Skip to main content
SpringerLink
Log in

A novel approach towards sustainable electrical discharge machining of metal matrix composites (MMCs)

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

It is a daunting challenge to improve the sustainability of electrical discharge matching (EDM) as well as to make the process environmentally friendly. This paper carried out investigations into the role of steam as a dielectric medium during sink (EDM) of aluminum-based metal matrix composite (MMC) and critically compares the outcome with that of widely used hydrocarbon-based dielectrics such as kerosene in terms of output parameters, positive environmental aspect, and cost-effectiveness. The output parameters such as recast layer, material removal rate (MRR), and machined surface characteristics were analyzed in details. The recast layer obtained upon steam dielectric EDM was significantly improved by 37.15% in terms of thickness, bonding with base metal as well as structure and morphology. This favorable development was attributed towards high temperature, low heat spark material erosion, and low conductivity of steam as a dielectric medium. The machined surface upon steam dielectric EDM apparently contained machined debris rather than solidified molten workpiece material and contributed towards minimum roughness by 1.5 times due to high temperature, high pressure, and low viscosity of the steam. It is found that the ongoing cost of sink EDM can be reduced to one-fifth if the hydrocarbon-based dielectric is replaced by steam.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Pramanik A et al (2018) Accuracy and finish during wire electric discharge machining of metal matrix composites for different reinforcement size and machining conditions. Proc Inst Mech Eng B J Eng Manuf 232(6):1068–1078

    Article  Google Scholar 

  2. Pramanik A, Basak A (2018) Sustainability in wire electrical discharge machining of titanium alloy: understanding wire rupture. J Clean Prod 198:472–479

    Article  Google Scholar 

  3. Pramanik A, Basak A (2016) Degradation of wire electrode during electrical discharge machining of metal matrix composites. Wear 346:124–131

    Article  Google Scholar 

  4. Pramanik A et al (2015) Electrical discharge machining of 6061 aluminium alloy. Trans Nonferrous Metals Soc China 25(9):2866–2874

    Article  Google Scholar 

  5. Mandal A et al (2017) Improvement of surface integrity of Nimonic C 263 super alloy produced by WEDM through various post-processing techniques. Int J Adv Manuf Technol 93(1–4):433–443

    Article  Google Scholar 

  6. Valaki JB, Rathod PP (2016) Assessment of operational feasibility of waste vegetable oil based bio-dielectric fluid for sustainable electric discharge machining (EDM). Int J Adv Manuf Technol 87(5–8):1509–1518

    Article  Google Scholar 

  7. Garg A, Lam JSL (2016) Modeling multiple-response environmental and manufacturing characteristics of EDM process. J Clean Prod 137:1588–1601

    Article  Google Scholar 

  8. Gamage JR et al (2017) Sustainable machining: process energy optimisation of wire electrodischarge machining of Inconel and titanium superalloys. J Clean Prod 164:642–651

    Article  Google Scholar 

  9. Chakraborty S, Dey V, Ghosh S (2015) A review on the use of dielectric fluids and their effects in electrical discharge machining characteristics. Precis Eng 40:1–6

    Article  Google Scholar 

  10. Leão FN, Pashby IR (2004) A review on the use of environmentally-friendly dielectric fluids in electrical discharge machining. J Mater Process Technol 149(1):341–346

    Article  Google Scholar 

  11. Koenig W, Joerres L (1987) Aqueous solutions of organic compounds as dielectrics for EDM sinking. CIRP Annals-Manufacturing Technology 36(1):105–109

    Article  Google Scholar 

  12. Jeswani M (1981) Electrical discharge machining in distilled water. Wear 72(1):81–88

    Article  Google Scholar 

  13. Jilani ST, Pandey P (1984) Experimetnal investigations into the performance of water as dielectric in EDM. International Journal of Machine Tool Design and Research 24(1):31–43

    Article  Google Scholar 

  14. Masuzawa T et al (1983) Water-based dielectric solution for EDM. CIRP Annals-Manufacturing Technology 32(1):119–122

    Article  Google Scholar 

  15. Masaki T, Kuriyagawa T (2009) Study of precision micro-electro-discharge machining(3 rd report)- analysis of micro-EDM process with deionized water. Journal of The Japan Society of Electrical Machining Engineers 43(104):163–171

    Article  Google Scholar 

  16. Vargaftik, N.B., Handbook of physical properties of liquids and gases-pure substances and mixtures. 1975

    Book  Google Scholar 

  17. Chen S, Yan B, Huang F (1999) Influence of kerosene and distilled water as dielectrics on the electric discharge machining characteristics of Ti–6A1–4V. J Mater Process Technol 87(1):107–111

    Article  Google Scholar 

  18. Yu Z, Jun T, Masanori K (2004) Dry electrical discharge machining of cemented carbide. J Mater Process Technol 149(1):353–357

