Abstract
Background
For biofuel production processes to be economically efficient, it is essential to maximize the production of monomeric carbohydrates from the structural carbohydrates of feedstocks. One strategy for maximizing carbohydrate production is to identify less recalcitrant feedstock cultivars by performing some type of experimental screening on a large and diverse set of candidate materials, or by identifying genetic modifications (random or directed mutations or transgenic plants) that provide decreased recalcitrance. Economic efficiency can also be increased using additional pretreatment processes such as deacetylation, which uses dilute NaOH to remove the acetyl groups of hemicellulose prior to dilute acid pretreatment. In this work, we used a laboratory-scale screening tool that mimics relevant thermochemical pretreatment conditions to compare the total sugar yield of three near-isogenic brown midrib (bmr) mutant lines and the wild-type (WT) sorghum cultivar. We then compared results obtained from the laboratory-scale screening pretreatment assay to a large-scale pretreatment system.
Results
After pretreatment and enzymatic hydrolysis, the bmr mutants had higher total sugar yields than the WT sorghum cultivar. Increased pretreatment temperatures increased reactivity for all sorghum samples reducing the differences observed at lower reaction temperatures. Deacetylation prior to dilute acid pretreatment increased the total sugar yield for all four sorghum samples, and reduced the differences in total sugar yields among them, but solubilized a sizable fraction of the non-structural carbohydrates. The general trends of increased total sugar yield in the bmr mutant compared to the WT seen at the laboratory scale were observed at the large-scale system. However, in the larger reactor system, the measured total sugar yields were lower and the difference in total sugar yield between the WT and bmr sorghum was larger.
Conclusions
Sorghum bmr mutants, which have a reduced lignin content showed higher total sugar yields than the WT cultivar after dilute acid pretreatment and enzymatic hydrolysis. Deacetylation prior to dilute acid pretreatment increased the total sugar yield for all four sorghum samples. However, since deacetylation also solubilizes a large fraction of the non-structural carbohydrates, the ability to derive value from these solubilized sugars will depend greatly on the proposed conversion process.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Background
Sorghum (Sorghum bicolor L. Moench) is an important grain and forage crop around the world. The interest in sorghum as an important potential source of biomass for biofuel and biochemical productions has also been growing because of its availability and sustainability [1, 2]. Sorghum is an annual tropical grass that fixes carbon through C4 photosynthesis. This crop is easily established, tolerant to drought, has low water needs, efficiently uses nutrients, has high dry matter harvest yields, is digestible for livestock, and is economical to produce. Sorghum is often grown in areas that are too hot and dry for corn [1, 2].
To improve its digestibility for cattle while maintaining similar dry matter harvest yields, brown midrib (bmr) sorghum mutants were isolated from chemically mutagenized populations. Both bmr6 and bmr12 mutants are available in commercial sorghum lines [2]. The bmr6 gene encodes a cinnamyl alcohol dehydrogenase (CAD2) enzyme while the bmr12 gene encodes for a caffeic O-methyltransferase (COMT) enzyme. The alleles of bmr6 and bmr12, respectively, are nonsense mutations, and are likely “null alleles,” because stop codons are predicted to prematurely truncate the respective peptide prior to conserved catalytic domain of the proteins. Their respective transcripts and protein are nearly undetectable [3, 4]. These bmr mutants have an improved digestibility for ruminants because of their reduced lignin content [2] although some work has shown slightly lower harvest yields [5]. Lignin is a phenylpropane macromolecule found in the cell walls of all vascular plants. It is essential to those plants because it provides them mechanical and structural rigidity and protects them from abiotic and biotic stresses. Lignin also forms a barrier surrounding the plants’ polysaccharides: cellulose, hemicelluloses, and pectins and thus it inhibits the enzymatic hydrolysis of plant cell wall polysaccharides in the rumen as well as in bioconversion processes for biofuel and biochemical production [5, 6]. Indeed, we have shown a strong negative correlation between the lignin content and the total sugar yields from structural of glucan and xylan in a laboratory-scale dilute acid pretreatment and enzymatic hydrolysis assay for a wide variety of herbaceous biomass feedstocks including sorghum [7].
The bioconversion of cellulosic biomass to biofuels typically consists of three distinct steps: pretreatment, enzymatic hydrolysis, and fermentation. The first two steps enable the release of monomeric sugars from the structural carbohydrates in the biomass, while the third step is the microbial conversion of the released sugars (mainly glucose and xylose) to the desired biofuel (e.g., ethanol and butanol). For a biofuel production process to be economically efficient, it must be able to produce and then convert soluble monomeric sugars from the structural glucan and xylan of the biomass [8–10]. Therefore, it is essential to identify less recalcitrant biomass feedstocks and develop a process to enhance the reactivity of these feedstocks while reducing inputs (e.g., energy and chemicals). Less recalcitrant feedstocks can be identified by screening diverse panel plant cultivars [7] or through genetic modifications that affect lignin synthesis, such as the bmr mutants described above. The thermal, chemical, and physical conditions of the pretreatment step enable us to open up the cell wall structure to expose the glucan and xylan to the enzymes of the enzymatic hydrolysis step [11]. Preprocessing biomass can improve the reactivity of the biomass prior to the thermochemical pretreatment [12]. For example, deacetylation with dilute sodium hydroxide (NaOH) removes the acetyl groups from the xylan backbone of the hemicelluloses. Soluble components such as ash, protein, and non-structural carbohydrates are also removed, enriching the glucan and xylan fractions. The deacetylation is typically performed at NaOH concentrations of 0.2–0.4% (w/w) and temperatures of 60–80 °C for 30–180 min [13, 14]. Removing the acetyl groups improves the total sugar yield of the biomass during the enzymatic hydrolysis step and also reduces the concentration of fermentation inhibitors such as acetic acid in the enzymatic hydrolyzate [13]. Studies are available on the deacetylation of corn, but not yet on sorghum. One of those studies shows a strong negative correlation between the degree of acetylation of the corn stover biomass and the enzymatic hydrolysis yield [15].
