Abstract
In the present chapter the general features of thermodynamically based constitutive modeling are described. In such approach a basic hypothesis is that the state of a material is entirely determined by certain values of some independent variables, called variables of state. This type of constitutive modeling is particularly well adapted to the formulation of constitutive equations for deformable solids with several dissipative phenomena. A common three-stage procedure in the definition of a constitutive model is discussed: (1) choice of the state variables, (2) definition of the state potential from which the state relations (between strain-like variables and their dual conjugated forces) are derived, and (3) choice of the dissipation potential from which the rate equations of state variables are derived. The classification of constitutive equations is then presented for elastic-damage, elastic-plastic, thermo-elastic-(visco)plastic, and elastic-plastic-damage materials. Damage-induced anisotropy and unilateral damage effect are accounted. When plasticity is considered, an alternative multiscale approach, based on polycrystalline calculations for the description of yielding anisotropy and its evolution with accumulated deformation, is also discussed. As an example of thermoplastic coupling, the fatigue behavior of martensitic hot work tool steel in nonisothermal conditions is analyzed. In this example two cases are compared: (1) partial coupling, when changing temperature is accounted only in changing material parameters, and (2) full coupling, when additional terms proportional to temperature rate are added in the kinetic equations of thermodynamic conjugate forces. Numerical simulations are performed, which indicate the significant influence of temperature rate on the response of constitutive model when cyclic thermomechanical loading is considered.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Aboudi, J.: The effect of anisotropic damage evolution on the behavior of ductile and brittle matrix composites. Int. J. Solids Struct. 48(14–15), 2102–2119 (2011)
Abu Al-Rub, R.K., Darabi, M.K.: A thermodynamic framework for constitutive modeling of time-and rate-dependent materials, part I: theory. Int. J. Plast. 34, 61–92 (2012)
Abu Al-Rub, R.K., Voyiadjis, G.Z.: On the coupling of anisotropic damage and plasticity models for ductile materials. Int. J. Solids Struct. 40, 2611–2643 (2003)
Barlat, F., Brem, J.C., Yoon, J.W., Chung, K., Dick, R.E., Lege, D.J., Pourboghrat, F., Choi, S.-H., Chu, E.: Plane stress function for aluminium alloy sheets—part I: theory. Int. J. Plast. 19, 1297–1319 (2003)
Barlat, F., Aretz, H., Yoon, J.W., Karabin, M.E., Brem, J.C., Dick, R.E.: Linear transformation-based anisotropic yield functions. Int. J. Plast. 21, 1009–1039 (2005)
Barlat, F., Gracio, J.J., Lee, M.-G., Rauch, E.F., Vincze, G.: An alternative to kinematic hardening in classical plasticity. Int. J. Plast. 27, 1309–1327 (2011)
Bednarek, Z., Kamocka, R.: The heating rate impact on parameters characteristic of steel behaviour under fire conditions. J. Civ. Eng. Manag. 12(4), 269–275 (2006)
Benallal, A., Bigoni, D.: Effects of temperature and thermo-mechanical couplings on material instabilities and strain localization of inelastic materials. J. Mech. Phys. Solids 52, 725–753 (2004)
Bernhart, G., Moulinier, G., Brucelle, O., Delagnes, D.: High temperature low cycle fatigue behaviour of a martensite forging tool steel. Int. J. Fatigue 21(2), 179–186 (1999)
Blaj, L., Cailletaud, G.: Application of a multimechanism model to the prediction of ratcheting behavior. In: Miannay, D., Costa, P., François, D. (eds.) Advances in Mechanical Behaviour, Plasticity and Damage, SF2M, vol. 2, pp. 1155–1160 (2000)
Boudifa, M., Saanouni, K., Chaboche, J.L.: A micromechanical model for inelastic ductile damage prediction in polycrystalline metals for metal forming. Int. J. Mech. Sci. 51, 453–464 (2009)