    Article  Google Scholar 

  19. Morash K et al (1994) Measurement of the resistivity of ultrapure water at elevated temperatures. Ultrapure Water 11(9):18–26

    Google Scholar 

  20. Zhang Y et al (2011) Study of the recast layer of a surface machined by sinking electrical discharge machining using water-in-oil emulsion as dielectric. Appl Surf Sci 257(14):5989–5997

    Article  Google Scholar 

  21. Monazzah AH et al (2014) Toughness behavior in roll-bonded laminates based on AA6061/SiCp composites. Mater Sci Eng A 598:162–173

    Article  Google Scholar 

  22. Monazzah AH et al (2017) Al-Mg-Si/SiC laminated composites: fabrication, architectural characteristics, toughness, damage tolerance, fracture mechanisms. Compos Part B 125:49–70

    Article  Google Scholar 

  23. Pouraliakbar H et al (2014) Toughness prediction in functionally graded Al6061/SiCp composites produced by roll-bonding. Ceram Int 40(6):8809–8825

    Article  Google Scholar 

  24. Monazzah AH et al (2015) Toughness enhancement in architecturally modified Al6061-5 vol.% SiCp laminated composites. International Journal of Damage Mechanics 24(2):245–262

    Article  Google Scholar 

  25. Monazzah AH et al (2017) Influence of interfacial adhesion on the damage tolerance of Al6061/SiCp laminated composites. Ceram Int 43(2):2632–2643

    Article  Google Scholar 

  26. Kojima A, Natsu W, Kunieda M (2008) Spectroscopic measurement of arc plasma diameter in EDM. CIRP Annals-Manufacturing Technology 57(1):203–207

    Article  Google Scholar 

  27. Jameson, E.C., Electrical discharge machining. 2001: Society of Manufacturing Engineers

  28. Pramanik A, Littlefair G (2016) Wire EDM mechanism of MMCs with the variation of reinforced particle size. Mater Manuf Process 31(13):1700–1708

    Article  Google Scholar 

  29. Maher I et al (2015) Increasing the productivity of the wire-cut electrical discharge machine associated with sustainable production. J Clean Prod 108:247–255

    Article  Google Scholar 

  30. Syed KH, Palaniyandi K (2012) Performance of electrical discharge machining using aluminium powder suspended distilled water. Turk J Eng Environ Sci 36(3):195–207

    Google Scholar 

  31. Williams E, Smith R (1955) Phenomena accompanying transient low-voltage discharges in liquid dielectrics. I¿ anode phenomena at low currents. Transactions of the American Institute of Electrical Engineers, Part I: Communication and Electronics 74(2):164–169

    Google Scholar 

  32. Jeswani M (1981) Effect of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining. Wear 70(2):133–139

    Article  Google Scholar 

  33. Zhang Y et al (2014) Investigation on the influence of the dielectrics on the material removal characteristics of EDM. J Mater Process Technol 214(5):1052–1061

    Article  Google Scholar 

  34. Pramanik A (2014) Developments in the non-traditional machining of particle reinforced metal matrix composites. Int J Mach Tools Manuf 86:44–61

    Article  Google Scholar 

  35. Yanagida D, Minami H, Watanabe K (2016) Electrical discharge machining of PCD in ultrapure water. Procedia CIRP 42:292–296

    Article  Google Scholar 

  36. Pramanik A, Basak A, Islam MN (2015) Effect of reinforced particle size on wire EDM of MMCs. Int J Mach Mach Mater 17(2):139–149

    Google Scholar 

  37. Gamage JR et al (2016) Process level environmental performance of electrodischarge machining of aluminium (3003) and steel (AISI P20). J Clean Prod 137:291–299

    Article  Google Scholar 

  38. Yip W, S. To (2018) Sustainable manufacturing of ultra-precision machining of titanium alloys using a magnetic field and its sustainability assessment. Sustain Mater Technol 16:38–46

    Google Scholar 

  39. Banerjee N, Sharma A (2018) A comprehensive assessment of minimum quantity lubrication machining from quality, production, and sustainability perspectives. Sustain Mater Technol 17:e00070

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Indian Institute of Technology (ISM), Sardar Patel Nagar, Dhanbad, Jharkhand, 826004, India

    K. Paswan & S. Chattopadhyaya

  2. Department of Mechanical Engineering, Curtin University, Bentley, WA, 6102, Australia

    A. Pramanik

  3. Adelaide Microscopy, The University of Adelaide, Adelaide, Australia

    A. K. Basak

Authors
  1. K. Paswan
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. Pramanik
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. Chattopadhyaya
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. K. Basak
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. Pramanik.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Paswan, K., Pramanik, A., Chattopadhyaya, S. et al. A novel approach towards sustainable electrical discharge machining of metal matrix composites (MMCs). Int J Adv Manuf Technol 106, 1477–1486 (2020). https://doi.org/10.1007/s00170-019-04816-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-019-04816-6

Keywords

Search

Navigation