The purpose of this work is to compare the sugar yields of wild-type (WT) sorghum to its near-isogenic bmr lines, which have reduced lignin content, using a laboratory-scale deacetylation and dilute acid pretreatment and enzymatic hydrolysis assay. This work builds on the work of [6], which examined the dilute acid pretreatment of sorghum bmr mutants and WT cultivars. In this work, we use a similar sorghum variety (AWheatland) for which the bmr sorghum mutants are known to have similar biomass yields compared to WT [2, 3, 16]. We extend this work by examining a wider variety of dilute acid pretreatment conditions, by evaluating the effect of deacetylation prior to dilute acid pretreatment on the total sugar yield from these sorghum samples, and by comparing the relative performance of the sorghum mutants from this laboratory-scale assay with the relative performance in a larger and more process-relevant pretreatment reactor.
Results and discussion
A note on total sugar yield calculations
For this study, the total sugar yield of the feedstocks is expressed as the combined yield of glucose and xylose from the corresponding structural carbohydrates glucan and xylan. A yield calculation is typically a ratio, with the numerator containing the mass of product released, and the denominator containing the mass of reactant originally present. For this work, the yield numerator is the sum of glucose and xylose released in their monomeric or oligomeric forms by all pretreatments (deacetylation and/or dilute acid pretreatment) and the monomeric glucose and xylose released by enzymatic hydrolysis. The denominator is the glucan and xylan content contained in the feedstock (including the anhydro correction factor) prior to any pretreatment or enzymatic hydrolysis. However, the presence of non-structural carbohydrates (free glucose, sucrose, and starch) in the feedstock elevates the apparent glucose yield. There are two ways to account for the presence of the non-structural derived glucose in the calculated yield:
-
1.
Adding the non-structural glucose (expressed in its monomeric form) to the denominator (DE) of the yield. This will correspond to the total glucose and xylose yield from both structural and non-structural carbohydrates. This yield expression focuses on the availability of all potentially fermentable carbohydrates.
-
2.
Subtracting the non-structural glucose content (expressed in its monomeric form) from the numerator (NU) of the yield. This assumes all non-structural carbohydrates are converted to glucose, and makes the resulting yield calculation correspond to the glucose and xylose yield from only structural carbohydrates. This yield expression focuses on the sugar yield from the structural carbohydrates of the feedstock.
Either method is valid, although there might be compelling reasons to use one calculation over the other, depending on the specific research question to be answered. Regardless, it is important to keep in mind how the total sugar yield is calculated. In this work, we use the DE method, and focus on the availability of all potentially fermentable carbohydrates. We present yields calculated with both the DE and NU method in Additional file 1.
The fate of the non-structural carbohydrates (principally glucose) released during deacetylation should also be considered with caution. In the current state of cellulosic conversion technology, the deacetylation stream is burned for energy, and any solubilized carbohydrates in this stream cannot be recovered [14]. For the glucose and xylose yields in this work, we define the “no-loss recovery” (NL) to include all sugars solubilized during deacetylation and the “loss recovery” (LO) to exclude all sugars solubilized during deacetylation. We compare the two calculations when we assess the impact of deacetylation on the total sugar yield.
Feedstock compositional analysis
The chemical composition [glucan, xylan, galactan, arabinan, acetyl, acid-soluble lignin, insoluble (Klason) lignin, total lignin, starch, total soluble sugars, water extractives, ethanol extractives, proteins, and mineral compounds] of the near-isogenic sorghum lines [wild type (WT), bmr6 mutant, bmr12 mutant, and bmr6 bmr12 stacked mutant (SM)] are shown in Table 1. The non-structural carbohydrate content (total soluble sugars and starch) of the analyzed sorghum feedstocks represented nearly 20% of their mass. Thus, the glucose released from those non-structural carbohydrates can be expected to have a significant effect on the total glucose yield, as we will show later in this report.
