages: 411 - 414
Investigation and calculation of thermo chemical processes analysis of preliminary air-cooling systems of air-separating installations V. D. Dobud'koV. S. KortLkov Construction and Design of Machinery and Apparatus Pages: 415 - 419
Tubular heat exchangers for helium refrigeration plant O. K. KrasnikovaV. V. UsanovG. A. Kondrat'eva Construction and Design of Machinery and Apparatus Pages: 420 - 424
Investigation into the head characteristic of a sectional low-speed centrifugal pump stage V. A. GolovinV. V. Malyushenko Construction and Design of Machinery and Apparatus Pages: 425 - 427
Determination of the first stage of intercrystalline corrosion caused by a highly corrosive medium P. N. ZelentsovV. I. BurlakovB. V. Red'kin New Materials and Corrosion Control Pages: 428 - 431
The technology of casting enameled iron lids A. V. BorodinN. P. Dolgikh The Technology of Producing Equipment Pages: 432 - 433
Selecting the optimum cast iron composition for rotary compressor cylinder castings Yu. S. ShepelevL. F. RudenkoA. I. Likhachev The Technology of Producing Equipment Pages: 434 - 436
Effect of heat-treatment conditions on the structure and mechanical properties of heat-resistant centrifugally cast type 25kh20n33 steel after high-temperature service N. F. ChermenskayaO. M. Kop'evaA. I. Elizov The Technology of Producing Equipment Pages: 437 - 439
A method of producing rotors for small blowers from AG-4V pressed material E. N. KislyukV. N. KushnarevV. I. Fomenko The Technology of Producing Equipment Pages: 440 - 444
Industrial standard for calculating the reinforcement of holes in shells, cross-overs, and bottom-plates A. V. GornostaevYu. P. SimonovV. A. Freitag Normalization and Standardization Pages: 445 - 447
Standardization of mixers used in the preparation of paste-like and loose materials I. A. StoikovV. D. Ivbul' Normalization and Standardization Pages: 448 - 450
Normative base of machine-building enterprises and some directions of its improvement R. A. KorenchenkoT. D. Kurkina Industrial Organization and Economics Pages: 451 - 453
Engineering-cost calculation of capital expenditure for chemical and petrochemical plant piping V. V. KafarovV. L. PervovN. M. Chugunova Industrial Organization and Economics Pages: 454 - 456
Reliability of M10 base opposed compressor-lubrication systems N. I. ArslanovL. A. Gershbautn Quality, Reliability, and Service Life Pages: 457 - 461
Chemical resistance of packing materials for petroleum and gas industry equipment Kh. T. KakhramanovR. S. SafarovT. B. Gavrilova Quality, Reliability, and Service Life Pages: 462 - 464
Electropulse method of producing screens V. A. KostyuchenkoN. P. Galyan Exchange of Experience Pages: 465 - 466
Casting a 450 MM diameter aluminum pan by a pressing method D. Ya. LigunV. P. Saenko Exchange of Experience Pages: 469 - 470
Remote control by a regulatable electric drive in locations having an explosion hazard B. I. GladyshevL. M. Bespalaya Information Pages: 472 - 476
Testing of the zigzag classifier for granulated materials B. N. FastovP. F. ValuiskiiG. N. Oskalenko Information Pages: 477 - 479
Testing of devices for the suppression of foam in evaporators V. F. SushchenkoE. M. Kovalev Information Pages: 480 - 481
Papers deposited at T sINTikhimneftemash M. A. BalabudkinT. B. TokarevaR. G. Zinchenko Information Pages: 482 - 483