Skip to main content
SpringerLink
Log in

Spray parameters and particle behavior relationships during plasma spraying

  • Published:
Journal of Thermal Spray Technology Aims and scope Submit manuscript

Abstract

Using laser anemometry, laser fluxmetry, and statistical two-color pyrometry, the velocity, number flux, and surface temperature distributions of alumina and zirconia particles in dc plasma jets have been determined inflight for various spraying parameters. The flux measurements emphasized the importance of the carrier gas flow rate, which must be adjusted to the plasma jet momentum depending on the arc current, nozzle diameter, gas flow rate, and gas nature. It has also been shown that the particle trajectories depend both on the particle size and injection velocity distributions and that the position and tilting of the injector plays a great role. The particle size drastically influences its surface temperature and velocity, and for the refractory materials studied, only the particles below 45 μm in diameter are fully molten in Ar-H2 (30 vol%) plasma jets at 40 kW. The morphology of the particles is also a critical parameter. The agglomerated particles partially explode upon penetration into the jet, and the heat propagation phenomenon is seriously enhanced, particularly for particles larger than 40 μm. The effects of the arc current and gas flow rate have been studied, and the results obtained in an air atmosphere cannot be understood without considering the enhanced pumping of air when the plasma velocity is increased. The Ar-He (60 vol%) and Ar-H2 (30 vol%) plasma jets, when conditions are found where both plasma jets have about the same dimensions, do not result in the same treatment for the particles. The particles are not as well heated in the Ar-He jet compared to the Ar-H2 jet. Where the surrounding atmosphere is pure argon instead of air (in a controlled atmosphere chamber), he radial velocity and temperature distributions are broadened, and if the velocities are about the same, the temperatures are higher. The use of nozzle shields delays the air pumping and increases both the velocity and surface temperature of the particles. However, the velocity increase in this case does not seem to be an advantage for coating properties.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. N.N. Rykalin and V.V. Kudinov, Plasma Spraying,Pure Appl. Chem., Vol 48, 1976, p 229–239

    CAS  Google Scholar 

  2. J.H. Zaat, Thermal Spraying,Ann. Rev. Mater. Sci., Vol 13, 1983, p 9–42

    Article  CAS  Google Scholar 

  3. Thermal Spraying, Practice, Theory and Applications, American Welding Society, 1985

  4. Technology Forecast,Adv. Mater. Proc, Vol 30, 1988

  5. P. Fauchais, A. Grimaud, A. Vardelle, and M. Vardelle, Plasma Spraying: A Review,Ann.Phys. Fr., Vol 14, 1989, p 261–310

    Article  CAS  Google Scholar 

  6. P. Fauchais, J.F. Coudert, A. Vardelle, M. Vardelle, and A. Denoirjean, Diagnostics of Thermal Spraying Plasma Jets,J. Thermal Spray Technol., Vol 1 (No. 2), 1992, p 117–128

    Article  CAS  Google Scholar 

  7. P. Fauchais, J.F. Coudert, and M. Vardelle, Diagnostics in Thermal Plasma Processing, inPlasma Diagnostics, Academic Press, 1989, p 349–446

  8. L. Gyenis, A. Grimaud, O. Betoule, F. Monerie-Moulin, P. Fauchais, and M. Ducos, “Influence of Temperature Control during Spraying on Hardness and Cohesion of Alumina Coatings,” Proc. 2nd Plasma Technik Symposium, Vol 1, S. Blum-Sandmeier, H. Eschnauer, P. Huber, and A.R. Nicoll, Ed., Wohlen, Switzerland, 1991, p 95–101

  9. M. Vardelle, “Study of Heat, Mass and Momentum Transfers Between A dc Plasma Jet and Powders,” State thesis, University of Limoges, France, July, 1987

    Google Scholar 

  10. M. Vardelle, A. Vardelle, and P. Fauchais,“Experimental Study of the Thermal Exposure Experienced by Powders under Plasma Spraying Conditions in Air and Inert Environment,” Proc. 1st Plasma Technik Symposium, Vol 2, P. Huber and H. Eschnauer, Ed., Wohlen, Switzerland, 1988, p 167–178