The detergent fiber composition (neutral detergent fiber (NDF), acid detergent fiber (ADF), acid detergent lignin (ADL), calculated cellulose (ADF-ADL), hemicellulose (NDF-ADF), and enzymatically digestible organic matter (eDOM) of the analyzed sorghum feedstocks are shown in Table 2. There were significant differences in total lignin, ADL, and eDOM among these four sorghums. The bmr sorghum lines compared to the WT had a reduced total lignin and ADL and an increased eDOM for all three lines. For total lignin, the reduction varies from 6 to 17%. For ADL, the reduction varies from 21 to 50%. For eDOM, the increase varies from 6 to 14%. Interestingly, the total lignin, ADL, and eDOM changes seem to be additive in the mutants when combined into the SM, which was also observed for total lignin and ADL in similar bmr materials [6]. The increase of the eDOM for bmr sorghums confirms that they are feedstocks with an improved digestibility for ruminants, likely because eDOM is highly correlated to the lignin content [17–19]. The bmr sorghum lines also had a significantly reduced acetyl content of at least 27% compared to the WT. A reduced lignin and acetyl content should increase the total sugar yield of the biomass from the bmr lines. The other structural components determined (glucan, xylan, NDF, ADF, cellulose Van Soest, and hemicelluloses Van Soest) were also affected by the bmr mutations.
The detergent fiber method is less reliable for estimating structural components (cellulose, hemicelluloses, and lignin) compared to the dietary fiber method [20]. For a feedstock such as sorghum, the detergent fiber method compared to the dietary fiber method overestimates cellulose and hemicelluloses, and underestimates lignin, as observed in the present study (Tables 1, 2) [20–23]. The ADL values were especially low, but they were consistent with those values observed by [6], which used the same bmr mutants in a different variety of sorghum. The chemical composition and detergent fiber composition analyses of the present study are consistent with that study; the main differences were that the sorghum samples of [6] contained much less mineral content and, therefore, had slightly higher concentrations of the other compounds compared to the results of Tables 1 and 2. In addition, the glucan, xylan, NDF, and ADF contents of the bmr6 mutant of the present study are lower compared to those of [6]. While these lines contain the same two bmr mutations, they are in a different genetic background. We used the “A Wheatland” variety, whereas the earlier work used the “Atlas” sorghum variety.
Total sugar yield: optimizing dilute acid pretreatment
The total sugar yields (combined glucose and xylose yield) of the near-isogenic sorghum lines with dilute acid pretreatment at different temperatures (150, 160, 170, and 180 °C), followed by enzymatic hydrolysis are illustrated in Fig. 1a, b. How the non-structural carbohydrates were accounted for in the calculation of total sugar yield (either subtracting the non-structural carbohydrates from the numerator, NU or adding them to the denominator, DE) has a modest impact on the calculated total sugar yield, with the DE calculation having calculated total sugar yields 2–8% higher (ANOVA p value <0.001) compared to total sugar yields from the NU calculation (data not shown). The difference is minor because the sugars in the dilute acid pretreatment liquor, regardless of their origin, are included in the total sugar yield. Note that the primary analytical data used for both of these calculations are identical; the differences in yields are due simply to how the total sugar yield calculation is performed. As mentioned above, we present all total sugar yields in this work using the DE calculation, focusing on the total soluble carbohydrate yield from both structural and non-structural carbohydrates.
Total sugar yield (g/g) of sorghums with dilute acid (DA) pretreatment (PT) on the ASE350 reactor and enzymatic hydrolysis. a Glucose and xylose yield from structural carbohydrates (NU). b Glucose and xylose yield from structural and non-structural carbohydrates (DE). Error bars correspond to 95% confidence interval of the mean
The total sugar yields of these sorghum feedstocks show the same trend with dilute acid pretreatment temperature as the feedstocks analyzed by [7]. Both the pretreatment temperature and the sorghum mutant have significant impacts (ANOVA p value <0.001) on the total sugar yield (Table 3). Figure 1a, b show that the optimal pretreatment temperature for all four sorghum feedstocks is approximately 160 °C. Above 160 °C, these feedstocks are “overcooked” and the total sugar yield drops (data included in Additional file 1). The total sugar yield of the SM is significantly higher than the WT (ANOVA p value <0.001, Table 3) at 150 °C, but not at the higher temperatures. Increasing the dilute acid pretreatment severity decreases the difference in recalcitrance between the feedstocks. This is supported by the ANOVA results in Table 3 as well, which shows a significant second-order interaction between feedstock type and temperature.
The total sugar yields calculated in this work (again, using the DE method), are higher than the results of [6], which likely used yields calculated in the same manner. These differences are expected since [6] used a lower dilute acid pretreatment temperature (121 °C) leading to lower conversions. We note that [6] observed a slightly larger improvement of the total sugar yield for the stacked mutant (SM) material compared to the WT cultivar. This may be an artifact of the differences in experimental systems, or a fundamental difference in the two sorghum cultivars used in these two works.
As noted in the “Methods” section, both monomeric and oligomeric sugars are released during the dilute acid pretreatment. Sugars in either form contribute to the total sugar yield. While more severe pretreatment conditions (e.g., longer times, higher temperatures, or higher acid concentrations) result in increased monomeric sugar yield and reduced oligomeric sugar yield, we did not observe any systematic difference in monomeric versus oligomeric sugar yield from the sorghum mutants studied in this work.
