The structure and mechanical properties of aluminum-matrix composites, produced by hot forging of billets consisting of Al and 15 wt.% TiC–20% Al master alloy powder mixture, are investigated. Cylindrical and hollow cone billets are used for forging. It is shown that both strength and hardness of the composites produced from conical billets noticeably exceed those of the materials produced from cylindrical billets. In comparison with cylindrical billets, the use of conical billets for forging leads to an increase in (i) the intensity of deformation and (ii) the microhardness of the matrix phase.
Similar content being viewed by others
References
J. M. Torralba, C. E. da Costa, and F. Velasco, “P/M aluminum matrix composites: an overview,” J. Mat. Process. Techn., 133, 203–206 (2003).
A. Evans, C. Marchi, and A. Mortensen, Metal Matrix Composites in Industry: An Introduction and Survey, Kluver Academic Publishers, Dordrecht, Boston, London 2003, p. 415.
C. R. Selcuk and A. R. Kennedy, “Al–TiC composite made by the addition of master alloy pellets synthesized from reacting elemental powers,” Mat. Letters, 60, 3364–3366 (2006).
G. A. Baglyuk and Yu. A. Shishkina, “New composite dispersion-hardened materials based on aluminum alloys,” Tekhnol. Sistemy, No. 4, 36–43 (2011).
X. C. Tong and A. K. Gosh, “Fabrication of in-situ TiC reinforced aluminum matrix composites,” J. Mat. Sci., 36, 4059–4069 (2001).
P. J. Li, E. G. Kandalova, V. I. Nikitin, et al., “Preparation of Al–TiC composites by self-propagating hightemperature synthesis,” Scripta Mat., 49, 699–703 (2003).
V. C. Srivastava, V. Jindal, and V. Uhlenwinkel, “Hot-deformation behavior of spray-formed 2014 Al + SiCp metal matrix composites,” Mat. Sci. Eng. A., 477, 86–95 (2008).
F. Bardi, M. Cabibbo, E. Evangelista, et al., “An analysis of hot deformation of an Al–Cu–Mg alloy produced by powder metallurgy,” Mat. Sci. Eng. A., 339, 43–52 (2003).
N. Chawla, J. J. Williams, and R. Saha, “Mechanical behavior and microstructure characterization of sinterforged SiC particle reinforced aluminum matrix composites,” J. Light Met., 2, No. 4, 215–227 (2002).
Yu. G. Dorofeev, B. G. Gasanov, V. Yu. Dorofeev, et al., Commercial Process for Hot Forging of Powder Products [in Russian], Metallurgiya, Moscow (1990), p. 206.
A. A. Hendrickson, P. M. Machmeier, and D. W. Smith, “Impact forging of sintered steel preforms,” Powder Met., 43, No. 4, 327–344 (2000).
G. A. Baglyuk, “Effect of deformation parameters on the structure and properties of hot-forged powder materials,” Obrab. Mater. Davl., No. 1 (26), 139–145 (2011).
V. Yu. Dorofeev, “Structure and properties of P/M materials forming during hot forging with elements of extrusion,” Powder Metall. Met. Ceram., 24, No. 7, 523–526 (1985).
V. A. Pavlov and M. I. Nosenko, “Effect of hot working on the formation of structure and properties in sintered metals,” Powder Metall. Met. Ceram., 27, No. 2, 103–107 (1988).
V. Yu. Dorofeev and S. N. Egorov, Inter-Particle Bonding during Formation of Powder Hot-Formed Materials [in Russian], Metalurgizdat, Moscow (2003), p. 152.
Yu. A. Shishkina, G. A. Baglyuk, A. A. Mamonova, and I. B. Tikhonova, “Effect of carbon and aluminum contents on the structurization of Al–Ti–C powder master alloy during reaction synthesis,” Powder Metall. Met. Ceram., 52, Nos. 3–4, 154–160 (2013).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Poroshkovaya Metallurgiya, Vol. 55, Nos. 1–2 (507), pp. 9–17, 2015.
Rights and permissions
About this article
Cite this article
Shishkina, Y.A., Baglyuk, G.A., Kurikhin, V.S. et al. Effect of the Deformation Scheme on the Structure and Properties of Hot-Forged Aluminum-Matrix Composites. Powder Metall Met Ceram 55, 5–11 (2016). https://doi.org/10.1007/s11106-016-9773-4
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11106-016-9773-4