  11. E. Pfender, Particle Behavior in Thermal Plasmas,Plasma Chem. Plasma Proc, Vol 9, 1989, p 167S-194S

    Article  CAS  Google Scholar 

  12. E. Bourdin, P. Fauchais, and M.I. Boulos, Transient Heat Conduction under Plasma Conditions,Int. J. Heat Mass Transfer, Vol 26, 1983, p 567–582

    Article  CAS  Google Scholar 

  13. G. Schweir, Plasma Spray Powders for TBCs,Advances in Thermal Spraying, Pergamon Press, 1986, p 277–286

  14. B.A. Kusher, S. Rangaswany, and A.J. Rotolico,“Thermal Spray Powders: Manufacturing Methods and Quality Control Procedures,” Proc. 1st Plasma Technik Symposium, Vol 2, P. Huber and H. Eschnauer, Ed., Wohlen, Switzerland, 1988, p 191–202

  15. M. Vardelle, A. Vardelle, A. Denoirjean, and P. Fauchais, Heat Treatment of Zirconia Powders with Different Morphologies under Thermal Plasma Conditions,Mater. Res. Soc. Symp. Proc, MRS, 190, 1991, p 175–183

    CAS  Google Scholar 

  16. D. Bernard,“Plasma Spraying of TBCs,” Ph.D. thesis, University of Limoges, France, June 1990

    Google Scholar 

  17. E. Lugsheider, I. Rass, H.L. Heijnen, P. Chandler, T. Cosak, P. Fauchais, A. Denoirjean, and A. Vardelle, Comparison of the Coatings Properties of Different Types of Powder Morphologies,Thermal Spray: International Advances in Coatings Technology, C.C. Berndt, Ed., ASM International, 1992, p 967–973

  18. R. Spores, E. Pfender, Flow Structure of A Turbulent Thermal Plasma Jet,Surf. Coat. Technol, Vol 37, 1989, p 251–260

    Article  Google Scholar 

  19. Ph. Roumilhac, J.F. Coudert, and P. Fauchais, Influence of the Arc Chamber Design on the Characteristics and Temperature Distributions of Ar-H2 and Ar-He Spraying Plasma Jets,Mater. Res. Soc. Symp. Proc, MRS, 190, 1991, p227–238

    CAS  Google Scholar 

  20. B. Pateyron, F. Elchinger, G. Delluc, and P. Fauchais, Thermodynamic and Transport Properties of Ar-H2 and Ar-He Plasma Gases Used for Spraying at Atmospheric Pressure,Plasma Chem. Plasma Proc, Vol 12 (No. 4), 1992, p 421–448

    Article  CAS  Google Scholar 

  21. Ph. Roumilhac, M. Vardelle, A. Vardelle, and P. Fauchais, Comparison of Heat and Momentum Transfer to Ceramic Particles Sprayed in Ar-He and Ar-H2 at Atmospheric Pressure,Thermal Spray Technology: New Ideas and Processes, D.L. Houck, Ed., ASM International, 1989, p 111–116

  22. M. Vardelle, A. Vardelle, Ph. Roumilhac, and P. Fauchais, Influence of the Surrounding Atmosphere under Plasma Spraying Conditions,Thermal Spray Technology: New Ideas and Processes, D.L. Houck, Ed., ASM International, 1989, p 117–121

Download references

Author information

Authors and Affiliations

  1. Laboratoire Matériaux Céramiques et Traitements de Surface, University of Limoges, France

    M. Vardelle, A. Vardelle & P. Fauchais

Authors
  1. M. Vardelle
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. Vardelle
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. P. Fauchais
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Vardelle, M., Vardelle, A. & Fauchais, P. Spray parameters and particle behavior relationships during plasma spraying. JTST 2, 79–91 (1993). https://doi.org/10.1007/BF02647426

Download citation

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF02647426

Key words

Search

Navigation