Total sugar yield: effect of deacetylation
We examined the effect of deacetylation prior to dilute acid pretreatment for dilute acid pretreatment temperatures of 150 and 160 °C only, since higher dilute acid pretreatment temperatures were clearly non-optimal. The results of these experiments are shown in Fig. 2 and Table 2. The total sugar yields presented in Fig. 2a assume all sugars solubilized during deacetylation are not lost during the deacetylation step while the yields presented in Fig. 2b assume that any solubilized sugars are lost during deacetylation. Deacetylation and increased dilute acid pretreatment temperature significantly increase the total sugar yield for all feedstocks, and the SM is more reactive than the WT (ANOVA p value <0.001, Table 3). For the DE-LO calculation, there is a significant (ANOVA p value <0.001) decrease (between 14 and 19%) of the total sugar yield due to deacetylation. This can be explained by the high content of non-structural carbohydrates in the analyzed sorghums (Table 1), since the DE-LO calculation assumes that non-structural carbohydrates (total soluble sugars and a fraction of starch) solubilized during deacetylation are lost prior to enzymatic hydrolysis.
Total sugar yield (g/g) of the sorghums with or without deacetylation on the ASE350 reactor and enzymatic hydrolysis. a Glucose and xylose yield from structural and non-structural carbohydrates, and no-loss recovery of carbohydrates solubilized during deacetylation (DE-NL). b Glucose and xylose yield from structural and non-structural carbohydrates, and loss recovery of carbohydrates solubilized during deacetylation (DE-LO). Error bars correspond to 95% confidence interval of the mean. DA dilute acid, PT pretreatment
A major aim of the deacetylation process is to solubilize the acetyl groups from the xylan chains. This solubilization was significantly (ANOVA p value <0.001) higher in bmr mutants (between 0.33 and 0.41 g/g) compared to the WT (0.23 g/g) (Table 4). The increased acetyl removal likely contributed to the higher total sugar yield of the deacetylated sorghums.
If we assume recovery of soluble sugars, deacetylation improves the total sugar yield for all feedstocks and both dilute acid pretreatment temperatures. However, the positive effect of deacetylation is less pronounced at the higher dilute acid pretreatment temperature, and the difference in total sugar yields between the mutants and the WT cultivar also diminish at the higher dilute acid pretreatment temperature. That is, the higher dilute pretreatment temperature increases the total sugar yield, but reduces the differences in recalcitrance among feedstocks and the effect of additional preprocessing using deacetylation. Again, these observations are supported by the statistically significant second-order effects in the ANOVA (Table 3).
Total sugar yield: ZipperClave reactor
We examined the behavior of the WT sorghum and the SM bmr mutant in the larger ZipperClave pretreatment reactor. The total sugar yield for the SM was higher than the WT for all three pretreatment temperatures investigated (Fig. 3). However, the measured total sugar yields from the ZipperClave experiments were lower than the corresponding total sugar yields determined using the ASE350 reactor system. This suggests that other factors, such as the method of heating (steam vs. electrical), mixing, heat transfer, and reactor configuration may have affected the pretreatment conversion in the ZipperClave reactor. Nonetheless, we saw consistent experimental results with both systems; higher dilute acid pretreatment temperatures increase total sugar yield, and a large improvement in total sugar yield with the SM mutant.
Conclusions
Using a laboratory-scale screening tool working at relevant biofuel process conditions, we assessed the total sugar yields of near-isogenic bmr sorghum mutants with reduced lignin content and their WT under different pretreatment conditions. Deacetylation before dilute acid pretreatment, bmr mutants compared to WT, and the higher temperature of dilute acid pretreatment significantly increased the total sugar yield. These differences decreased as the dilute acid pretreatment temperature increased.
We do not yet understand the ultimate origin of the differences in recalcitrance among the sorghum cultivars tested in this work. There are known differences in the lignin structures of the mutants. The lignin S/G ratio for the bmr12 mutant is ~0.03, for the bmr6 it is ~0.3 and for the wild type it is ~0.6 [24, 25]. However, since we found that the bmr6 mutant rather than the bmr12 mutant was the least recalcitrant of all four cultivars, the S/G ratio is clearly not the controlling factor. More work is needed to understand the structural differences among these mutants causing the differences in measured recalcitrance.
How non-structural carbohydrates are accounted for in the total sugar yield calculation in feedstocks with high non-structural carbohydrates content (e.g., the DE vs. NU calculation) has a modest impact on the calculated yields, with higher calculated yields if they are added to the denominator (DE) of the yield calculation compared to when they are subtracted from the numerator of the yield (NU). However, how non-structural sugars that are solubilized during deacetylation are accounted for in feedstocks with high non-structural carbohydrate content greatly affects the calculated total sugar yield, with the “no-loss” yield calculation providing much higher yields than the “loss” calculation. The choice of calculation should be based on the intended process concept. If the carbohydrates solubilized during deacetylation are not recovered then feedstocks with high non-structural carbohydrates should not undergo deacetylation prior to dilute acid hydrolysis.
The results of the ASE350 small-scale laboratory pretreatment and the larger ZipperClave system showed similar trends for increased total sugar yield with temperature and for the SM bmr mutant compared to the WT. The differences in reactor profile, heating, and heat transfer between the two systems present challenges in accurately mapping smaller systems to larger pretreatment systems.
