Abstract
Biomass derived biochar is increasingly recognized as an environmental-friendly sorbent to halt organic pollutants. This study explores the opportunity of managing pine needles waste by converting them into biochar sorbent through catalytic and non-catalytic pyrolysis, carried out at 450 °C. The difference in the biochar yield was not very obvious under catalytic and non-catalytic pyrolysis. The obtained biochars were characterized using X-ray diffraction analysis, energy-dispersive X-ray spectroscopy and scanning electron microscopy. Adsorption of Reactive Black-5 (RB-5) in aqueous solution by produced biochar was studied. The effect of adsorbent dose in batch-mode experiments was investigated. The equilibrium adsorption data of RB-5 were analyzed by Langmuir and Freundlich models. Langmuir isotherms best described the adsorption data with higher correlation coefficient R 2 values (R 2 = 0.983, R 2 = 0.995 and R 2 = 0.941). The maximum RB-5 adsorption capacities q e(mg g−1) of elemental copper and cuprite (Cu–Cu2 O)-based char, magnetite (Fe3O4)-based char and non-catalytically produced char from Langmuir model were 5.40, 2.82 and 4.37 mg g−1, respectively at 0.1 g adsorbent dose. These results indicated that the biochars are suitable to be used as an adsorbent for RB-5 removal.
Similar content being viewed by others
References
Madhusudhana N., Yogendra K., Mahadevan K.M., Naik S.: Photocatalytic degradation of Coralene Dark Red 2-B azo dye using calcium zincate nanoparticle in presence of natural sunlight: an aid to environmental remediation. Int. J. Chem. Eng. Appl. 2, 301–305 (2011)
Daneshvar N., Ayazloo M., Khatae A.R., Pourhassan M.: Biological decolorization of dye solution containing malachite green by microalgae Cosmarium sp. Bioresour. Technol. 98, 1176–1182 (2007)
Afkhami A., Madrakian T., Amini A., Karimi Z.: Effect of the impregnation of carbon cloth with ethylenediaminetetraacetic acid on its adsorption capacity for the adsorption of several metal ions. J. Hazard. Mater. 150, 408–412 (2008)
Robinson T., McMullan G., Marchant R., Nigam P.: Remediation of dyes in textile effluent: a critical review on current treatment technologies with a proposed alternative. Bioresour. Technol. 77, 247–255 (2001)
Grluk M., Hubicki Z.: Kinetics; isotherm and thermodynamic studies of Reactive Black 5 removal by acid acrylic resins. Chem. Eng. J. 162, 919–926 (2010)
Al-Degs Y., Khraisheh M.A.M., Allen S.J., Ahmad M.N.: Effect of carbon surface chemistry on the removal of reactive dyes from textile effluent. Water Res. 34, 927–935 (2000)
Gulnaz O., Kaya A., Dincer S.: The reuse of dried activated sludge for adsorption of reactive dye. J. Hazard. Mater. 134, 190–196 (2005)
Yousefi N., Fatehizadeh A., Azizi E., Ahmadian M., Ahmadi A., Rajabizadeh A., Toolabi A.: Adsorption of Reactive Black 5 dye onto modified wheat straw: isotherm and kinetics study. Sacha J. Environ. Stud. 1, 81–91 (2011)
Yang Y., Lin X., Wei B., Zhao Y., Wang J.: Evaluation of adsorption potential of bamboo biochar for metal-complex dye: equilibrium, kinetics and artificial neural network modeling. Int. J. Environ. Sci. Technol. 11, 1093–1100 (2014)
Heydartaemeh M.R., Ardejani F.D., Badii K., Shabani K.S., Mousavi S.E.: FeCl2/FeCl3 perlite nanoparticles as a novel magnetic material for adsorption of green malachite dye. Arab. J. Sci. Eng. 39, 3383–3392 (2014)
Zhou C., Zhang W., Wang H., Li H., Zhou J., Wang S., Liu J., Luo J., Zou B., Zhou J.: Preparation of Fe3O4-embedded graphene oxide for removal of methylene blue. Arab. J. Sci. Eng. 39, 6679–6685 (2014)
Liu Z., Zhang F., Wu J.: Characterization and application of chars produced from pinewood pyrolysis and hydrothermal treatment. Fuel 89, 510–514 (2010)
Ip A.W.M., Barford J.P., Mckay G.: Reactive Black dye adsorption/desorption onto different adsorbents: effect of salt, surface chemistry, pore size and surface area. J. Colloid Interface Sci. 337, 32–38 (2009)