Cailletaud, G., Saï, K.: Study of plastic/viscoplastic models with various inelastic mechanisms. Int. J. Plast. 11, 991–1005 (1995)
Casey, J.: On elastic-thermo-plastic materials at finite deformations. Int. J. Plast. 14, 173–191 (1998)
Cazacu, O., Barlat, F.: A criterion for description of anisotropy and yield differential effects in pressure-insensitive materials. Int. J. Plast. 20, 2027–2045 (2004)
Cazacu, O., Plunkett, B., Barlat, F.: Orthotropic yield criterion for hexagonal closed packed metals. Int. J. Plast. 22, 1171–1194 (2006)
Chaboche, J.L.: A review of some plasticity and viscoplasticity constitutive theories. Int. J. Plast. 24, 1642–1693 (2008)
Chaboche, J.L., Kruch, S., Maire, J.F., Pottier, T.: Towards a micromechanics based inelastic and damage modeling of composites. Int. J. Plast. 17, 411–439 (2001)
Chaboche, J.L.: Thermodynamic formulation of constitutive equations and application to the viscoplasticity and viscoelasticity of metals and polymers. Int. J. Solids Struct. 34(18), 2239–2254 (1997)
Chaboche, J.L.: Viscoplastic constitutive equations for the description of cyclic and anisotropic behaviour of metals. Bulletin de L’Academie Polonaise des Sciences. Série des Sciences Techniques XXV(1), 33–39 (1997)
Chaboche, J.L.: Time independent constitutive theories for cyclic plasticity. Int. J. Plast. 2(2), 149–188 (1986)
Chaboche, J.L., Rousselier, G.: On the plastic and viscoplastic constitutive equations, parts I and II. J. Press. Vessel Technol., ASME 105, 153–164 (1983)
Challamel, N., Lanos, C., Casandjian, C.: Strain-based anisotropic damage modeling and unilateral effects. Int. J. Mech. Sci. 47, 459–473 (2005)
Chen, X.F., Chow, C.L.: On damage strain energy release rate Y. Int. J. Damage Mech. 4, 236–251 (1995)
Chow, C.L., Lu, T.J.: An analytical and experimental study of mixed-mode ductile fracture under nonproportional loading. Int. J. Damage Mech. 1, 191–236 (1992)
Egner, H.: Non-isothermal coupled thermo-damage-plasticity. In: Hetnarski, R. (ed.) Encyclopedia of Thermal Stresses, pp. 3356–3368. Springer, Berlin (2014)
Egner, H.: On the full coupling between thermo-plasticity and thermo-damage in thermodynamic modeling of dissipative materials. Int. J. Solids Struct. 49, 279–288 (2012)
Egner, H., Egner, W.: Modeling of a tempered martensitic hot work tool steel behavior in the presence of thermo-viscoplastic coupling. Int. J. Plast. 57, 77–91 (2014)
Egner, H., Egner, W.: Modeling of coupled dissipative phenomena in engineering materials. In: Altenbach, H., Kruch, S. (eds.) Advanced Materials Modeling for Structures. Series Advanced Structured Materials, vol. 19, pp. 141–151. Springer, Berlin (2013)
Ganczarski, A.: Thermal anisotropy inducing brittle damage. Tech. Mech. 19, 321–330 (1999)
Ganczarski, A.W., Egner, H., Muc, A., Skrzypek, J.J.: Constitutive models for analysis and design of multifunctional technological materials. In: Rustichelli, F., Skrzypek, J.J. (eds.) Innovative Technological Materials. Structural Properties by Neutrons, Synchrotron Radiation and Modelling, pp. 179–220. Springer, New York (2010)
Ganczarski, A., Skrzypek, J.J.: A study on coupled thermo-elasto-plastic-damage dissipative phenomena: models and application to some innovative materials. J. Therm. Stress. 32, 698–751 (2009)
Ganczarski, A., Skrzypek, J.: Mechanics of Novel Materials (in Polish). Wydawnictwo Politechniki Krakowskiej, Kraków (2013)
Gibbons, C.L., Dunn, J.E.: Investigations of reduced service life of hot work (Cr-Mo) die steel pieces. Ind. Heat. 47, 6–9 (1980)
Golański, G., Mroziński, S.: Low cycle fatigue and cyclic softening behavior of martensitic cast steel. Eng. Fail. Anal. 35, 692–702 (2013)
Golański, G., Mroziński, S.: Fatigue life at \(550\,^{\circ }\)C temperature of aged martensitic cast steel. AASRI Procedia 2, 249–255 (2013)
Halphen, B., Nguyen, Q.S.: Sur les matériaux standards généralisés. Journal de Méchanique 14, 39–63 (1975)
Hartmann, G.: Comparison of the uniaxial behavior of the inelastic constitutive models of Miller and Walker by numerical experiments. Int. J. Plast. 6, 189–206 (1990)