Methods
Sorghum feedstock samples
The stover was collected from four near-isogenic sorghum lines (S. bicolor L. Moench) (grain heads removed): WT, bmr6 mutant, bmr12 mutant, and stacked (both bmr6 bmr12 mutations) mutant (SM) A Wheatland [26, 27]. The plants were grown in 2012 at the University of Nebraska Field Laboratory, Ithaca, NE (Sharpsburg silty clay loam, fine, smectitic, mesic Typic Argiudoll). Nitrogen fertilizer was applied prior to planting at 112 kg/ha. Individual plots consisted of two 7.6-m rows spaced 76 cm apart. Materials were planted on 17 May, 2012, and a pre-emergent application of atrazine (1.1 kg/ha) was applied on 18 May, 2012. There were five irrigation applications: 9 (3.8 cm), 17 (3.2 cm), 25 (3.2 cm), 30 July (3.2 cm), and 29 August (3.2 cm), 2016. The plots (row) were harvested with a commercial forage harvester (New Holland Model 718) on 10 September, 2012. The samples were oven-dried at 60 °C to less than 10% moisture and milled with a 2 mm screen knife mill (Thomas Scientific, Swedesboro, NJ, USA).
Compositional analysis
The appropriate National Renewable Energy Laboratory (NREL) laboratory analytical procedures (LAP) were used to determine the sugar and organic acid concentrations of the compositional analysis, pretreatment, and enzymatic hydrolysis experiments [28–30]. One exception to these procedures was that (as mentioned above) the samples were oven-dried at 60 °C rather than at or below 45 °C. All samples were dried in the same manner.
The neutral detergent fibers (NDF: weight of the neutral detergent fiber residue corrected for mineral compounds), acid detergent fibers (ADF: weight of the acid detergent fiber residue corrected for mineral compounds), and acid detergent lignin (ADL: weight of the acid detergent lignin residue corrected for mineral compounds) were determined by the Van Soest gravimetric method [31, 32].
The enzymatically digestible organic matter (eDOM) was determined by the De Boever method [33]. The eDOM allows us to assess the digestibility of feedstocks for ruminants. Briefly, samples were incubated, in chronological order, with pepsin in 0.1 M HCl for 24 h at 40 °C, with 0.1 M HCl for 45 min at 80 °C, and with cellulase in an acetate buffer at pH 4.8 for 24 h at 40 °C.
Pretreatment assay
For the smaller bench-scale assay (ASE350 accelerated solvent extractor; Dionex, Sunnyvale, CA, USA), each pretreatment experiment condition was performed in two batches of triplicates for WT and SM, and in two batches of one replicate for bmr6 and bmr12 mutants, except for the experimental conditions of dilute acid pretreatment at 170 and 180 °C, where only one batch of triplicates and one batch of one replicate was done for WT and SM, and for bmr6 and bmr12 mutants, respectively. More replicates have been performed on the WT and SM to be able to assess with more statistical power the difference between the most distinctive analyzed feedstocks.
For the large-scale assay (ZipperClave® reactor), the experiments were performed only for WT and SM. They were performed in three batches of one replicate.
ASE350 acid pretreatment
The smaller bench-scale assay was performed using an ASE350 accelerated solvent extractor (Dionex, Sunnyvale, CA, USA) following the procedure of [7], except that the experiments used 4.0 g of dry biomass and 40 mL of 1% (w/w) sulfuric acid for the dilute acid pretreatment step, and 133 mL of deionized (DI) water for the rinse step. The dry solids loading for the dilute acid pretreatment step remained at approximately 10% (w/w). Briefly, a 66 mL zirconium cell was used as a reaction vessel and the liquor was collected in a 250 mL glass bottle. The pretreatment step consisted of a 7 min heating period followed by 6 min static time at a temperature between 150 and 180 °C, which was fixed depending on the experiment. The cell temperature was then reduced to 100 °C before proceeding to the water rinse step. At the end of the assay, the liquor in the glass bottle was transferred quantitatively to a 200 mL volumetric flask, which was brought to volume with DI water.
The washed solid and an aliquot of the liquor were both transferred in separate 50 mL plastic tubes. They were stored in a refrigerator until further analysis. An aliquot of the liquor was hydrolyzed at 4% (w/w) sulfuric acid for 1 h at 121 °C in an autoclave, neutralized with calcium carbonate, then filtered, and analyzed for total monomeric sugars and organic acids. An aliquot of the washed solid was used to determine its solid content after one night of drying in an oven at 103 °C. This last analysis was started 1 day before the washed solid underwent enzymatic hydrolysis.
This assay uses the total amount of sugars (both in monomeric and oligomeric form) released during pretreatment as part of the total sugar yield. More severe pretreatments typically result in higher monomeric sugar release and lower oligomeric sugar release. Only monomeric sugars are measured after enzymatic hydrolysis; our experience has shown no oligomeric sugars present after the EH assay.