Heibati B., Rodriguez-Couto S., Amrane A., Rafatullah M., Hawari A., Al-Ghouti M.A.: Uptake of reactive black 5 by pumice and walnut activated carbon: chemistry and adsorption mechanisms. J. Ind. Eng. Chem. 20, 2939–2947 (2014)
Aksu Z.: Application of biosorption for the removal of organic pollutants: a review. Process Biochem. 40, 997–1026 (2005)
Cascarosaa E., Becker J., Ferranteb L., Briens C., Berruti F., Arauzo J.: Pyrolysis of meat-meal and bone-meal blends in a mechanically fluidized reactor. J. Anal. Appl. Pyrolysis 91, 359–367 (2011)
Gopakumar, T.S.; Al-Nadheri, W.M.A.; Jegarajan, D.; Sahu, J.N.; Mubarak, N.M.; Nizamuddin S.: Utilization of palm oil sludge through pyrolysis for bio-oil and bio-char production. Bioresour. Technol. 178, 65–69 (2015)
Pielichowski K., Njuguna J.: Thermal Degradation of Polymeric Materials. Rapra Technology, Shawbury (2005)
Rafatullah M., Ahmad T., Ghazali A., Sulaiman O., Danish M., Hashim R.: Oil palm biomass as a precursor of activated carbons: a review. Crit. Rev. Environ. Sci. Technol. 43, 1117–1161 (2013)
Wang Z., Cao J., Wang J.: Pyrolytic characteristics of pine wood in a slowly heating and gas sweeping fixed-bed reactor. J. Anal. Appl. Pyrolysis 84, 179–184 (2009)
Arami-Niya A., Abnisa F., Sahfeeyan M.S., Wan Daud W.M.A., Sahu J.N.: Optimization of synthesis and characterization of palm shell-based bio-char as a by-product of bio-oil production process. BioResources 7, 246–264 (2012)
Sukiran M.A., Kheang L.S., Bakar N.A., Choo Y.M.: Production and characterization of bio-char from the pyrolysis of empty fruit bunches. Am. J. Appl. Sci. 8, 984–988 (2011)
Li J., Yan R., Xiao B., Liang D.T., Lee D.H.: Preparation of nano-NiO particles and evaluation of their catalytic activity in pyrolyzing biomass components. Energy Fuels 22, 16–23 (2008)
Mamalis A.G.: Recent advances in nanotechnology. J. Mater. Process Technol. 181, 52–58 (2007)
Das S.K., Marsili E.: Bioinspired metal nanoparticle: synthesis, properties and application. In: Rahman, M.M. (ed.) Nanomaterials, pp. 253–274. InTech, Shanghai (2011)
Khalid A., Arshad M., Crowley D.: Decolorization of azo dyes by Shewanella sp. under saline conditions. Appl. Microbiol. Biotechnol. 79, 1053–1059 (2008)
Al-Degs Y.S., El-Barghouthi M.I., El-Sheikh A.H., Walker G.M.: Effect of solution pH, ionic strength, and temperature on adsorption behavior of reactive dyes on activated carbon. Dyes Pigm. 77, 16–23 (2008)
Sensoz S., Angın D.: Pyrolysis of safflower (Charthamus tinctorius L.) seed press cake: part 1. The effects of pyrolysis parameters on the product yields. Bioresour. Technol. 99, 5492–5497 (2008)
Ates F., Sıkdag M.A.: Influence of temperature and alumina catalyst on pyrolysis of corncob. Fuel 88, 1991–1997 (2009)
Sharma R.K., Bakhshi N.N.: Catalytic upgrading of biomass-derived oils to transportation fuels and chemicals. Can. J. Chem. Eng. 69, 1071–1081 (1991)
Cui H.J., Wang M.K., Fu M.L., Ci E.: Enhancing phosphorus availability in phosphorus fertilized zones by reducing phosphate adsorbed on ferrihydrite using rice straw-derived biochar. J. Soils Sediments 11, 1135–1141 (2011)
Wornat M.J., Hurt R.H., Yang N.Y.C., Headley T.J.: Structural and compositional transformations of biomass chars during combustion. Combust Flame 100, 131–143 (1995)
Siddiqui I., Shah M.T., Ahmed I.: X-ray diffraction (XRD) analyses of Thar, Sonda and Meting-Jhimpir coal fields Sindh. Sindh Univ. Res. J. 41, 67–74 (2009)
Cao X., Harris W.: Properties of dairy-manure-derived biochar pertinent to its potential use in remediation. Bioresour. Technol. 101, 5222–5228 (2010)
Borysiak S., Doczekalska B.: Influence of chemical modification of wood on the crystallisation of polypropylene. Eur. J. Wood Wood Prod. 64, 451–454 (2006)
Koyama M., Helbert W., Imai T., Sugiyama J., Henrissat B.: Parallel-up structure evidences the molecular directionality during biosynthesis of bacterial cellulose. Proc. Natl. Acad. Sci. USA 94, 9091–9095 (1997)
