Abstract
In this study, 20-mm-thick 7075-T6 aluminum alloy plates were joined by friction stir welding, and the temperature field, microstructure evolution, and mechanical properties of the joint along the thickness were investigated. The temperature profiles in different zones of the weld were measured by designing various thermocouple layouts. Fine dynamic recrystallized structures in the nugget zone (NZ) were observed, and different grain sizes were estimated by electron back scattering diffraction (EBSD) along the thickness. Also, the precipitate distributions and types in different locations were characterized by scanning electron microscope (SEM) and transmission electron microscopy (TEM) techniques. Vickers microhardness was measured across different cross sections of the weld. Moreover, the results of tensile properties showed that the slice in the middle-upper had the highest ultimate tensile, yield strength, and elongation compared to other slices. Most of the failures for the joints presented a ductile fracture. All results were consistent with a temperature gradient along the thickness during friction stir welding (FSW).
Similar content being viewed by others
References
Rajakumar S, Muralidharan C, Balasubramanian V (2011) Influence of friction stir welding process and tool parameters on strength properties of AA7075-T6 aluminium alloy joints. Mater Des 32:535–549
Rometsch PA, Zhang Y, Knight S (2014) Heat treatment of 7xxx series aluminium alloys-Some recent developments. Trans Nonferrous Met Soc China 24:2003–2017
Feng AH, Chen DL, Ma ZY (2010) Microstructure and cyclic deformation behavior of a friction-stir- welded 7075 Al alloy. Metall Mater Trans A 41:957–971
Dehghani K, Ghorbani R, Soltanipoor AR (2015) Microstructural evolution and mechanical properties during the friction stir welding of 7075-O aluminum alloy. Int J Adv Manuf Tech 77:1671–1679
Fuller CB, Mahoney MW, Calabrese M, Micona L (2010) Evolution of microstructure and mechanical properties in naturally aged 7050 And 7075 Al friction stir welds. Mater Sci Eng A 527:2233–2240
Balasubramanian V, Ravisankar V, Madhusudhan RG (2008) Effect of post weld aging treatment on fatigue behavior of pulsed current welded AA7075 aluminum alloy joints. J Mater Eng Perform 7:224–233
Lotfi AH, Nourouzi S (2014) Predictions of the optimized friction stir welding process parameters for joining AA7075-T6 aluminum alloy using preheating system. Int J Adv Manuf Tech 73:1717–1737
Genevois C, Deschamps A, Denquin A, Doisneau-coottignies B (2005) Quantitative investigation of precipitation and mechanical behaviour for AA2024 friction stir welds. Acta Mater 53:2447–2458
Sharma C, Dwivedi DK, Kumar P (2013) Effect of post weld heat treatments on microstructure and mechanical properties of friction stir welded joints of Al-Zn-Mg alloy AA7039. Mater Des 43:134–143
Scialpi A, DeFilippis LAC, Cavaliere P (2007) Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy. Mater Des 28:1124–1129
Ghetiya ND, Patel KM, Patel Anup B (2015) Prediction of temperature at weld line in air and immersed friction stir welding and its experimental validation. Int J Adv Manuf Technol 79:1239–1246
Khandkar MZH, Khan JA, Reynolds AP (2003) Prediction of temperature distribution and thermal history during friction stir welding: input torque based model. Sci Technol Weld Joining 8:165–174
Su JQ, Nelson TW, Sterling CJ (2005) Microstructure evolution during FSW/FSP of high strength aluminum alloys. Mater Sci Eng A 405:277–286
Ji SD, Jin YY, Yue YM, Gao SS, Huang YX, Wang L (2013) Effect of temperature on material transfer behavior at different stages of friction stir welded 7075-T6 aluminum alloy. J Mater Sci Technol 29(10):955–960
Li WY, Li JF, Zhang ZH, Gao DL, Chao YJ (2013) Metal flow during friction stir welding of 7075-T651 aluminum alloy. Exp Mech 53(9):1573–1582
Sharma C, Dwivedi DK, Kumar P (2012) Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy. Mater Des 36:379–390
Fujii H, Cui L, Maeda M, Nogi K (2006) Effect of tool shape on mechanical properties and microstructure of friction stir welded aluminum alloys. Mater Sci Eng A 419:25–31
Lim S, Kim S, Lee CG, Kim SJ (2005) Mechanical properties of friction stir welded Al alloys with different hardening mechanisms. Met Mater Int 11(2):113–120
Xu WF, Liu JH, Luan GH, Dong CL (2009) Temperature evolution, microstructure and mechanical properties of friction stir welded thick 2219-O aluminum alloy joints. Mater Des 30:1886–1893
Canaday Clinton T, Moore Matthew A, Tang W, Reynolds AP (2013) Through thickness property variations in a thick plate AA7050 friction stir welded joint. Mater Sci Eng A 559:678–682
Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng R 50:1–78
Xing L, Ke LM, Liu GP, Huang FA (2002) Microstructure and mechanical properties of a friction stir welded LD10 aluminum. Trans China Weld I 23(6):55–58 (in Chinses)
Michael BP, Thomas GH, John AB, Richard JL, David MB, Robert JS (2006) Residual stress measurements in a thick, dissimilar aluminum alloy friction stir weld. Acta Mater 54:4013–4021
Mao YQ, Ke LM, Liu FC, Liu Q, Huang CP, Xing L (2014) Effect of tool pin eccentricity on microstructure and mechanical properties in friction stir welded 7075 aluminum alloy thick plate. Mater Des 62:334–343
Prangnell PB, Heason CP (2005) Grain structure formation during friction stir welding observed by the ‘stop action technique. Acta Mater 53:3179–3192
Fonda RW, Knipling KE, Bingert JF (2007) Microstructural evolution ahead of the tool in aluminum friction stir welds. Scripta Mater 58:343–348
Buffa G, Fratini L, Shivpuri R (2007) CDRX modelling in friction stir welding of AA7075-T6 aluminum alloy: analytical approaches. J Mater Process Tech 191:356–359
McNelley TR, Swaminathan S, Su JQ (2008) Recrystallization mechanisms during friction stir welding/ processing of aluminum alloys. Scripta Mater 58:349–354
Jata KV, Sankaran KK, Ruschau J (2000) Friction stir welding effects on microstructure and fatigue of aluminum alloy 7050-T7451. Metall Mater Trans A 31:2181–2192
Jiang XJ, Tafto J, Noble B, Holme B, Waterloo G (2000) Differential scanning calorimetry and electron diffraction investigation on low-temperature aging in Al-Zn-Mg alloys. Metall Mater Trans A 31:339–348
Sato YS, Urata M, Kokawa H, Ikeda K (2003) Hall–Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys. Mater Sci Eng A 354:298–305
Mahoney MW, Rhodes CG, Flintoff JG, Bingel WH, Spurling RA (1998) Properties of friction-stir-welded 7075 T651 aluminum. Metall Mater Trans A 29:1955–1964
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yuqing, M., Liming, K., Fencheng, L. et al. Investigations on temperature distribution, microstructure evolution, and property variations along thickness in friction stir welded joints for thick AA7075-T6 plates. Int J Adv Manuf Technol 86, 141–154 (2016). https://doi.org/10.1007/s00170-015-8182-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-8182-z