Hershey, A.V.: The plasticity of an isotropic aggregate of anisotropic face centered cubic crystals. J. Appl. Mech. 21, 241–249 (1954)
Houlsby, G.T., Puzrin, A.M.: A thermomechanical framework for constitutive models for rate-independent dissipative materials. Int. J. Plast. 16, 1017–1047 (2000)
Jiang, Y., Zhang, J.: Benchmark experiments and characteristic cyclic plasticity deformation. Int. J. Plast. 24, 1481–1515 (2008)
Khan, A.S., Liu, H.: Strain rate and temperature dependent fracture criteria for isotropic and anisotropic metals. Int. J. Plast. 37, 1–15 (2012)
Khan, A.S., Yu, S., Liu, H.: Deformation enhanced anisotropic responses of Ti-6Al-4V alloy, part II: a stress rate and temperature dependent anisotropic yield criterion. Int. J. Plast. 38, 14–26 (2012)
Kowalsky, U., Ahrens, H., Dinkler, D.: Distorted yield surfaces-modelling by higher order anisotropic hardening tensors. Comput. Mater. Sci. 16, 81–88 (1999)
Krajcinovic, D.: Constitutive theory of damaging materials. ASME J. Appl. Mech. 50, 355–360 (1983)
Kuo, Ch.-M., Lin, Ch.-S.: Static recovery activation energy of pure copper at room temperature. Scripta Materialia 57, 667–670 (2007)
Lebensohn, R.A., Tome, C.N.: A self-consistent anisotropic approach for the simulation of plastic deformation and texture development of polycrystals: application to zirconium alloys. Acta Metall. Mater. 41, 2611–2624 (1993)
Lee, K.D., Krempl, E.: An orthotropic theory of viscoplasticity based on overstress for thermomechanical deformation. Int. J. Solids Struct. 27, 1445–1459 (1991)
Lemaitre, J., Chaboche, J.L.: Mechanics of Solid Materials. Cambridge University Press, London (1990)
Litewka, A.: Effective material constants for orthotropically damaged elastic solids. Arch. Mech. Stos. 37(6), 631–642 (1985)
McDowell, D.L.: A nonlinear kinematic hardening theory for cyclic thermoplasticity and thermoviscoplasticity. Int. J. Plast. 8, 695–728 (1992)
Mebarki, N., Delagnes, D., Lamesle, P., Delmas, F., Levaillant, C.: Relationship between microstructure and mechanical properties of a 5%Cr tempered martensitic tool steel. Mater. Sci. Eng. A 387–389(1–2), 171–175 (2004)
Mirzakhani, B., Salehi, M.T., Khoddam, S., Seyedin, S.H., Aboutalebi, M.R.: Investigation of dynamic and static recrystallization behavior during thermomechanical processing in a API-X70 microalloyed steel. J. Mater. Eng. Perform. 18(8), 1029–1034 (2009)
Moreno, V., Jordan, E.H.: Prediction of material thermomechanical response with a unified viscoplastic constitutive model. Int. J. Plast. 2, 223–245 (1986)
Murakami, S., Ohno, N.: A continuum theory of creep and creep damage. In: Ponter, A.R.S., Hayhurst, D.R. (eds.) Creep in Structures, 3rd IUTAM Symposium on Creep in Structures, pp. 422–444. Springer, Berlin (1981)
Nixon, M.E., Cazacu, O., Lebensohn, R.A.: Anisotropic response of high-purity \(\alpha \)-titanium: experimental characterization and constitutive modeling. Int. J. Plast. 26, 516–532 (2010)
Ohno, N.: Recent topics in constitutive modeling for cyclic plasticity and viscoplasticity. Appl. Mech. Rev. 43(11), 283–295 (1990)
Ohno, N., Takahashi, Y., Kubawara, K.: Constitutive modeling of anisothermal cyclic plasticity of 304 stainless steel. J. Eng. Mater. Technol. 111, 106–114 (1989)
Onsager, L.: Reciprocal relations in irreversible thermodynamics I. Phys. Rev. 37, 405–426 (1931)
Onsager, L.: Reciprocal relations in irreversible thermodynamics II. Phys. Rev. 38, 2265–2279 (1931)
Ottosen, N.S., Ristinmaa, M.: The Mechanics of Constitutive Modeling. Elsevier, Amsterdam (2005)
Phillips, A., Tang, J.L.: The effect of loading path on the yield surface at elevated temperatures. Int. J. Solids Struct. 8, 463–474 (1972)
Plunkett, B., Lebensohn, R.A., Cazacu, O., Barlat, F.: Anisotropic yield function of hexagonal materials taking into account texture development and anisotropic hardening. Acta Mater. 54, 4159–4169 (2006)
Plunkett, B., Cazacu, O., Lebensohn, R.A., Barlat, F.: Elastic-viscoplastic modeling of textured metals and validation using the Taylor cylinder impact test. Int. J. Plast. 23, 1001–1021 (2007)