ASE350 deacetylation
The deacetylation assay was also performed using the smaller bench-scale ASE350 accelerated solvent extractor (Dionex, Sunnyvale, CA, USA) in the same configuration as for the dilute acid pretreatment. A 66 mL zirconium cell was used as a reaction cell. It was filled with 4.0 g of biomass and 40 mL of 0.2% (w/w) NaOH. The dry solids loading for the deacetylation pretreatment step was approximately 10% (w/w). This step consisted of a 5 min heating period followed by a 30 min static time at 80 °C. The cell temperature was then brought to 100 °C before an acid rinse step with 67 mL of 0.1% (w/w) sulfuric acid (to neutralize the solid to be able to rinse it efficiently with DI water), followed by a water rinse step with 133 mL of DI water. The liquor was collected in a 250 mL glass bottle. At the end of the assay, the liquor in the glass bottle was transferred quantitatively to a 250 mL volumetric flask that was brought to volume with DI water.
An aliquot of the liquor was transferred in separate 50 mL plastic tubes and stored in a refrigerator until further analysis. An aliquot of the liquor was hydrolyzed at 4% (w/w) sulfuric acid for 1 h at 121 °C in an autoclave and then neutralized, filtered, and analyzed for total monomeric sugars and organic acids. The washed solid was kept in the zirconium cell and stored in a refrigerator until its dilute acid pretreatment. The pretreatment was performed on the washed solid as described above, except that 1.25% sulfuric acid was used to compensate for the water contained in the washed solid (data not shown).
ZipperClave reactor acid pretreatment
Large-scale sorghum pretreatment experiments were conducted in the ZipperClave reactor (Autoclave Engineers, Erie, PA, USA) as previously described [34]. 65.0 g dry weight of sorghum biomass was loaded into the sample container with a 1% (w/w) solution of H2SO4 to achieve a 25% solids loading (w/w). The biomass and acid solution were mixed and set for 5 min prior to pretreatment. The canister was then loaded into the ZipperClave reactor and sealed. Steam was injected using an impeller with lifting edges anchored to the bottom to ensure even heating and mixing of the contents within a removable canister during the reaction. The ZipperClave reactor was equipped with an electrical heating blanket set at the reaction temperature to lessen steam condensation due to heat losses through the reactor wall. Temperature was measured using two thermocouples located in the top and bottom of the reactor. Three reaction temperatures 140, 155, 170 °C for 10 min were used representing severities (R o) of 2.18, 2.62, and 3.06, respectively. After pretreatment, the reactor was depressurized for 20–40 s and vented steam and volatized components recovered as condensate. After the canister was removed, the agitator was rinsed to recover attached solids. The pretreated slurry, recovered from the canister, condensate, and rinsate liquors, were analyzed using standard NREL LAPs [35].
Overall mass recovery after pretreatment was 107.6 ± 2.2%, suggesting a higher bias for solids recovery. Glucose and xylose yields were normalized to 100% solids recovery to adjust for this bias in solids recovery. Total sugar yield for the control corn stover samples was 85.6 ± 3.0 g/g, demonstrating that both pretreatment and enzymatic hydrolysis processes provided robust results.
Enzymatic hydrolysis assay
For all pretreated samples, the enzymatic hydrolysis assay was performed following the procedure of [7], which is based on the NREL LAP enzymatic hydrolysis of lignocellulosic biomass [36]. Briefly, the washed pretreated solid was incubated at 10% (w/w) dry solids with the enzyme (Cellic CTec2, Novozymes, Bagsvaerd, Denmark), the citrate buffer, and DI water for 5 days at 48 °C. The enzyme loading was 20 mg/g total biomass. At the end of the assay, the slurry was transferred quantitatively to a 100 mL volumetric flask and brought to volume with DI water. An aliquot of the flask was then filtered and analyzed for monomeric sugars (Additional files 2, 3, 4, 5).
Data analysis
The raw analytical data were collected and reduced using Microsoft Excel. The open source statistical software R [37] was used to merge the Microsoft Excel files to further analyze and plot the data. All expressions of statistical significance are at the level of 5% (with α = 0.05) assuming independent normal distribution of errors. The statistical assessment of the total sugar yield has only been done on the WT and SM feedstocks because they are made of more replicates and are the most distinctive analyzed feedstocks (Additional files 6, 7, 8, 9).
Abbreviations
- ADF:
-
acid detergent fiber
- ADL:
-
acid detergent lignin
- bmr :
-
brown midrib
- DA:
-
dilute acid
- DE:
-
denominator
- DI:
-
deionized
- EH:
-
enzymatic hydrolysis
- eDOM:
-
enzymatically digestible organic matter
- LAP:
-
laboratory analytical procedure
- LO:
-
loss of the released carbohydrates by deacetylation
- NL:
-
no loss of the released carbohydrates by deacetylation
- NDF:
-
neutral detergent fiber
- NREL:
-
National Renewable Energy Laboratory
- NU:
-
numerator
- PT:
-
pretreatment
- SM:
-
stacked mutant
- TS:
-
total solids
- VS:
-
organic matter (volatile solids)
- WT:
-
wild type
References
Corredor DY, Salazar JM, Hohn KL, Bean S, Bean BW, Wang D. Evaluation and characterization of forage sorghum as feedstock for fermentable sugar production. Appl Biochem Biotechnol. 2009;158:164–79. doi:10.1007/s12010-008-8340-y.
Sattler SE, Funnell-Harris DL, Pedersen JF. Efficacy of singular and stacked brown midrib 6 and 12 in the modification of lignocellulose and grain chemistry. J Agric Food Chem. 2010;58:3611–6.
