Abstract
Knowledge on the dissolution kinetics of β-eut phase in cast Mg AZ91 alloy at temperatures close to the eutectic temperature is very useful for various processes of the alloy. In the present study, dissolution of β-eut phase has been investigated experimentally and considered theoretically. Results have confirmed that the kinetics of β-eut dissolution is basically diffusion controlled. Optimum times for dissolution heat treatment practice of different sizes of cast microstructure which are cooling rate dependant during casting could be suggested based on the present calculation. For fusion welding of the alloy, the present results indicate the difficulty of having a heating rate lower than the critical value (“critical heating rate”) for a significant reduction of the phase to avoid constitutional liquation.
Similar content being viewed by others
References
J.F. King, Magnesium: Commodity or Exotic? Mater. Sci. Technol., 2007, 23(1), p 1–14
L.A. Dobrzanski, T. Tanski, L. Cízek, and Z. Brytan, Structure and Properties of Magnesium Cast Alloys, J. Mater. Process. Technol., 2007, 192–193, p 567–574
T.P. Zhu, Z.W. Chen, and W. Gao, Effects of Microstructure and Partial Melting on Tensile Properties of AZ91 Magnesium Cast Alloy, Mater. Sci. Forum, 2007, 546–549, p 65–68
X. Du and E. Zhang, Microstructure and Mechanical Behaviour of Semi-Solid Die-Casting AZ91D Magnesium Alloy, Mater. Lett., 2007, 61(11–12), p 2333–2337
S. Lun Sin, D. Dubé, and R. Tremblay, An Investigation on Microstructural and Mechanical Properties of Solid Mould Investment Casting of AZ91D Magnesium Alloy, Mater. Charact., 2008, 59(2), p 178–187
H.T. Kang and T. Ostrom, Mechanical Behavior of Cast and Forged Magnesium Alloys and Their Microstructures, Mater. Sci. Eng. A, 2008, 490(1–2), p 52–56
I.A. Yakubtsov, B.J. Diak, C.A. Sager, B. Bhattacharya, W.D. MacDonald, and M. Niewczas, Effects of Heat Treatment on Microstructure and Tensile Deformation of Mg AZ80 Alloy at Room Temperature, Mater. Sci. Eng. A, 2008, 496(1–2), p 247–255
Y.Z. Lü, Q.D. Wang, W.J. Ding, X.Q. Zeng, and Y.P. Zhu, Fracture Behavior of AZ91 Magnesium Alloy, Mater. Lett., 2000, 44(5), p 265–268
S. Kleiner, O. Beffort, A. Wahlen, and P.J. Uggowitzer, Microstructure and Mechanical Properties of Squeeze Cast and Semi-Solid Cast Mg–Al Alloys, J. Light Met., 2002, 2(4), p 277–280
M.M. Avedesian and H. Baker, Magnesium and Magnesium Alloys, ASM International, 1999, p 79
A. Stern and A. Munitz, Partially Melted Zone Microstructural Characterization from Gas Tungsten-Arc Bead on Plate Welds of Magnesium AZ91 Alloy, J. Mater. Sci. Lett., 1999, 18(11), p 853–855
M. Marya and G.R. Edwards, The Laser Welding of Magnesium Alloy AZ91, Weld. World, 2000, 44(2), p 31–37
A. Munitz, C. Cotler, A. Stern, and G. Kohn, Mechanical Properties and Microstructure of Gas Tungsten Arc Welded Magnesium AZ91D Plates, Mater. Sci. Eng. A, 2001, 302(1), p 68–73
M. Marya and G.R. Edwards, Influence of Laser Beam Variables on AZ91D Weld Fusion Zone Microstructure, Sci. Tech. Weld. Join., 2002, 7(5), p 286–293
M. Marya, G.R. Edwards, and S. Liu, An Investigation on the Effects of Gases in GTA Welding of a Wrought AZ80 Magnesium Alloy, Weld. J., 2004, 83(7), p 203s–212s
X. Cao, M. Xiao, M. Jahazi, and J.P. Immarigeon, Continuous Wave ND:YAG Laser Welding of Sand-Cast ZE41A-T5 Magnesium Alloys, Mater. Manuf. Process., 2005, 20(6), p 987–1004
T.P. Zhu, Z.W. Chen, and W. Gao, Incipient Melting in Partially Melted Zone During Arc Welding of AZ91D Magnesium Alloy, Mater. Sci. Eng. A, 2006, 416(1–2), p 246–252
Z.D. Zhang, L.M. Liu, Y. Shen, and L. Wang, Mechanical Properties and Microstructures of a Magnesium Alloy Gas Tungsten Arc Welded with a Cadmium Chloride Flux, Mater. Charact., 2008, 59(1), p 40–46
S. Kou, Welding Metallurgy, 2nd ed., Wiley, New York, 2002, p 321–329
C.H. Cáceres, W.J. Poole, A.L. Bowles, and C.J. Davidson, Section Thickness, Macrohardness and Yield Strength in High-Pressure Diecast Magnesium Alloy AZ91, Mater. Sci. Eng. A, 2005, 402(1–2), p 269–277
C.H. Cáceres, C.J. Davidson, J.R. Griffiths, and C.L. Newton, Effects of Solidification Rate and Ageing on the Microstructure and Mechanical Properties of AZ91 Alloy, Mater. Sci. Eng. A, 2002, 325(1–2), p 344–355
K.A. Hoffmann and S.T. Chiang, Computational Fluid Dynamics, Vol 1, 4th ed., Engineering Education System, Wichita, Kan, 2000, p 63–67
G. Moreau, J.A. Cornet, and D. Calais, Acceleration de la diffusion chimique sous irradiation dans le systeme aluminium-magnesium, J. Nucl. Mater, 1971, 38(2), p 197–202 (in French)
A.K. Dahle, Y.C. Lee, M.D. Nave, P.L. Schaffer, and D.H. St John, Development of the As-Cast Microstructure in Magnesium–Aluminium Alloys, J. Light Met., 2001, 1(1), p 61–72
Y. Wang, B. Sun, Q. Wang, Y. Zhu, and W. Ding, An Understanding of the Hot Tearing Mechanism in AZ91 Magnesium Alloy, Mater. Lett., 2002, 53(12), p 35–39
D. Eskin, Q. Du, D. Ruvalcaba, and L. Katgerman, Experimental Study of Structure Formation in Binary Al-Cu Alloys at Different Cooling Rates, Mater. Sci. Eng. A, 2005, 405(1–2), p 1–10
M. Ohno, D. Mirkovic, and R. Schmid-Fetzer, Liquidus and Solidus Temperatures of Mg-Rich Mg-Al-Mn-Zn Alloys, Acta Mater., 2006, 54(15), p 3883–3891
R.N. Lumley, R.G. Odonnell, D.R. Gunasegaram, and M. Givord, Heat Treatment of High-Pressure Die Castings, Metall. Mater. Trans. A, 2007, 38A(10), p 2564–2574
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhu, T., Chen, Z.W. & Gao, W. Dissolution of Eutectic β-Mg17Al12 Phase in Magnesium AZ91 Cast Alloy at Temperatures Close to Eutectic Temperature. J. of Materi Eng and Perform 19, 860–867 (2010). https://doi.org/10.1007/s11665-009-9539-y
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-009-9539-y