Abstract
A nanoindentation hardness testing system, including an atomic-force microscope (AFM)-based nanoindentation tester and a calibration method using electrolytically polished single-crystal metals as references, was proposed. This was applied to a study of the mechanical properties of fine-grained ferritic steel (grain size of 1.2 µm) and coarse-grained ferritic steel (30 µm). An empirical function giving the macroscopic hardness for all four reference metals from the nanoindentation force curves was established. The converted Vickers hardness (HV*) of the coarse-grained steel is almost independent of the indent size. The fine-grained steel shows only HV* 130 with an indent of only 100 nm, compared with a macroscopic hardness of HV 210. The difference, HV 80, is considered to reflect the amount of grain-boundary strengthening. The critical indent size for the hardness transition seems to be around 1 µm, comparable to the grain size of the specimen. This result supports the explanation of grainboundary strengthening. It is also consistent with Pickering’s work on low-carbon steel, as the estimated locking parameter (k of 2.6×105 N/m3/2) in the Hall-Petch relationship is in good agreement with his value of 2.4×105 N/m3/2.
Similar content being viewed by others
References
W.D. Nix: Mater. Sci. Eng., 1997, vols. A234–A36, pp. 37–44.
W.B. Morrison: Trans. ASM, 1966, vol. 59, pp. 825–46.
A. Sato: Bull. Iron Steel Inst. Jpn., 1998, vol. 3, pp. 88–89; see also Ultra-Steels Research Project home page at http://www.nrim.go.jp:8080/frontier/ext/frcsm/.
W.C. Oliver and G.M. Pharr: J. Mater. Res., 1992, vol. 7, pp. 1564–83.
K.W. McElhaney, J.J. Vlassak, and W.D. Nix: J. Mater. Res., 1998, vol. 13, pp. 1300–06
J.S. Field and M.V. Swain: J. Mater. Res., 1993, vol. 8, pp. 297–306
M. Atkinson: J. Mater. Sci., 1998, vol. 33, pp. 2937–47.
D. Tabor: The Hardness of Metals, Clarendon Press, Oxford, United Kingdom, 1951, pp. 112 and 166.
S. Nishijima, A. Ishii, K. Kanazawa, S. Matsuoka, and C. Masuda: Fundamental Fatigue Properties of JIS Steels for Machine Structural Use, National Research Institute for Metals, Ibaraki, 1989, p. 77.
G. Farges and D. Degout: Thin Solid Films, 1989, vol. 181, pp. 365–74.
S.J. Bull, T.F. Page, and E.H. Yoffe: Phil. Mag. Lett., 1989, vol. 59, pp. 281–88.
S.V. Hainsworth, H.W. Chandler, and T.F. Page: J. Mater. Res., 1996, vol. 11, pp. 1987–95
T. Hayashi, S. Torizuka, T. Mitsui, K. Tsuzaki, and K. Nagai: CAMP-ISIJ, 1999, vol. 12, pp. 385–88.
K. Miyahara, S. Matsuoka, N. Nagashima, and S. Mishima: Trans. Jpn. Soc. Mech. Eng. A, 1995, vol. 61, pp. 2321–28.
K. Miyahara, N. Nagashima, T. Ohmura, and S. Matsuoka: Nanostruc. Mater., 1999, vol. 12, pp. 1049–52.
T. Sawa and K. Tanaka: Nagaoka University of Technology, Nagaoka, unpublished work, 2000.
K. Miyahara, N. Nagashima, S. Matsuoka, and T. Ohmura: Trans. Jpn. Soc. Mech. Eng. A, 1998, vol. 64, pp. 2567–73
ASTM Designation E112-88, ASTM, Philadelphia, PA, 1988.
K. Miyahara, S. Matsuoka, and N. Nagashima: JSME Int. J., 1998, vol. 41A, pp. 562–68.
F.B. Pickering: Physical Metallurgy and the Design of Steels, Applied Science Publishers Ltd, London, 1978, p. 7.
F.B. Pickering: Physical Metallurgy and the Design of Steels, Applied Science Publishers Ltd, London, 1978, p. 63.
S. Miyazaki, K. Shibata, and H. Fujita: Acta Metall., 1978, vol. 27, pp. 855–62.
J.E. Bailey and P.B. Hirsch: Phil. Mag., 1960, vol. 5, pp. 485–97.
M.F. Ashby: Phil. Mag., 1970, vol. 21, pp. 399–424.
T. Narutani and T. Takamura: Acta Metall. Mater., 1991, vol. 39, pp. 2037–49.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Miyahara, K., Matsuoka, S. & Hayashi, T. Nanoindentation as a strength probe—a study on the hardness dependence of indent size for fine-grained and coarse-grained ferritic steel. Metall Mater Trans A 32, 761–768 (2001). https://doi.org/10.1007/s11661-001-0091-0
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-001-0091-0