Saballos A, Ejeta G, Sanchez E, Kang C, Vermerris W. A genomewide analysis of the cinnamyl alcohol dehydrogenase family in sorghum [Sorghum bicolor (L.) Moench] identifies SbCAD2 as the brown midrib 6 gene. Genetics. 2009;181:783–95.
Sattler SE, Saathoff AJ, Haas EJ, Palmer NA, Funnell-Harris DL, Sarath G, et al. A nonsense mutation in a cinnamyl alcohol dehydrogenase gene is responsible for the Sorghum brown midrib 6 phenotype. Plant Physiol. 2009;150:584–95.
Carpita NC, McCann MC. The cell wall. In: Buchanan BB, Gruissem W, Jones R, editors. Biochem Mol Biol Plants. Rockville: American Society Plant Physiologists; 2000. p. 52–109.
Dien BS, Sarath G, Pedersen JF, Sattler SE, Chen H, Funnell-Harris DL, et al. Improved sugar conversion and ethanol yield for forage sorghum (Sorghum bicolor L. Moench) lines with reduced lignin contents. Bioenergy Res. 2009;2:153–64. doi:10.1007/s12155-009-9041-2.
Wolfrum EJ, Ness RM, Nagle NJ, Peterson DJ, Scarlata CJ. A laboratory-scale pretreatment and hydrolysis assay for determination of reactivity in cellulosic biomass feedstocks. Biotechnol Biofuels. 2013;6:162.
Laser M, Larson E, Dale B, Wang M, Greene N, Lynd LR. Comparative analysis of efficiency, environmental impact, and process economics for mature biomass refining scenarios. Biofuels Bioprod Biorefining. 2009;3:247–70.
Humbird D, Tao L, Kinchin C, Hsu D, Aden A, Schoen P, et al. Process design and economics for the conversion of lignocellulosic biomass to ethanol. Golden: NREL; 2010.
Tao L, Aden A, Elander RT, Ramesh V, Lee YY, Garlock RJ, et al. Process and technoeconomic analysis of leading pretreatment technologies for lignocellulosic ethanol production using switchgrass. Bioresour Technol. 2011. doi:10.1016/j.biortech.2011.07.051.
Sousa LD, Chundawat SPS, Balan V, Dale BE. “Cradle-to-grave” assessment of existing lignocellulose pretreatment technologies. Curr Opin Biotechnol. 2009;20:339–47.
Zhao X, Zhang L, Liu D, Chemistry A. Biomass recalcitrance. Part II: fundamentals of different pre-treatments to increase the enzymatic digestibility of lignocellulose. Biofuels Bioprod Biorefining. 2012;6:561–79.
Chen X, Shekiro J, Franden MA, Wang W, Zhang M, Kuhn E, et al. The impacts of deacetylation prior to dilute acid pretreatment on the bioethanol process. Biotechnol Biofuels. 2012;5:8.
Shekiro III J, Kuhn EM, Nagle NJ, Tucker MP, Elander RT, Schell DJ. Characterization of pilot-scale dilute acid pretreatment performance using deacetylated corn stover. Biotechnol Biofuels. 2014;7:23.
Jiang W, Peng H, Li H, Xu J. Effect of acetylation/deacetylation on enzymatic hydrolysis of corn stalk. Biomass Bioenergy. 2014;71:294–8. doi:10.1016/j.biombioe.2014.09.028.
Oliver AL, Pedersen JF, Grant RJ, Klopfenstein TJ, Jose HD. Comparative effects of the sorghum bmr-6 and bmr-12 genes: I. Forage sorghum yield and quality. Crop Sci. 2005;45:2234–9.
Godin B, Lamaudière S, Agneessens R, Schmit T, Goffart J-P, Stilmant D, et al. Chemical composition and biofuel potentials of a wide diversity of plant biomasses. Energy Fuels. 2013;27:2588–98. doi:10.1021/ef3019244.
Godin B, Lamaudière S, Agneessens R, Schmit T, Goffart J-P, Stilmant D, et al. Chemical characteristics and biofuels potentials of various plant biomasses: influence of the harvesting date. J Sci Food Agric. 2013;93:3216–24.
Godin B, Mayer F, Agneessens R, Gerin P, Dardenne P, Delfosse P, et al. Biochemical methane potential prediction of plant biomasses: comparing chemical composition versus near infrared methods and linear versus non-linear models. Bioresour Technol. 2015;175:382–90.
Godin B, Agneessens R, Gerin P, Delcarte J. Lignin in plant biomasses: comparative metrological assessment of the detergent fiber and the insoluble dietary fiber methods. Cellulose. 2015;22:2325–40. doi:10.1007/s10570-015-0656-5.
Wolfrum EJ, Lorenz ÆAJ, Lorenz AJ, DeLeon N. Correlating detergent fiber analysis and dietary fiber analysis data for corn stover collected by NIRS. Cellulose. 2009;16:577–85. doi:10.1007/s10570-009-9318-9.
Godin B, Agneessens R, Goffot S, Lamaudière S, Sinnaeve G, Gerin PA, et al. Revue bibliographique sur les méthodes d’analyse des polysaccharides structuraux des biomasses lignocellulosiques. Biotechnol Agron Soc Environ. 2011;15:165–82.