Kumar, M.; Gupta, R.C.; Sharma, T.: X-ray diffraction studies of Acacia and eucalyptus wood chars. J. Mater. Sci. 28, 805–810 (1993)
Levendis Y.A., Flagan R.C.: Synthesis, formation and characterization of micro sized glassy carbon spheres of controlled pore structure. Carbon 27, 265–283 (1989)
Kumar S., Loganathan V.A., Gupta R.B., Barnett M.O.: An Assessment of U (VI) removal from ground water using biochar produced from hydrothermal carbonization. J. Environ. Manag. 92, 2504–2512 (2011)
Downie, A.; Crosky, A.; Munroe, P.: Physical properties of biochar. In: Johannes, L.; Joseph, S. Biochar for Environmental Management, Earthscan, Sterling (2009)
Deveci H., Kar Y.: Adsorption of hexavalent chromium from aqueous solutions by biochars obtained during biomass pyrolysis. J. Ind. Eng. Chem. 19, 190–196 (2013)
Onay O.: Influence of pyrolysis temperature and heating rate on the production of bio-oil and char from safflower seed by pyrolysis, using a well-swept fixed-bed reactor. Fuel Process Technol. 88, 523–531 (2007)
Haykiri-Acma H., Ersoy-Mericboyu A., Kucukbayrak S.: Effect of mineral matter of the reactivity of lignite chars. Energy Convers. Manag. 42, 11–20 (2001)
Purevsuren B., Avid B., Tesche B., Davaajav Y.A.: A biochar from casein and its properties. J. Mater. Sci. 38, 2347–2351 (2003)
Mohan D., Rajput S., Singh V.K., Steele P.H., Pittman C.U. Jr.: Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent. J. Hazard. Mater. 18, 319–333 (2011)
Gong R.M., Ding Y., Lie M., Yang C., Liu H.J., Sun Y.Z.: Utilization of powdered peanut hull as biosorbent for removal of anionic dyes from aqueous solution. Dyes Pigm. 64, 187–192 (2005)
Tanyildizi M.S.: Modeling of adsorption isotherms and kinetics of reactive dye from aqueous solution by peanut hull. Chem. Eng. J. 168, 1234–1240 (2011)
Bai R.S., Abraham T.E.: Biosorption of chromium (VI) from aqueous solution by Rhizopus nigricans. Bioresour. Technol. 79, 73–81 (2001)
Deng L., Zhang Y., Qin J., Wang X., Zhu X.: Biosorption of Cr (VI) from aqueous solutions by nonliving green algae Cladophora albida. Miner. Eng. 22, 372–377 (2009)
Zhang G., Qu J., Liu H., Cooper A.T., Wu R.: CuFe2O4/ activated carbon composite: a novel magnetic adsorbent for the removal of acid orange II and catalytic regeneration. Chemosphere 68, 1058–1066 (2007)
Hossein M.A., Behzad H., Reza Y.A., Najmeh V.: Efficiency of reactive Black 5 dye removals and determination of isotherm models in aqueous solution by use activated carbon made of walnut wood. Res. J. Chem. Environ. 16, 26–30 (2012)
Patricia C., Alves F.D., Pitwak M.C.: Adsorption of reactive black 5 from aqueous solution by zeolite from coal fly ash: equilibrium and kinetic studies. Periódico Tchê QuÃmica 8, 17–24 (2011)
Alley E.R.: Water Quality Control Handbook. McGraw Hill, New York (2000)
Mubarak N.M., Kundu A., Sahu J.N., Abdullah E.C., Jayakumar N.S.: Synthesis of palm oil empty fruit bunch magnetic pyrolytic char impregnating with FeCl3 by microwave heating technique. Biomass Bioenergy 61, 265–275 (2014)
Pandolfo A.G., Hollenkamp A.F.: Carbon properties and their role in supercapacitors: review. J. Power Sources 157, 11–27 (2006)
Boehm H.P.: Some aspects of the surface chemistry of carbon blacks and other carbons. Carbon 32, 759–769 (1994)
Qiu Y., Zheng Z., Zhou Z., Sheng G.D.: Effectiveness and mechanisms of dye adsorption on a straw-based biochar. Bioresour. Technol. 100, 5348–5351 (2009)
Namasivayam C., Kavitha D.: Removal of Congo Red from water by adsorption onto activated carbon prepared from coir pith, an agricultural solid waste. Dyes Pigm. 54, 47–58 (2002)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Khan, A., Rashid, A. & Younas, R. Adsorption of Reactive Black-5 by Pine Needles Biochar Produced Via Catalytic and Non-catalytic Pyrolysis. Arab J Sci Eng 40, 1269–1278 (2015). https://doi.org/10.1007/s13369-015-1601-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13369-015-1601-5