Plunkett, B., Cazacu, O.: Viscoplastic modeling of anisotropic textured metals. In: Cazacu, O. (ed.) Multiscale Modeling of Heterogeneous Materials: From Microstructure to Macro-Scale Properties, pp. 111–126. ISTE/Wiley, New York (2008)
Plunkett, B., Cazacu, O., Barlat, F.: Orthotropic yield criteria for description of the anisotropy in tension and compression of sheet metal. Int. J. Plast. 24, 847–866 (2008)
Prager, W.: Non-isothermal plastic deformation. In: Proceedings, Konnickl Nederl. Akademie Van Wetenschappen Te Amsterdam, Series B, vol. 61 (1958)
Saanouni, K.: Damage Mechanics in Metal Forming, Advanced Modeling and Numerical Simulation. Wiley, London (2012)
Saï, K.: Multi-mechanism models: present state and future trends. Int. J. Plast. 27, 250–281 (2011)
Skrzypek, J.J., Ganczarski, A.: Modeling of damage effect on heat transfer in time-dependent nonhomogeneous solids. J. Therm. Stress. 21, 205–231 (1998)
Skrzypek, J.J., Ganczarski, A.W., Rustichelli, F., Egner, H.: Advanced Materials and Structures for Extreme Operating Conditions. Springer, Berlin (2008)
Streilein, T.: Erfassung formativer Verfestigung in viskoplastischen Stoffmodellen, pp. 97–83. Institut für Statik der TU Braunschweig (1997)
Swift, H.W.: Plastic instability under plane stress. J. Mech. Phys. Solids 1, 1–18 (1952)
Taleb, L., Cailletaud, G.: An updated version of the multimechanism model for cyclic plasticity. Int. J. Plast. 26, 859–874 (2010)
Velay, V., Bernhart, G., Penazzi, L.: Cyclic behavior modeling of a tempered martensitic hot work tool steel. Int. J. Plast. 22, 459–496 (2006)
Xiao, H., Bruhns, T., Meyers, A.: Thermodynamic laws and consistent Eulerian formulation of finite elastoplasticity with thermal effects. J. Mech. Phys. Solids 55, 338–365 (2007)
Yoon, J.W., Barlat, F., Gracio, J.J., Rauch, E.: Anisotropic strain hardening behavior in simple shear for cube textured aluminum alloy sheets. Int. J. Plast. 21, 2426–2447 (2005)
Yoon, J.W., Barlat, F., Dick, R.E., Karabin, M.E.: Prediction of six or eight ears in a drawn cup based on a new anisotropic yield function. Int. J. Plast. 22, 174–193 (2006)
Yoon, J.W., Lou, Y., Yoon, J., Glazoff, M.V.: Asymmetric yield function based on the stress invariants for pressure sensitive metals. Int. J. Plast. 56, 184–202 (2014)
Yu, D., Chen, X., Yu, W., Chen, G.: Thermo-viscoplastic modeling incorporating dynamic strain aging effect on the uniaxial behavior of Z2CND18.12N stainless steel. Int. J. Plast. 37, 119–139 (2012)
Zhang, Z., Bernhart, G., Delagnes, D.: Cyclic behavior constitutive modeling of a tempered martensitic steel including ageing effect. Int. J. Fatigue 30, 706–716 (2008)
Zhang, Z., Delagnes, D., Bernhart, G.: Ageing effect on cyclic plasticity of a tempered martensitic steel. Int. J. Fatigue 29(2), 336–346 (2007)
Zhang, Z., Qi, Y., Delagnes, D., Bernhart, G.: Microstructure variation and hardness diminution during low cycle fatigue of 55NiCrMoV7 steel. J. Iron Steel Res. 14(6), 68–73 (2007)
Zhang, Z., Delagnes, D., Bernhart, G.: Anisothermal cyclic plasticity modeling of martensitic steels. Int. J. Fatigue 24, 635–648 (2002)
Ziegler, H.: Some extremum principles in irreversible thermodynamics with applications to continuum mechanics. In: Sneddon, I.N., Hill, R. (eds.) Progress is Solid Mechanics, pp. 92–193. North-Holland, Amsterdam (1963)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2015 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Egner, H., Egner, W. (2015). Classification of Constitutive Equations for Dissipative Materials—General Review. In: Skrzypek, J., Ganczarski, A. (eds) Mechanics of Anisotropic Materials. Engineering Materials. Springer, Cham. https://doi.org/10.1007/978-3-319-17160-9_7
Download citation
DOI: https://doi.org/10.1007/978-3-319-17160-9_7
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-17159-3
Online ISBN: 978-3-319-17160-9
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)