Godin B, Agneessens R, Gerin P, Delcarte J. Structural carbohydrates in a plant biomass: correlations between the detergent fiber and dietary fiber methods. J Agric Food Chem. 2014;62:5609–16.
Sattler S, Palmer N, Saballos A, Greene A, Xin Z, Sarath G, et al. Identification and characterization of four missense mutations in brown midrib 12 (Bmr12), the caffeic O-methyltranferase (COMT) of sorghum. Bioenergy Res. 2012;5:855–65.
Scully ED, Gries T, Funnell-Harris DL, Xin Z, Kovacs FA, Vermerris W, et al. Characterization of novel brown midrib 6 mutations affecting lignin biosynthesis in sorghum. J Integr Plant Biol. 2016;58:136–49. doi:10.1111/jipb.12375.
Pedersen JF, Funnell DL, Toy JJ, Oliver AL, Grant RJ. Registration of twelve grain sorghum genetic stocks near-isogenic for the brown midrib genes -6 and -12. Crop Sci. 2006;46:491.
Pedersen JF, Toy JJ, Funnell DL, Sattler SE, Oliver AL, Grant RA. Registration of BN611, AN612, BN612, and RN613 sorghum genetic stocks with stacked -6 and -12 genes. J Plant Regist. 2008;2:258.
Hames B, Ruiz R, Scarlata C, Sluiter A, Sluiter J, Templeton D. Preparation of samples for compositional analysis. Lab Anal Proced. 2008. http://www.nrel.gov/docs/gen/fy08/42620.pdf. Accessed 12 Oct 2015.
Templeton DW, Sluiter JB, Ruiz RO, Scarlata CJ, Sluiter AD. Compositional analysis of lignocellulosic feedstocks. 1. Review and description of methods. J Agric Food Chem. 2010;58:9043–53. doi:10.1021/jf1008023.
Templeton DW, Scarlata CJ, Sluiter JB, Wolfrum EJ. Compositional analysis of lignocellulosic feedstocks. 2. Method uncertainties. J Agric Food Chem. 2010;58:9054–62. doi:10.1021/jf100807b.
Van Soest PJ, Wine RH. Use of detergents in the analysis of fibrous feeds. IV. Determination of plant cell-wall constituents. J Assoc Off Anal Chem. 1967;50:50–5.
Van Soest P. Collaborative study of acid-detergent fiber and lignin. J Assoc Off Anal Chem. 1973;56:781–4.
de Boever JL, Cottyn BG, Buysse FX, Wainman FW, Vanacker JM. The use of an enzymatic technique to predict digestibility, metabolizable and net energy of compound feedstuffs for ruminants. Anim Feed Sci Technol. 1986;14:203–14.
Weiss ND, Nagle NJ, Tucker MP, Elander RT. High xylose yields from dilute acid pretreatment of corn stover under process-relevant conditions. Appl Biochem Biotechnol. 2009;155:418–28.
NREL. Standard biomass analytical procedures. Golden: NREL; 2013. http://www.nrel.gov/biomass/analytical_procedures.html. Accessed 12 Oct 2015.
Selig M, Weiss N, Ji Y. Enzymatic saccharification of lignocellulosic biomass laboratory analytical procedure (LAP). Golden: National Renewable Energy Laboratory; 2008. http://www.nrel.gov/biomass/pdfs/42629.pdf. Accessed 12 Oct 2015.
R Core Team. R: a language and environment for statistical computing. Vienna: R Core Team; 2012. http://www.r-project.org. Accessed 12 Oct 2015.
Authors’ contributions
BG and EW conceived the experimental design. BG performed the pretreatment and saccharification experiments. BG performed the data reduction and statistical analysis of all experimental data and drafted the bulk of the manuscript. EW, JD, NN, RA, and SS reviewed the manuscript. All authors read and approved the final manuscript.
Acknowledgements
The authors would like to acknowledge Ryan Ness, Darren Peterson, and John Toy for their technical support.
Competing interests
The authors declare that they have no competing interests.
Availability of data and materials
All datasets supporting the conclusions of this article are included as additional files. The R scripts used to calculate rate data from the primary analytical data in the datasets are also included as additional files.
Funding
This work was supported by the US Department of Energy under Contract No. DE-AC36-08GO28308 with the National Renewable Energy Laboratory. This research was also funded by the Walloon Agricultural Research Center (CRA-W) with the support of the Belgian Science Policy.
Author information
Authors and Affiliations
Corresponding author
Additional files
13068_2016_667_MOESM1_ESM.docx
Additional file 1. Tabular data on total sugar yields. Table S1. ASE350 dilute acid pretreatment yields—NU and DE calculations. Table S2. ASE350 PT-EH yields, with and without deacetylation, DE-NL and DE-LO calculations. Table S3. Zipperclave PT yields–DE calculation.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.
About this article
Cite this article
Godin, B., Nagle, N., Sattler, S. et al. Improved sugar yields from biomass sorghum feedstocks: comparing low-lignin mutants and pretreatment chemistries. Biotechnol Biofuels 9, 251 (2016). https://doi.org/10.1186/s13068-016-0667-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13068-016-0667-y